LTC2345CUK-18 - Octal 18-bit 200kSps Diff SoftSpan ADC | ADI
Référence : LTC2345CUK-18 ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $38.5 | $38,50 |
| 10 | $35.2 | $352,00 |
| 100 | $30.75 | $3 075,00 |
| 500 | $27.4 | $13 700,00 |
| 1 000 | $24.95 | $24 950,00 |
LTC2345CUK-18 Présentation
A SoftSpan ADC is a successive approximation converter whose input voltage range can be reconfigured on a per-conversion, per-channel basis via internal programmable gain stages. Within the data-converter hierarchy, SAR ADCs sit between flash converters (fastest, lowest resolution) and sigma-delta ADCs (highest resolution, lower bandwidth). The LTC2345CUK-18 occupies the multi-channel, medium-resolution, low-latency niche where simultaneous acquisition of several signals is required without the latency penalty of sigma-delta.
Key differentiating features include eight truly differential input channels sampled through an 8-channel simultaneous-sampling front end, per-conversion SoftSpan range selection across multiple bipolar and unipolar spans, and an integrated 2.048 V reference with buffer that eliminates external reference components. The QFN-48 (UK suffix) 7x7 mm package with exposed pad provides a low thermal resistance path and compact PCB footprint.
Typical applications include multi-axis industrial process control, multi-channel instrumentation, optical networking power monitoring, and programmable logic controller (PLC) analog front ends. The simultaneous-sampling capability is decisive in phased-array and vibration analysis where channel-to-channel skew would corrupt the measurement. As of 2026-10-13 pricing is held in distributor stock at DigiKey, Mouser, and authorized partners.
When designing with the LTC2345CUK-18, ensure the exposed pad is soldered to a continuous ground plane for thermal dissipation and reference decoupling. Reject NMC pins by tying them to known logic levels per the datasheet, and route the LVDS or SPI traces as 50 ohm controlled-impedance differential lines if LVDS mode is selected.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the standalone manufacturer datasheet.
Alternatives de remplacement direct pour LTC2345CUK-18 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
LTC2345IUK-18#PBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LTC2345CUK-18#TRPBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LTC2345IUK-18#TRPBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LTC2345CUK-18 Valeurs maximales et caractéristiques électriques
| Résolution | 18 bit |
| Number of Channels | 8 (differential) |
| Fréquence d'échantillonnage | 200 kSps (per channel) |
| ADC Architecture | SAR (Successive Approximation Register) |
| Sampling Type | Simultaneous sampling |
| INL (Integral Non-Linearity) | ±5 LSB |
| No Missing Codes | 18 bits (guaranteed) |
| SNR (Signal-to-Noise Ratio) | 91.8 dB |
| Input Type | Differential, wide common-mode range |
| Input Span (SoftSpan) | Per-conversion, per-channel selectable |
| Tension d'alimentation | 4.75 V to 5.25 V (single 5 V) |
| Reference | Internal 2.048 V with buffer |
| Digital Interface | SPI CMOS (1.8 V to 5 V) or LVDS (pin-selectable) |
| Boîtier | 48-lead QFN (7x7 mm) UK suffix, exposed pad |
| Température de fonctionnement | 0C to +70C (C grade) |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant (PBF suffix) |
Configuration des broches de LTC2345CUK-18
| Broche 1 | IN0+ — Differential analog input channel 0 positive |
| Broche 2 | IN0- — Differential analog input channel 0 negative |
| Broche 3 | IN1+ — Differential analog input channel 1 positive |
| Broche 4 | IN1- — Differential analog input channel 1 negative |
| Broche 5 | IN2+ — Differential analog input channel 2 positive |
| Broche 6 | IN2- — Differential analog input channel 2 negative |
| Broche 7 | IN3+ — Differential analog input channel 3 positive |
| Broche 8 | IN3- — Differential analog input channel 3 negative |
| Broche 9 | GND — Analog ground |
| Broche 10 | REF — Reference voltage (internal 2.048 V) |
| Broche 11 | REFBUF — Reference buffer output |
| Broche 12 | GND — Analog ground |
| Broche 13 | VDD — 5 V analog supply |
| Broche 14 | GND — Analog ground |
| Broche 15 | VDD — 5 V analog supply |
| Broche 16 | GND — Analog ground |
| Broche 17 | IN4+ — Differential analog input channel 4 positive |
| Broche 18 | IN4- — Differential analog input channel 4 negative |
| Broche 19 | IN5+ — Differential analog input channel 5 positive |
| Broche 20 | IN5- — Differential analog input channel 5 negative |
| Broche 21 | IN6+ — Differential analog input channel 6 positive |
| Broche 22 | IN6- — Differential analog input channel 6 negative |
| Broche 23 | IN7+ — Differential analog input channel 7 positive |
| Broche 24 | IN7- — Differential analog input channel 7 negative |
| Broche 25 | GND — Analog ground |
| Broche 26 | OVDD — Digital interface supply (1.8 V to 5 V) |
| Broche 27 | GND — Digital ground |
| Broche 28 | SCK — Serial clock input (SPI/LVDS) |
| Broche 29 | SDI — Serial data input (SPI configuration) |
| Broche 30 | SDO — Serial data output |
| Broche 31 | CS — Chip select (active low, SPI mode) |
| Broche 32 | CNV — Conversion start input |
| Broche 33 | BUSY — Conversion busy output |
| Broche 34 | LVDS/CMOS — Interface mode select pin |
| Broche 35 | GND — Digital ground |
| Broche 36 | NC — Not connected (per datasheet) |
| Broche 37 | NC — Not connected (per datasheet) |
| Broche 38 | NC — Not connected (per datasheet) |
| Broche 39 | NC — Not connected (per datasheet) |
| Broche 40 | NC — Not connected (per datasheet) |
| Broche 41 | GND — Digital ground |
| Broche 42 | NC — Not connected (per datasheet) |
| Broche 43 | NC — Not connected (per datasheet) |
| Broche 44 | NC — Not connected (per datasheet) |
| Broche 45 | NC — Not connected (per datasheet) |
| Broche 46 | NC — Not connected (per datasheet) |
| Broche 47 | NC — Not connected (per datasheet) |
| Broche 48 | EP — Exposed pad - thermal/ground (must be soldered to PCB ground plane) |
Applications typiques
LTC2345CUK-18 convient pour 6 applications: Multi-Channel Industrial Process Control, Optical Networking Power Monitoring, Vibration and Phased-Array Analysis, Multi-Channel Instrumentation, PLC Analog Front End, Medical Multi-Signal Acquisition.
Multi-Channel Industrial Process Control
The LTC2345CUK-18 fits multi-axis industrial process control with eight differential inputs sampled simultaneously, each spanning 0 to 5 V unipolar or ±10 V bipolar via SoftSpan. Its ±5 LSB INL and 91.8 dB SNR deliver the headroom required to resolve 4-20 mA loop signals through a 250 ohm shunt with 16-bit effective precision after calibration. Reject common-mode cycle delay by sampling all eight loops on the same CNV chain simultaneously - critical when downstream loops must produce equal time-stamp. Power-grid and factory PLC deployments use this approach to compress acquisition BOM by replacing 8 single-channel ADCs with 1 octal part.
Recommandé
Optical Networking Power Monitoring
The LTC2345CUK-18 is well matched to optical networking power monitoring, where bias-tee photodiode currents span from microamps to milliamps across the eight transceiver channels. Its 91.8 dB SNR and 18-bit resolution cover this wide dynamic range without range-switching relays or per-channel PGAs, and simultaneous sampling removes channel-to-channel skew that corrupts per-wavelength power calibration. The integrated 2.048 V reference and buffer eliminate external REF decoupling, simplifying the densely-routed QSFP-DD or OSFP monitor front-end board. Reject common-mode cycle delay by tying the analog and digital grounds with a ferrite bead at the package exposed pad.
Recommandé
Vibration and Phased-Array Analysis
The LTC2345CUK-18 suits vibration and phased-array analysis through its eight-channel simultaneous sampling, which preserves channel-to-channel phase relationships that sequential ADCs destroy. Reject common-mode cycle delay by sampling all eight accelerometers or hydrophones on the same conversion cycle, with 200 kSps per channel comfortably above the 20 kHz Nyquist for industrial vibration and ultrasonic phased-array work. The pin-selectable LVDS interface maintains signal fidelity over the long board-to-FPGA distances typical of phased-array backplanes, and SoftSpan per-conversion range selection adapts a single device to both low-amplitude accelerometer and high-amplitude geophone channels in the same array.
Recommandé
Multi-Channel Instrumentation
The LTC2345CUK-18 fits multi-channel instrumentation, including bench-top DMMs, audio analyzers, and scientific data loggers where eight 18-bit channels must operate without channel-to-channel skew. Its 91.8 dB SNR meets the dynamic range required for audio-bandwidth measurements (>=20 kHz full-power bandwidth) and per-conversion SoftSpan allows each channel to be set independently to a 0-5 V, 0-10 V, or ±5 V / ±10 V range without external PGAs. The integrated reference and buffer eliminate thermal drift caused by external reference warm-up, improving the linearity needed for ratiometric measurements. Reject ground bounce by routing SPI/LVDS traces over a continuous ground plane.
Recommandé
PLC Analog Front End
The LTC2345CUK-18 suits PLC analog front ends where 8 differential channels replace the discrete ADC-plus-multiplexer architecture of legacy designs. Its 200 kSps per channel rate handles 8 channels at the 1 kHz to 10 kHz update rates typical of process-control scan cycles with substantial margin. The pin-selectable SPI CMOS (1.8 V to 5 V) interface connects directly to 3.3 V PLC CPUs without level shifters, while the LVDS option supports isolated front ends via digital isolators. Reject common-mode cycle delay by synchronizing all CNV chain operations to the PLC scan trigger.
Recommandé
Medical Multi-Signal Acquisition
The LTC2345CUK-18 fits medical multi-signal acquisition such as patient monitors, infusion-pump verification rigs, and electro-physiology front ends where 8 differential channels with 18-bit resolution capture ECG, EEG, EMG, or bio-potential signals with high CMRR. Its simultaneous sampling preserves the millisecond-level timing relationships that bio-signal algorithms depend on, and its 91.8 dB SNR covers the wide dynamic range between micro-volt EEG and milli-volt ECG inputs without range switching. The integrated reference and buffer simplify the IEC 60601-1 isolation barrier by reducing external components. Reject ground loops by isolating the analog front end with a high-CMRR isolation amplifier ahead of the ADC inputs.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LTC2345CUK-18 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LTC2345IUK-18#PBF | LTC2345CUK-18#TRPBF | LTC2345IUK-18#TRPBF |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 48-QFN (7x7) UK | 48-QFN (7x7) UK - same | 48-QFN (7x7) UK - same | 48-QFN (7x7) UK - same |
| Resolution | 18 bit | 18 bit | 18 bit | 18 bit |
| Sampling Rate | 200 kSps/ch | 200 kSps/ch | 200 kSps/ch | 200 kSps/ch |
| Channels | 8 differential | 8 differential | 8 differential | 8 differential |
| Operating Temperature | 0C to +70C | -40C to +85C | 0C to +70C | -40C to +85C |
| Digital Interface | SPI CMOS / LVDS | SPI CMOS / LVDS | SPI CMOS / LVDS | SPI CMOS / LVDS |
| Internal Reference | Yes (2.048 V) | Yes (2.048 V) | Yes (2.048 V) | Yes (2.048 V) |
| Packaging Format | Tray | Tray | Tape & Reel | Tape & Reel |
Principaux différenciateurs
- Octal simultaneous-sampling SAR in a single 48-QFN UK package (vs Discrete 8x single-channel SAR solutions)
- Per-conversion SoftSpan input range selection (vs Fixed-range SAR ADCs (e.g. AD7606))
- Pin-selectable SPI CMOS or LVDS interface (vs SPI-only competitive parts)
- Integrated 2.048 V reference and buffer (vs External-reference SAR ADCs)
Notes de conception
Solder the exposed pad (EP, pin 48) of the 48-lead QFN UK package to a continuous ground plane using an array of thermal vias underneath the EP. This provides the low-impedance ground return required by the internal reference and buffer, and conducts dissipated power (~250 mW at full 200 kSps across 8 channels) out of the die. Without proper EP soldering, reference noise and INL degrade noticeably. Place the 10uF X7R bypass caps on VDD and OVDD within 0.1 inch of the respective pins to reject switching noise.
Route the SPI or LVDS digital traces as 50 ohm controlled-impedance differential pairs (LVDS) or 50 ohm single-ended (CMOS) over a continuous ground plane. Keep digital traces away from the analog input pins (IN0+/- through IN7+/-) and the REF/REFBUF pins. If LVDS mode is selected, the 100 ohm differential termination must be placed within 0.5 inch of the LTC2345CUK-18 SDO+/SDO- pins to prevent reflections that would corrupt the 200 kSps data capture. Tie the LVDS/CMOS pin (pin 34) to OVDD or GND before the rising edge of VDD to latch the interface mode at power-up.
Do not exceed the absolute maximum 5.5 V on VDD or OVDD. Do not leave the LVDS/CMOS pin floating - it must be tied to a known logic level (OVDD for LVDS, GND for SPI CMOS) before VDD crosses VDD_min. Do not omit the REFBUF decoupling cap (10uF X7R + 0.1uF NP0 in parallel) - without it, REFBUF noise will degrade SNR below the 91.8 dB datasheet figure. When CNV is held low between conversions, ensure the BUSY output has returned high before reading SDO to avoid data races. Tie all NC pins to known logic levels per datasheet section 'Pin Functions'.
Informations de conformité
RoHS and REACH compliant per the PBF suffix designation (lead-free, RoHS-compliant). AEC-Q100 not qualified - the C grade (commercial 0C to +70C) and I grade (industrial -40C to +85C) are not automotive-qualified; consult Analog Devices for automotive-grade octal SAR options. Halogen-free status not stated in the verified distributor data - confirm with the manufacturer datasheet's materials declaration.
