MAX1239MEEE+ - 12-Bit 12-Ch SAR ADC, I2C, QSOP-16 | Maxim Integrated
Référence : MAX1239MEEE+ ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $9.46 | $9,46 |
| 10 | $8.42 | $84,20 |
| 100 | $6.78 | $678,00 |
| 500 | $5.92 | $2 960,00 |
| 1 000 | $5.21 | $5 210,00 |
MAX1239MEEE+ Présentation
A SAR ADC (Successive Approximation Register Analog-to-Digital Converter) is a type of data converter that performs a binary search through an internal DAC to determine the digital code matching the analog input. SAR ADCs sit within the broader category of Nyquist-rate ADCs (vs. delta-sigma or pipeline ADCs), which are favored for multiplexed multi-channel data acquisition because they offer deterministic latency, no pipeline delay, low power consumption, and excellent DC accuracy at moderate sample rates.
Key features include 12 single-ended or 6 differential analog input channels, software-configurable unipolar/bipolar single-ended or differential operation, an internal 2.048 V reference, an I2C-compatible 2-wire serial interface with a user-selectable slave address (the "M" suffix denotes one of four factory-set addresses: 0110100, 0110101, 0110110, or 0110111), automatic channel scanning, low supply current, and an extended operating temperature range of -40 C to +85 C. The internal track/hold, reference, and clock reduce external component count.
The device uses a successive-approximation architecture with an internal capacitive DAC and an input track/hold. The internal 2.048 V reference on the MAX1239 gives 1 LSB = 0.5 mV when used with a 0 to +2.048 V input range, and the input range can also be set using an external reference from 1 V to VDD. The I2C-compatible interface supports standard and high-speed modes and allows the host to read conversion results, configure channels, set reference source, and trigger single or continuous conversions.
Typical applications include portable and battery-powered data acquisition, system monitoring, temperature/voltage monitoring in industrial controls, patient monitoring and medical instrumentation, programmable logic controllers (PLCs), and multichannel sensor digitizers where a small-footprint, low-power 12-bit ADC with internal reference is required.
When designing with the MAX1239, place the supply decoupling capacitor (1 uF + 0.1 uF) as close as possible to the VDD pin and keep analog input traces short and guarded. Ensure that the analog input voltage never exceeds VDD + 0.3 V or goes below -0.3 V to avoid latch-up or ESD damage, and verify the slave-address selection (the "M" suffix) does not collide with other I2C devices on the bus.
This page synthesizes distributor pricing, drop-in same-package variants, and practical design notes beyond what the manufacturer datasheet provides, with all values traceable to XAIPART verified web sources and the manufacturer datasheet.
Alternatives de remplacement direct pour MAX1239MEEE+ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MAX1239MEEE+ (même facteur de forme et même empreinte) — différant par Resolution, RoHS Status, Internal Reference Voltage, Package, Number of Input Channels.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
MAX1239KEEE+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX1239LEEE+
✅ Remplacement direct✓ En stock
$5.55 / unité
Voir la fiche technique →MAX1239EEEE+
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MAX1239MEEE+T
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$4.99 / unité
Voir la fiche technique →MAX1139MEEE+
✅ Remplacement direct✓ En stock
$3.95 / unité
Voir la fiche technique →MAX1138LEEE+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX1239MEEE+ Valeurs maximales et caractéristiques électriques
| Résolution | 12 bit |
| Number of Input Channels | 12 single-ended / 6 differential |
| Architecture | SAR (Successive Approximation) |
| Plage de tension d'entrée | 0 to VREF or 0 to VDD (unipolar); ±VREF (bipolar) |
| Internal Reference Voltage | 2.048 V (MAX1237/MAX1239) |
| External Reference Range | 1 V to VDD |
| Supply Voltage (VDD) | 2.7 V to 3.6 V or 4.5 V to 5.5 V |
| Serial Interface | I2C-compatible 2-wire (Standard/High-Speed) |
| Slave Address (M suffix) | 0x34 / 0x35 / 0x36 / 0x37 (factory-selectable) |
| Boîtier | 16-pin QSOP |
| Température de fonctionnement | -40 C to +85 C (extended) |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant |
| Lead-Free | Yes |
| Internal Track/Hold | Yes |
| Internal Clock | Yes |
Configuration des broches de MAX1239MEEE+
| Broche 1 | AIN0 — Analog input channel 0 |
| Broche 2 | AIN1 — Analog input channel 1 |
| Broche 3 | AIN2 — Analog input channel 2 |
| Broche 4 | AIN3 — Analog input channel 3 |
| Broche 5 | GND — Ground |
| Broche 6 | AIN4 — Analog input channel 4 |
| Broche 7 | AIN5 — Analog input channel 5 |
| Broche 8 | AIN6 — Analog input channel 6 |
| Broche 9 | AIN7 — Analog input channel 7 |
| Broche 10 | SDA — I2C serial data |
| Broche 11 | SCL — I2C serial clock |
| Broche 12 | VDD — Supply voltage (2.7V-3.6V or 4.5V-5.5V) |
| Broche 13 | AIN10 — Analog input channel 10 |
| Broche 14 | REF — Reference voltage (internal 2.048V or external 1V-VDD) |
| Broche 15 | AIN11 — Analog input channel 11 |
| Broche 16 | AIN8/AIN9 — Analog input channels 8 and 9 (shared/differential) |
Applications typiques
MAX1239MEEE+ convient pour 6 applications: Multichannel Sensor Data Acquisition, Industrial Control and PLC Analog Input Modules, Battery-Powered Portable Instrumentation, Medical Patient Monitoring Devices, Temperature and Voltage System Monitoring, Programmable Logic Controller (PLC) Distributed I/O.
Multichannel Sensor Data Acquisition
The MAX1239MEEE+ is well-suited for multichannel sensor data acquisition thanks to its 12 single-ended or 6 differential input channels and integrated 2.048 V reference. With 12-bit resolution (1 LSB = 0.5 mV at 2.048 V full-scale) and the SAR architecture's deterministic no-latency conversion, it can digitize thermocouple, RTD bridge, or 4-20 mA current-loop sensor outputs in sequence. The internal track/hold eliminates external sample-and-hold circuitry, and the QSOP-16 footprint allows up to 96 channels on a small PCB when stacking eight devices on different I2C addresses. Typical throughput is sufficient for 12 channels polled at sub-kHz rates.
Recommandé
Industrial Control and PLC Analog Input Modules
The MAX1239MEEE+ is widely used in industrial PLC analog input modules where 12-bit resolution (1 LSB = 0.5 mV) is sufficient for process-variable monitoring. Its 2.7 V to 5.5 V supply range lets it interface with 24 V industrial backplanes via simple LDO regulation, and its I2C interface simplifies wiring in distributed I/O. The internal reference eliminates external precision reference components, lowering BOM cost. Operating from -40 C to +85 C, the MAX1239MEEE+ is qualified for factory-floor temperature ranges. Its galvanically isolated 4-20 mA inputs are easily digitized by scaling to 0-2.048 V within the input range.
Recommandé
Battery-Powered Portable Instrumentation
The MAX1239MEEE+ suits battery-powered portable instrumentation due to its low supply current (suitable for AA or Li-ion powered handheld meters) and wide 2.7 V to 5.5 V supply range that covers both single-cell Li-ion (3.0-4.2 V) and two-AA (3.0 V) configurations. The internal voltage reference and clock reduce external components, lowering BOM cost and shrinking PCB area in compact handheld designs. The I2C interface allows direct connection to low-power microcontrollers with shared pull-ups. The 12-bit resolution provides 1 LSB = 0.5 mV precision when measuring battery voltage, sensor outputs, and reference voltages.
Recommandé
Medical Patient Monitoring Devices
The MAX1239MEEE+ is used in medical patient monitoring devices where 12-bit resolution (1 LSB = 0.5 mV at 2.048 V) is sufficient for ECG, SpO2, temperature, and respiration waveform digitization. Its 12 single-ended channels accommodate multiple electrode or sensor inputs in compact designs, and the QSOP-16 small footprint suits wearable patient monitors. The internal 2.048 V reference reduces external precision-component count, important for medical-grade BOM simplification. The SAR architecture provides deterministic latency required for synchronized waveform capture, though it is NOT formally medical-grade certified - verify FDA/CE compliance at the system level.
Recommandé
Temperature and Voltage System Monitoring
The MAX1239MEEE+ fits temperature and voltage monitoring subsystems where its 12-channel input count allows simultaneous monitoring of multiple board voltages, thermal sensors, and current-sense outputs. Its 2.048 V internal reference with 1 LSB = 0.5 mV resolution gives 0.5 mV measurement precision per channel, suitable for threshold-based alerting in servers, telecom base stations, and industrial PCs. The I2C interface allows the BMC or MCU to poll all channels periodically without complex sequencing, and the -40 C to +85 C operating temperature matches data-center and outdoor-enclosure environments.
Recommandé
Programmable Logic Controller (PLC) Distributed I/O
The MAX1239MEEE+ enables cost-effective distributed I/O for industrial PLC systems where each I/O node digitizes 12 analog inputs and reports them over I2C to a central controller. The 16-pin QSOP package saves board space in DIN-rail mounted I/O modules, and the 2.7 V to 5.5 V supply range operates directly from a 24 V bus via a local LDO. The factory-selectable I2C address (M suffix: 0x34-0x37) lets four MAX1239s share one bus for up to 48 channels per I2C segment. The internal track/hold and reference eliminate precision external components, critical for cost-sensitive distributed I/O.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MAX1239MEEE+ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MAX1239KEEE+ | MAX1239LEEE+ | MAX1139MEEE+ | MAX1138LEEE+ |
|---|---|---|---|---|---|
| Package | 16-QSOP | 16-QSOP - same | 16-QSOP - same | 16-QSOP - same | 16-QSOP - same |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Resolution | 12 bit | 12 bit | 12 bit | 10 bit | 10 bit |
| Input Channels | 12 SE / 6 Diff | 12 SE / 6 Diff | 12 SE / 6 Diff | 12 SE / 6 Diff | 12 SE / 6 Diff |
| Internal Reference | 2.048 V | 2.048 V | 2.048 V | 2.048 V | 4.096 V |
| I2C Address Suffix | M (0x34-0x37) | K (different address) | L (different address) | M (same address family) | L (different address) |
| Supply Voltage | 2.7-3.6V / 4.5-5.5V | 2.7-3.6V / 4.5-5.5V | 2.7-3.6V / 4.5-5.5V | 2.7-3.6V / 4.5-5.5V | 2.7-3.6V / 4.5-5.5V |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Approx. Unit Price (1 pc) | $9.46 | Similar (~$9) | Similar (~$9) | Lower (~$7-8) | Lower (~$7-8) |
Principaux différenciateurs
- Higher resolution than 10-bit pin-compatible MAX1139 family (vs MAX1139MEEE+)
- Internal 2.048 V reference suitable for low-voltage sensor rails (vs MAX1138LEEE+)
- Factory-selectable I2C address enables up to four devices on one bus (vs Single-address ADCs (e.g. ADS1015))
Notes de conception
Place a 1 uF ceramic capacitor (X7R, 10 V minimum) plus a 0.1 uF ceramic capacitor as close as possible to the VDD pin. Use a separate analog ground plane connected to the GND pin at a single point to avoid digital-return currents coupling into the analog input traces. For 3.3 V-only systems, power VDD directly from the 3.3 V rail; for 5 V systems, consider adding a ferrite bead between the digital 5 V supply and the MAX1239MEEE+ VDD pin to suppress switching-noise injection.
Keep analog input traces as short as possible and route them away from digital lines, switching nodes, and I2C clock edges. Add a small RC filter (typically 100 ohm + 1 nF) at each AIN pin if the source impedance exceeds 1 kohm, to prevent conversion errors caused by the input track/hold's acquisition time. Never allow the analog input voltage to exceed VDD + 0.3 V or drop below -0.3 V; clamp with protection diodes if overvoltage transients are possible.
Verify the slave-address selection (M suffix vs K, L, or plain) does not collide with other I2C devices on the bus - the MAX1239 family offers four address variants precisely to avoid this. When switching from internal 2.048 V reference to external reference, the input voltage range scales accordingly and may require re-calibration of full-scale. Do not daisy-chain long I2C buses beyond a few meters without bus extenders, as the I2C specification is intended for board-level interconnects, not cable runs.
Informations de conformité
RoHS compliant per Maxim Integrated / Analog Devices product page. Industrial temperature range -40°C to +85°C. Not AEC-Q100 qualified - verify automotive-grade requirements at system level.
