Analog Devices

MAX232MJE/883B - 5V Dual RS-232 Transceiver | Analog Devices

Référence : MAX232MJE/883B ✓ Actif
+5 V Vdss V.28 and V.24 Rds(on) 16-pin CDIP Package
MOQ : 1 |

MAX232MJE/883B Présentation

Analog Devices MAX232MJE/883B is a +5 V-powered, dual RS-232 transceiver containing two line drivers and two receivers in a 16-pin CDIP package. It implements EIA/TIA-232E and V.28/V.24 communications interfaces when a traditional ±12 V supply is unavailable. The device converts logic-level TXD and RIN signals to RS-232 levels and converts incoming RS-232 signals back to CMOS-compatible logic levels.

An RS-232 transceiver is a bidirectional interface IC used within the serial communications hierarchy. Its transmitters translate digital logic into single-ended, bipolar RS-232 signals, while its receivers recover logic signals from those physical-layer waveforms. This interface level lies between UART-compatible digital equipment and a DB9 or equivalent connector. The MAX220–MAX249 family was designed specifically for EIA/TIA-232E and V.28/V.24 links where ±12 V is not practical.

The MAX232MJE/883B provides two transmit channels and two receive channels from a single 5 V rail. Its +5 V operation simplifies power architecture in embedded systems, while the dual-channel arrangement supports two serial ports or one bidirectional port with spare channels. The /883B designation identifies a screened product variant, making the device relevant to systems that require controlled procurement and qualification rather than only commercial-temperature production.

Internally, the MAX232 family uses charge-pump circuitry to develop the positive and negative voltages required by RS-232 drivers. Typical implementation requires external charge-pump capacitors and local supply decoupling close to the device. The transmitter and receiver architecture separates logic-side inputs and outputs from the external cable-facing pins, allowing logic-level equipment to connect through a protected or standardized RS-232 interface.

Typical applications include industrial serial consoles, point-of-sale terminals, instrumentation interfaces, embedded data acquisition, and legacy peripheral connections. Two transmitters and two receivers are useful when a controller must communicate with two RS-232 endpoints, or when a design requires two independent transmit-only links alongside receive channels. Cable length, ground reference, protection, and signal polarity must be checked against the interface standard used by the connected equipment.

The main layout consideration is to place the required charge-pump and bypass capacitors close to their associated pins. Keep the logic-side traces away from cable-side driver outputs, use a solid ground plane, and place transient-protection components at the connector rather than beside the IC. Account for the voltage and temperature limits of the selected capacitor dielectric before committing to the final component set.

This page combines interface specifications, package details, drop-in replacement analysis, and practical PCB guidance. It also distinguishes the screened MAX232MJE/883B from commercial and older grade variants so engineers can make a qualification-aware selection without changing the 16-pin CDIP footprint.

Alternatives de remplacement direct pour MAX232MJE/883B — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

MAX232MJE

✅ Remplacement direct ⚠️ Spécifications non vérifiées
📦 16-pin CDIP
Same dual-driver, dual-receiver RS-232 architecture and 16-pin CDIP footprint; the /883B suffix adds a distinct screening designation, with 0% difference in the stated basic channel and supply configuration.

📋 Alternative de référence (hors catalogue)

MAX232EJE

✅ Remplacement direct ⚠️ Spécifications non vérifiées
📦 16-pin CDIP
Same +5 V, 2/2 RS-232 function and 16-pin CDIP footprint; the primary documented difference is the commercial E-grade designation rather than the /883B screening designation.

📋 Alternative de référence (hors catalogue)

MAX232MJE/883

✅ Remplacement direct ⚠️ Spécifications non vérifiées
📦 16-pin CDIP
Same +5 V, 2/2 RS-232 architecture and 16-pin CDIP footprint as MAX232MJE/883B; difference is the revision suffix of the screened ordering code, with no stated change to the basic interface configuration.

📋 Alternative de référence (hors catalogue)

MAX232MJE/883B Spécifications

Product Type RS-232 transceiver
Tension d'alimentation +5 V
Number of Transmitters 2
Number of Receivers 2
Interface Standard EIA/TIA-232E
Supporting Standards V.28 and V.24
Boîtier 16-pin CDIP
Type de montage Through-hole

Guide de configuration des broches du MAX232MJE/883B 16-pin cdip

Configuration des broches du MAX232MJE/883B (boîtier 16-pin cdip). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.

Schéma de brochage du boîtier 16-pin cdip pour le MAX232MJE/883B

Aucune donnée de brochage détaillée disponible pour MAX232MJE/883B.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

MAX232MJE/883B convient pour 6 applications: Industrial Serial Console, Point-of-Sale Terminal Interface, Instrumentation and Data Acquisition, Embedded Service and Configuration Port, Legacy Peripheral Connectivity, Automated Test Equipment Interface.

🏭

Industrial Serial Console

The MAX232MJE/883B fits an industrial console interface that must convert CMOS-compatible controller signals into RS-232 levels from a single +5 V rail. Two transmitters and two receivers allow the controller to monitor and control more than one serial endpoint while avoiding separate external line drivers. Its 16-pin CDIP package also suits through-hole industrial assemblies with generous spacing for routing and service access. The designer should still add connector-side transient protection, verify grounding between connected equipment, and use the MAX232 family datasheet when selecting charge-pump and bypass capacitors.

🖥️

Point-of-Sale Terminal Interface

The MAX232MJE/883B is appropriate for point-of-sale equipment that connects a low-voltage embedded controller to legacy RS-232 peripherals such as scales, printers, or customer displays. The +5 V supply requirement matches many embedded control platforms, while the two transmitters and two receivers support multiple device connections without adding another transceiver package. The through-hole CDIP format can simplify qualification in industrial point-of-sale products. Firmware should configure the UART correctly, and the PCB must maintain a common signal ground and place any cable transients at the connector boundary.

📡

Instrumentation and Data Acquisition

The MAX232MJE/883B can provide a compact RS-232 command link between instrumentation and a controller when ±12 V is unavailable. Its two transmitters and two receivers permit separate command and response channels, or support for two instrument ports, while the single +5 V rail simplifies system power design. The screened /883B ordering code is relevant when the purchasing specification requires controlled procurement. Engineers should treat the RS-232 interface as a point-to-point connection, minimize cable exposure, and add external surge protection where the installation environment permits electrical transients.

🔧

Embedded Service and Configuration Port

A MAX232MJE/883B-based service port gives an embedded controller a practical RS-232 connection for configuration, diagnostics, and firmware update commands. Two transmitter channels can support two service destinations, and two receiver channels can accept status or acknowledgment data, subject to the UART and protocol design. The +5 V-powered interface reduces the number of external rails required around the controller, while the 16-pin CDIP package supports conventional through-hole construction. Production designs should document connector pinout, cable length limits, logic polarity, and protective-device placement.

🔌

Legacy Peripheral Connectivity

The MAX232MJE/883B bridges modern CMOS logic and legacy RS-232 peripherals that do not support modern differential bus interfaces. Two transmitters and two receivers make it possible to connect more than one peripheral while keeping the interface level consistent with EIA/TIA-232E equipment expectations. Its single +5 V operation is especially useful where the legacy peripheral provides RS-232 signaling but not a modern supply rail. Validate the connected equipment's driver and receiver voltage levels, use a shared reference ground, and avoid substituting RS-485 or RS-422 parts without checking every signal and pin function.

⚡

Automated Test Equipment Interface

The MAX232MJE/883B can serve as the RS-232 interface between automated test equipment and a device under test when the test controller operates from 5 V logic. Two channels allow bidirectional command and result traffic, with additional channels available for fixtures or auxiliary instruments. The through-hole CDIP package is practical for laboratory and production-test fixtures assembled with conventional through-hole techniques. For reliable automated operation, define timeout behavior, isolate ground currents, protect the connector, and verify the maximum data rate and logic levels in the manufacturer's electrical tables.

Récapitulatif des produits recommandés

MAX232MJE Same-family RS-232 transceiver with the same dual-channel architecture Utilisé dans : Industrial Serial Console, Point-of-Sale Terminal Interface, Instrumentation and Data Acquisition, Embedded Service and Configuration Port, Legacy Peripheral Connectivity, Automated Test Equipment Interface ICL232MJE Related RS-232 transceiver family option Utilisé dans : Industrial Serial Console, Embedded Service and Configuration Port MAX232EJE Commercial-grade same-footprint family alternative Utilisé dans : Point-of-Sale Terminal Interface, Automated Test Equipment Interface MC1489NG4 Texas Instruments Utilisé dans : Instrumentation and Data Acquisition, Legacy Peripheral Connectivity
What is the MAX232MJE/883B?
The MAX232MJE/883B is a +5 V-powered, dual RS-232 transceiver with two drivers and two receivers in a 16-pin CDIP package. According to the Maxim Integrated MAX232 datasheet, it is intended for EIA/TIA-232E and V.28/V.24 communications interfaces where ±12 V is unavailable. It accepts CMOS-compatible logic signals and provides bipolar RS-232 line-level signaling for serial equipment.
Where can I download the MAX232MJE/883B datasheet PDF?
The MAX232MJE/883B datasheet is available through the official Analog Devices MAX232 product page at https://www.analog.com/en/products/MAX232.html. The family documentation describes the +5 V multichannel RS-232 drivers and receivers, EIA/TIA-232E and V.28/V.24 support, external charge-pump requirements, pin functions, and operating limitations. Use the manufacturer documentation for the authoritative schematic and electrical limits.
Where can I find the MAX232MJE/883B pinout?
The MAX232MJE/883B pinout is published in the MAX232 family datasheet on the official Analog Devices product page. The device uses a 16-pin CDIP outline, so engineers should map the family pin-description table onto the physical pin numbers before assigning PCB tracks. In particular, verify the driver outputs, receiver inputs, supply pins, ground pins, and external charge-pump capacitor connections against the diagram.
What are the key specifications of MAX232MJE/883B that engineers should know?
The principal MAX232MJE/883B specifications are a +5 V supply, two RS-232 transmitters, two receivers, and a 16-pin CDIP package. The Maxim Integrated family documentation identifies support for EIA/TIA-232E plus V.28 and V.24 interfaces. It was designed for systems lacking ±12 V supplies, with external charge-pump components required to support the bipolar RS-232 output levels.
How many RS-232 channels does MAX232MJE/883B provide?
The MAX232MJE/883B provides two transmitter channels and two receiver channels, for a total of four configurable RS-232 signal functions. The DigiKey product listing identifies the part as a 2/2 RS-232 transceiver, while the Maxim Integrated datasheet describes the MAX220–MAX249 family as multichannel line-driver and receiver products. This arrangement supports two complete ports or other combinations of transmit and receive links.
Does MAX232MJE/883B work from a single 5 V supply?
Yes, the MAX232MJE/883B operates from a single +5 V supply and internally generates the voltage levels required for RS-232 signaling. The Maxim Integrated datasheet specifically describes the MAX232 family as a +5 V-powered solution for applications where ±12 V is not available. External charge-pump capacitors are still required, and the supply bypass capacitor should be placed close to the device.
What interfaces are supported by MAX232MJE/883B?
The MAX232MJE/883B supports EIA/TIA-232E communications interfaces and is associated with V.28 and V.24 signaling requirements. These standards define the electrical behavior of RS-232 links, including driver levels, receiver thresholds, and connector-side signal relationships. The official Maxim Integrated datasheet is the appropriate reference when confirming system-level timing, grounding, and cable requirements.
Is MAX232MJE/883B suitable for industrial serial communication?
The MAX232MJE/883B is suitable for industrial serial interfaces when its specified operating-temperature and screening limits meet the equipment requirements. Its two transmitters, two receivers, and single +5 V supply simplify multiport serial designs. Industrial systems should also verify transient protection, ground continuity, cable length, and the qualification requirements of the complete assembly.
Can MAX232MJE replace MAX232MJE/883B?
The MAX232MJE can be a footprint-compatible alternative to MAX232MJE/883B because it represents the base MAX232 device in the same 16-pin CDIP family. The engineering difference is product screening and qualification rather than basic transceiver function. Before substitution, compare the manufacturer temperature grade, screening suffix, operating limits, and the procurement requirements of the finished system.
What can replace MAX232MJE/883B on an existing PCB?
The closest documented replacement is the base MAX232MJE in the same 16-pin CDIP family, with the MAX232EJE commercial-grade family variant offering another same-footprint option. Both retain the dual-driver and dual-receiver RS-232 function, but their qualification details should be checked before release. Use the manufacturer pin and electrical tables to confirm every net, including charge-pump capacitors.
When should I choose MAX232MJE/883B instead of MAX232MJE?
Choose MAX232MJE/883B when procurement or qualification requires the screened /883B product designation. Choose the base MAX232MJE when that grade is sufficient for the application and can reduce procurement complexity. Both use the same 16-pin CDIP architecture and provide two transmitters and two receivers, so the final decision should emphasize temperature grade, screening, documentation, and lifecycle requirements.
MAX232MJE/883B vs MAX232EJE: which is better for a production design?
The MAX232MJE/883B is the better choice when screened procurement and an extended-temperature-grade family position are required; MAX232EJE is the better choice for a commercial-temperature design that does not require the /883B designation. The MAX232EJE is functionally close and uses the same 16-pin CDIP footprint, but the exact temperature ratings and screening conditions must be confirmed from the manufacturer datasheets before substitution.
Where can I buy MAX232MJE/883B and what is its lead time?
Use the Request a Quote form on this page to check current availability, commercial terms, and lead time for MAX232MJE/883B. The device is identified in current catalog listings as a 16-CDIP, 2/2 RS-232 transceiver. Quote requests are the appropriate route for exact-suffix supply because production allocation can vary with screening grade, date code, and assembly volume.
Is MAX232MJE/883B in stock?
Current stock status for MAX232MJE/883B should be confirmed through the Request a Quote form on this page. Catalog entries show that the exact 16-CDIP /883B ordering code is actively offered, but a catalog listing does not guarantee a fixed quantity for every date code and production schedule. Request the required quantity and certification documentation with the quotation.
What is the price of MAX232MJE/883B?
Use the Request a Quote form on this page for the current MAX232MJE/883B commercial price. The quote can reflect exact MPN, quantity, date-code requirements, packaging needs, and shipment terms. Because this is a specific screened ordering code, request a written quotation rather than relying on a generic MAX232 price that may refer to a different grade or package.
How should charge-pump capacitors be placed around MAX232MJE/883B?
Place the MAX232MJE/883B charge-pump capacitors directly between their designated IC pins with the shortest possible traces, and place the supply bypass capacitor at the power and ground pins. The Maxim Integrated datasheet identifies the external capacitor connections required by the MAX232 family. Keep these switching-capacitor paths compact while routing cable-side driver outputs away from sensitive logic and analog traces.

Données de référence d'ingénierie pour MAX232MJE/883B — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose MAX232MJE/883B when the assembly requires the specific screened /883B ordering designation and a 16-pin CDIP interface IC operating from +5 V. Select MAX232MJE when the base grade satisfies procurement and qualification requirements while preserving the same dual-driver, dual-receiver architecture and footprint. MAX232EJE is appropriate for a commercial-grade design, but its exact temperature limits should be compared with the operating environment before substitution. MAX232MJE/883 is a closely related family ordering code whose qualification and revision requirements must be reviewed against the finished equipment specification. In every case, verify the pinout, charge-pump capacitor values, bypass capacitor, operating-temperature range, data rate, and RS-232 logic levels before approving a drop-in substitution.

Comparaison avec les alternatives

Paramètre Ce produit MAX232MJE MAX232EJE MAX232MJE/883
Package 16-pin CDIP 16-pin CDIP 16-pin CDIP 16-pin CDIP
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Product Type RS-232 transceiver RS-232 transceiver RS-232 transceiver RS-232 transceiver
Supply Voltage +5 V +5 V +5 V +5 V
Transmitters 2 2 2 2
Receivers 2 2 2 2
Interface Standard EIA/TIA-232E EIA/TIA-232E EIA/TIA-232E EIA/TIA-232E
Grade or Screening Designation /883B Base grade E grade /883

Principaux différenciateurs

  • Screened /883B ordering designation for procurement-aware assemblies (vs MAX232MJE)
  • Retains the same CDIP footprint as the base MAX232 (vs MAX232EJE)
  • Single-rail interface simplifies embedded serial links (vs MAX232MJE/883)

Notes de conception

Place all charge-pump capacitors as close as practical to the MAX232MJE/883B pins identified in the manufacturer pin-description table. Keep each capacitor connection short, symmetrical where the recommended circuit permits, and free of test-point stubs. The switching-capacitor loops should remain compact to limit radiated and conducted noise. Place the local supply bypass capacitor directly between the supply and ground pins rather than routing it around the board.

Separate logic-side nets from cable-side RS-232 nets when laying out the PCB. Route driver outputs directly toward the protection and connector area, and keep receiver inputs away from noisy power circuitry and switching nodes. Maintain a continuous ground reference beneath the device and return cable surge current through a deliberate protection path. This prevents transient current from flowing through sensitive logic traces and reduces susceptibility to communication errors.

Do not treat an RS-232 transceiver as a differential bus and do not interchange it with an RS-485 or RS-422 device. RS-232 is single-ended, and correct operation depends on signal polarity, reference ground, cable configuration, and the connected equipment's voltage levels. Before releasing a replacement, verify every receiver and transmitter connection, the required charge-pump capacitors, supply bypassing, temperature grade, and the qualification status of the exact ordering code.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The MAX232 family documentation identifies EIA/TIA-232E, V.28, and V.24 interface requirements. Product-specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the available catalog excerpts.

Recherches associées

MAX232MJE/883B datasheet MAX232MJE/883B pinout MAX232MJE/883B datasheet pdf MAX232MJE/883B equivalent MAX232MJE/883B replacement MAX232MJE/883B 16-CDIP MAX232MJE/883B RS-232 transceiver MAX232MJE/883B price MAX232MJE/883B stock Analog Devices MAX232MJE/883B MAX232MJE vs MAX232MJE/883B MAX232MJE/883B application circuit

Composants & termes associés

Analog Devices Maxim Integrated MAX232MJE/883B MAX232MJE MAX232EJE MAX232MJE/883 MAX220-MAX249 RS-232 transceiver line driver line receiver interface IC semiconductor EIA/TIA-232E V.28 V.24 +5 V power charge-pump capacitor CMOS-compatible logic 16-pin CDIP DIP through-hole package industrial serial communication point-of-sale terminal data acquisition transient protection
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ