MAX232MJE/883B - 5V Dual RS-232 Transceiver | Analog Devices
料号: MAX232MJE/883B ✓ 量产中MAX232MJE/883B 概述
An RS-232 transceiver is a bidirectional interface IC used within the serial communications hierarchy. Its transmitters translate digital logic into single-ended, bipolar RS-232 signals, while its receivers recover logic signals from those physical-layer waveforms. This interface level lies between UART-compatible digital equipment and a DB9 or equivalent connector. The MAX220–MAX249 family was designed specifically for EIA/TIA-232E and V.28/V.24 links where ±12 V is not practical.
The MAX232MJE/883B provides two transmit channels and two receive channels from a single 5 V rail. Its +5 V operation simplifies power architecture in embedded systems, while the dual-channel arrangement supports two serial ports or one bidirectional port with spare channels. The /883B designation identifies a screened product variant, making the device relevant to systems that require controlled procurement and qualification rather than only commercial-temperature production.
Internally, the MAX232 family uses charge-pump circuitry to develop the positive and negative voltages required by RS-232 drivers. Typical implementation requires external charge-pump capacitors and local supply decoupling close to the device. The transmitter and receiver architecture separates logic-side inputs and outputs from the external cable-facing pins, allowing logic-level equipment to connect through a protected or standardized RS-232 interface.
Typical applications include industrial serial consoles, point-of-sale terminals, instrumentation interfaces, embedded data acquisition, and legacy peripheral connections. Two transmitters and two receivers are useful when a controller must communicate with two RS-232 endpoints, or when a design requires two independent transmit-only links alongside receive channels. Cable length, ground reference, protection, and signal polarity must be checked against the interface standard used by the connected equipment.
The main layout consideration is to place the required charge-pump and bypass capacitors close to their associated pins. Keep the logic-side traces away from cable-side driver outputs, use a solid ground plane, and place transient-protection components at the connector rather than beside the IC. Account for the voltage and temperature limits of the selected capacitor dielectric before committing to the final component set.
This page combines interface specifications, package details, drop-in replacement analysis, and practical PCB guidance. It also distinguishes the screened MAX232MJE/883B from commercial and older grade variants so engineers can make a qualification-aware selection without changing the 16-pin CDIP footprint.
直接替换替代料: MAX232MJE/883B ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
MAX232MJE
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX232EJE
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX232MJE/883
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX232MJE/883B 规格参数
| Product Type | RS-232 transceiver |
| 电源电压 | +5 V |
| Number of Transmitters | 2 |
| Number of Receivers | 2 |
| Interface Standard | EIA/TIA-232E |
| Supporting Standards | V.28 and V.24 |
| 封装 | 16-pin CDIP |
| 安装类型 | Through-hole |
MAX232MJE/883B 16-pin cdip 引脚配置指南
MAX232MJE/883B(16-pin cdip 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX232MJE/883B.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX232MJE/883B 适用于 6 应用s: Industrial Serial Console, Point-of-Sale Terminal Interface, Instrumentation and Data Acquisition, Embedded Service and Configuration Port, Legacy Peripheral Connectivity, Automated Test Equipment Interface.
Industrial Serial Console
The MAX232MJE/883B fits an industrial console interface that must convert CMOS-compatible controller signals into RS-232 levels from a single +5 V rail. Two transmitters and two receivers allow the controller to monitor and control more than one serial endpoint while avoiding separate external line drivers. Its 16-pin CDIP package also suits through-hole industrial assemblies with generous spacing for routing and service access. The designer should still add connector-side transient protection, verify grounding between connected equipment, and use the MAX232 family datasheet when selecting charge-pump and bypass capacitors.
推荐
Point-of-Sale Terminal Interface
The MAX232MJE/883B is appropriate for point-of-sale equipment that connects a low-voltage embedded controller to legacy RS-232 peripherals such as scales, printers, or customer displays. The +5 V supply requirement matches many embedded control platforms, while the two transmitters and two receivers support multiple device connections without adding another transceiver package. The through-hole CDIP format can simplify qualification in industrial point-of-sale products. Firmware should configure the UART correctly, and the PCB must maintain a common signal ground and place any cable transients at the connector boundary.
推荐
Instrumentation and Data Acquisition
The MAX232MJE/883B can provide a compact RS-232 command link between instrumentation and a controller when ±12 V is unavailable. Its two transmitters and two receivers permit separate command and response channels, or support for two instrument ports, while the single +5 V rail simplifies system power design. The screened /883B ordering code is relevant when the purchasing specification requires controlled procurement. Engineers should treat the RS-232 interface as a point-to-point connection, minimize cable exposure, and add external surge protection where the installation environment permits electrical transients.
推荐
Embedded Service and Configuration Port
A MAX232MJE/883B-based service port gives an embedded controller a practical RS-232 connection for configuration, diagnostics, and firmware update commands. Two transmitter channels can support two service destinations, and two receiver channels can accept status or acknowledgment data, subject to the UART and protocol design. The +5 V-powered interface reduces the number of external rails required around the controller, while the 16-pin CDIP package supports conventional through-hole construction. Production designs should document connector pinout, cable length limits, logic polarity, and protective-device placement.
推荐
Legacy Peripheral Connectivity
The MAX232MJE/883B bridges modern CMOS logic and legacy RS-232 peripherals that do not support modern differential bus interfaces. Two transmitters and two receivers make it possible to connect more than one peripheral while keeping the interface level consistent with EIA/TIA-232E equipment expectations. Its single +5 V operation is especially useful where the legacy peripheral provides RS-232 signaling but not a modern supply rail. Validate the connected equipment's driver and receiver voltage levels, use a shared reference ground, and avoid substituting RS-485 or RS-422 parts without checking every signal and pin function.
推荐
Automated Test Equipment Interface
The MAX232MJE/883B can serve as the RS-232 interface between automated test equipment and a device under test when the test controller operates from 5 V logic. Two channels allow bidirectional command and result traffic, with additional channels available for fixtures or auxiliary instruments. The through-hole CDIP package is practical for laboratory and production-test fixtures assembled with conventional through-hole techniques. For reliable automated operation, define timeout behavior, isolate ground currents, protect the connector, and verify the maximum data rate and logic levels in the manufacturer's electrical tables.
推荐
推荐产品汇总
工程参考数据: MAX232MJE/883B ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX232MJE | MAX232EJE | MAX232MJE/883 |
|---|---|---|---|---|
| Package | 16-pin CDIP | 16-pin CDIP | 16-pin CDIP | 16-pin CDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Product Type | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver |
| Supply Voltage | +5 V | +5 V | +5 V | +5 V |
| Transmitters | 2 | 2 | 2 | 2 |
| Receivers | 2 | 2 | 2 | 2 |
| Interface Standard | EIA/TIA-232E | EIA/TIA-232E | EIA/TIA-232E | EIA/TIA-232E |
| Grade or Screening Designation | /883B | Base grade | E grade | /883 |
关键差异点
- Screened /883B ordering designation for procurement-aware assemblies (对比 MAX232MJE)
- Retains the same CDIP footprint as the base MAX232 (对比 MAX232EJE)
- Single-rail interface simplifies embedded serial links (对比 MAX232MJE/883)
设计说明
Place all charge-pump capacitors as close as practical to the MAX232MJE/883B pins identified in the manufacturer pin-description table. Keep each capacitor connection short, symmetrical where the recommended circuit permits, and free of test-point stubs. The switching-capacitor loops should remain compact to limit radiated and conducted noise. Place the local supply bypass capacitor directly between the supply and ground pins rather than routing it around the board.
Separate logic-side nets from cable-side RS-232 nets when laying out the PCB. Route driver outputs directly toward the protection and connector area, and keep receiver inputs away from noisy power circuitry and switching nodes. Maintain a continuous ground reference beneath the device and return cable surge current through a deliberate protection path. This prevents transient current from flowing through sensitive logic traces and reduces susceptibility to communication errors.
Do not treat an RS-232 transceiver as a differential bus and do not interchange it with an RS-485 or RS-422 device. RS-232 is single-ended, and correct operation depends on signal polarity, reference ground, cable configuration, and the connected equipment's voltage levels. Before releasing a replacement, verify every receiver and transmitter connection, the required charge-pump capacitors, supply bypassing, temperature grade, and the qualification status of the exact ordering code.
合规信息
The MAX232 family documentation identifies EIA/TIA-232E, V.28, and V.24 interface requirements. Product-specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the available catalog excerpts.