Texas Instruments

MAX3232ECDWG4 - 3 to 5.5V Dual RS-232 Transceiver | Texas Instruments

Référence : MAX3232ECDWG4 ✓ Actif
3 V to 5.5 V Vdss 16-SOIC, 0.295 inch body width Package
MOQ : 1 |

MAX3232ECDWG4 Présentation

The Texas Instruments MAX3232ECDWG4 is a 3 V to 5.5 V RS-232 line transceiver with two transmitters, two receivers, a dual charge-pump circuit, and ±15 kV IEC ESD protection, packaged in a 16-pin SOIC. The MAX3232ECDWG4 provides the electrical interface between RS-232 ports and CMOS-compatible microcontroller or FPGA logic while supporting commercial-temperature operation.

An RS-232 transceiver is an interface IC that converts between single-ended, bipolar RS-232 signals and lower-voltage logic signals. The MAX3232ECDWG4 belongs to the RS-232 transceiver hierarchy, where it bridges a communications port on one side and a host controller on the other. Its integrated charge pumps generate the positive and negative voltages required to transmit RS-232 levels without a separate external supply.

The device operates from 3 V to 5.5 V and includes two drivers and two receivers. Pin-to-pin ESD protection is rated at ±15 kV using the IEC contact-discharge and air-gap-discharge criteria identified for the MAX3232E family. Additional operating features include low-power operation, short-circuit protection, and compatibility with TIA/EIA-232-F interface requirements.

Technically, the dual charge-pump architecture supports both RS-232 directions while reducing the external component count required for level translation. The transmitters convert CMOS logic into RS-232 signal levels, while the receivers detect and convert incoming RS-232 levels into CMOS-compatible signals. This integration is useful where a system needs reliable serial-console, point-to-point, or equipment-control connectivity without using a full UART physical-layer solution with additional external support circuitry.

Typical applications include industrial serial adapters, instrumentation, data-acquisition equipment, embedded control panels, and debug or programming interfaces connected to microcontrollers and FPGAs. The 3 V to 5.5 V supply range allows operation alongside both 3.3 V and 5 V digital systems. Commercial temperature grade and tube packaging support conventional industrial and consumer manufacturing processes.

For PCB design, place the charge-pump capacitors and the interface-side capacitors close to their associated pins, keep the RS-232 connector path away from sensitive clocks and analog inputs, and provide a low-impedance ground return between connected equipment. Cable transients still require system-level protection when exposed to severe industrial or outdoor environments.

This page combines device specifications, practical PCB guidance, sourcing information, and a qualified drop-in comparison to help engineers evaluate the MAX3232ECDWG4 for new designs and controlled replacement programs.

Alternatives de remplacement direct pour MAX3232ECDWG4 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

MAX3232EIDR

✅ Remplacement direct
Texas Instruments
📦 16-SOIC
Dual RS-232 line driver/receiver transceiver · 2 drivers · 2 receivers · 250 kbps · 3 V to 5.5 V · 3.3 V · RS-232 · ±15 kV

Contactez-nous pour le prix

Voir la fiche technique →

MAX3232ECDWG4 Spécifications

Product Type RS-232 line transceiver
Number of Drivers 2
Number of Receivers 2
Supply Voltage Range 3 V to 5.5 V
Protocol RS-232
Interface Standard TIA/EIA-232-F
ESD Protection ±15 kV IEC contact discharge and air-gap discharge
Boîtier 16-SOIC, 0.295 inch body width
Package Body Width 0.295 inch (7.50 mm)
Number of Terminals 16
Type de montage Surface mount
Packaging Tube
Temperature Grade Commercial
Lead-Free Status Lead-free
Charge-Pump Circuit Dual
Operating Mode Full duplex
Short-Circuit Protection Yes

Guide de configuration des broches du MAX3232ECDWG4 0.295 inch (7.50 mm)

Configuration des broches du MAX3232ECDWG4 (boîtier 0.295 inch (7.50 mm)). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.

Schéma de brochage du boîtier 0.295 inch (7.50 mm) pour le MAX3232ECDWG4

Aucune donnée de brochage détaillée disponible pour MAX3232ECDWG4.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

MAX3232ECDWG4 convient pour 6 applications: Microcontroller Serial Console, Industrial Data-Acquisition Equipment, FPGA Communication Adapter, Instrumentation Control Interface, Embedded Control Panel, Point-to-Point Equipment Link.

🔧

Microcontroller Serial Console

The MAX3232ECDWG4 fits a microcontroller debug console that requires a physical RS-232 port. Its two transmitters and two receivers support full-duplex point-to-point communication, while the integrated dual charge-pump circuit generates the required RS-232 voltage levels from a 3 V to 5.5 V supply. A 3.3 V microcontroller can therefore use the transceiver as a logic-level bridge without adding a separate bipolar supply. The interface also includes short-circuit protection, and its ±15 kV IEC ESD rating strengthens protection against normal cable-contact events. Place the charge-pump capacitors close to the IC and connect the bus-side network according to the manufacturer application circuit.

🏭

Industrial Data-Acquisition Equipment

The MAX3232ECDWG4 is useful in industrial data-acquisition equipment that exposes a legacy RS-232 configuration port alongside a modern digital controller. Its 3 V to 5.5 V operating range allows common rail compatibility with embedded processors, while full-duplex operation supports simultaneous command transmission and status reception. The commercial temperature grade matches ordinary indoor industrial equipment, although harsher ambient conditions may require a wider-temperature ordering option. The integrated dual charge-pump design reduces external circuitry, and ±15 kV IEC bus-pin ESD protection improves robustness when users connect and disconnect field cables.

🖥️

FPGA Communication Adapter

The MAX3232ECDWG4 can provide an RS-232 port for an FPGA-based communication adapter when the FPGA lacks a compatible multi-voltage serial interface. The device accepts CMOS-compatible logic levels and converts them into TIA/EIA-232-F-compatible bus signals through its integrated charge pumps. Two transmitters and two receivers make it suitable for full-duplex links carrying commands, status, configuration data, or diagnostic records. Because the FPGA supply can be 3.3 V, the transceiver's 3 V minimum operating voltage allows shared regulation without level translation on the logic side. Short-circuit protection helps contain faults if an external RS-232 driver drives a conflicting level.

📺

Instrumentation Control Interface

The MAX3232ECDWG4 is appropriate for laboratory and test instruments that use RS-232 to exchange commands with a host computer or controller. Its full-duplex 2/2 driver-receiver arrangement supports continuous bidirectional traffic, and the integrated dual charge-pump circuit provides the bipolar RS-232 interface from a single 3 V to 5.5 V source. The TIA/EIA-232-F qualification cited by the manufacturer supports use as the physical interface between asynchronous control circuitry and an RS-232 port. Place the device near the connector or entry point, maintain a short ground return, and keep the protected bus path separated from sensitive measurement circuitry.

🧩

Embedded Control Panel

The MAX3232ECDWG4 can serve as the RS-232 link in an embedded control panel that exchanges configuration and diagnostic data with a host system. Its dual transmitters and dual receivers allow full-duplex operation, while the 3 V to 5.5 V supply range supports integration with common embedded-controller voltages. The integrated charge-pump implementation reduces the number of external support components, which is valuable when the board must fit a compact enclosure and route through a crowded connector area. The ±15 kV IEC ESD protection is particularly useful for a panel connector exposed to user-accessible cabling. Maintain short bus traces and a continuous chassis or signal-ground return to limit common-mode effects.

🌐

Point-to-Point Equipment Link

The MAX3232ECDWG4 is suited to point-to-point equipment links where two systems require RS-232 signaling over a cable. The device provides separate transmit and receive channels for full-duplex communication and uses an integrated dual charge-pump circuit to develop the required RS-232 levels from a single low-voltage supply. Its commercial temperature grade is appropriate for indoor equipment operating within the specified commercial environment. The transceiver's short-circuit protection reduces the risk of damage from an incorrectly wired or conflicting cable. For longer or electrically noisy installations, evaluate the complete interface against the manufacturer's recommended capacitor network and add external surge protection where the cable environment exceeds the device's rated ESD exposure.

What is the MAX3232ECDWG4?
The MAX3232ECDWG4 is a dual-transmitter, dual-receiver RS-232 transceiver from Texas Instruments. According to the manufacturer datasheet, it operates from 3 V to 5.5 V, uses an integrated dual charge-pump circuit, provides ±15 kV IEC ESD protection on the RS-232 bus pins, and is packaged in a 16-pin SOIC. The device converts between RS-232 signal levels and CMOS-compatible logic used by microcontrollers, FPGAs, and other digital controllers.
What are the key specifications of MAX3232ECDWG4 that engineers should know?
The MAX3232ECDWG4 is a 16-SOIC RS-232 interface IC with 2 transmitters, 2 receivers, a 3 V to 5.5 V supply range, and ±15 kV IEC ESD protection. According to the manufacturer datasheet, it includes a dual charge-pump circuit, supports full-duplex operation, provides short-circuit protection, and meets TIA/EIA-232-F interface requirements. Its commercial temperature grade and tube packaging are intended for conventional surface-mount assembly and industrial or consumer equipment.
What is the operating voltage of MAX3232ECDWG4?
The MAX3232ECDWG4 operates from 3 V to 5.5 V. According to the manufacturer datasheet, this range supports both 3.3 V and 5 V systems, allowing the RS-232 transceiver to share a regulated supply with many microcontrollers, FPGAs, and digital interface controllers. The charge-pump circuitry generates the positive and negative signal levels required by RS-232 transmitters internally, so the external logic supply does not need to provide those bipolar bus voltages.
Where can I download the MAX3232ECDWG4 datasheet PDF?
The MAX3232ECDWG4 datasheet is available through the Texas Instruments product page and the manufacturer datasheet archive. The document covers the electrical characteristics, charge-pump circuit, RS-232 driver and receiver behavior, ESD ratings, recommended operating conditions, and the 16-pin pin configuration. Use the manufacturer's pin-description table when assigning PCB nets because several pins participate in the charge-pump and receiver timing networks.
Where can I find the MAX3232ECDWG4 pinout?
The MAX3232ECDWG4 pinout is documented in the manufacturer datasheet as a 16-pin SOIC arrangement. Use the pin-description table and land-pattern drawing from that document when laying out the PCB, and follow the package drawing for pin 1 orientation. The MAX3232ECDWG4 also contains charge-pump and receiver timing components whose external capacitors must be connected according to the datasheet's typical application circuit.
Does MAX3232ECDWG4 provide ESD protection?
Yes. The MAX3232ECDWG4 provides ±15 kV IEC ESD protection on the RS-232 bus pins, including the ground connection identified in the device documentation. According to the manufacturer datasheet, the protection is specified under IEC contact-discharge and air-gap-discharge conditions. This rating reduces risk from cable insertion and routine ESD events, although the final equipment may still require external surge protection for severe industrial transients.
Where can I buy MAX3232ECDWG4 and request a quote?
The MAX3232ECDWG4 can be requested through XAIPART's Request a Quote form on this page. The form is the appropriate route for current commercial terms, quantity availability, and lead-time confirmation because transaction details can change. The device is a 16-pin SOIC RS-232 transceiver supplied in tube packaging, and buyers should state their required quantity and any reel or production-packaging needs when submitting the request.
What is the price of MAX3232ECDWG4?
Current commercial pricing for the MAX3232ECDWG4 is handled through XAIPART's Request a Quote form on this page. Quote requests are preferable to static price statements because component pricing, inventory, and lead time can change independently of a product page. Submit the required quantity and target packaging details so the current offer can reflect the exact MAX3232ECDWG4 ordering configuration.
What is the lead time for MAX3232ECDWG4?
The current lead time for MAX3232ECDWG4 should be confirmed through XAIPART's Request a Quote form on this page. Lead time can vary with order quantity, production scheduling, and packaging requirements. The component is identified as a Texas Instruments 16-pin SOIC RS-232 transceiver supplied in a tube, so include any scheduled-build requirements in the request when asking for a delivery commitment.
Is MAX3232ECDWG4 in stock?
Current stock for MAX3232ECDWG4 should be checked through XAIPART's Request a Quote form on this page. The form provides a direct path for confirming quantity availability and expected delivery for the requested configuration. Because inventory is time-sensitive, do not base a production schedule on a cached listing or a general availability statement; request confirmation for the quantity and packaging plan your assembly operation requires.
What is the difference between MAX3232ECDWG4 and MAX3232EIDR?
The MAX3232EIDR is a temperature-grade alternative within the MAX3232E family, while the MAX3232ECDWG4 is identified as a commercial-grade, 16-SOIC, tube-packaged device. According to the manufacturer comparison information, the MAX3232E provides the same basic RS-232 interface function and is an improved direct drop-in replacement for the original MAX3232. Confirm package dimensions, temperature limits, and ordering codes before approving either part for a specific production release.
When should I choose MAX3232ECDWG4 over MAX3232EIDR?
Choose MAX3232ECDWG4 when the design operates within commercial-temperature conditions and can use the 16-pin SOIC tube-packaged configuration. Choose the industrial-temperature MAX3232EIDR option when the equipment must operate across a wider environmental range. Both devices belong to the MAX3232E family, so the decision should be based on verified temperature ratings, package fit, lead time, and lifecycle availability rather than assuming every ordering suffix is interchangeable.
Is MAX3232ECDWG4 suitable for a microcontroller RS-232 interface?
The MAX3232ECDWG4 is suitable for a 3.3 V or 5 V microcontroller RS-232 interface because it combines two transmitters, two receivers, and the required dual charge-pump circuitry. According to the manufacturer datasheet, it meets TIA/EIA-232-F interface requirements and includes short-circuit protection. Connect the MCU UART logic signals to the receiver and driver logic pins, and connect the bus-side pins through the datasheet-recommended network to the RS-232 connector.
What can replace MAX3232ECDWG4?
The qualified drop-in replacement shown for MAX3232ECDWG4 is the MAX3232EIDR, which shares the 16-pin SOIC package and MAX3232E-family RS-232 function. Texas Instruments identifies MAX3232E as an improved direct drop-in replacement for MAX3232, while the ETEI comparison documents the relationship between MAX3232EIDR and MAX3232ECDWG4. Validate temperature grade and production suitability before substitution, even when the land pattern is unchanged.
What is the best cross-brand equivalent for MAX3232ECDWG4?
No cross-brand equivalent is established as a verified drop-in replacement in the available cross-reference information. The documented replacement path is the same-manufacturer MAX3232EIDR, and the Texas Instruments comparison identifies MAX3232E as the improved direct replacement for MAX3232. A different manufacturer's RS-232 transceiver should be considered only after checking its 16-pin SOIC footprint, charge-pump capacitor values, logic thresholds, ESD rating, and propagation behavior against the original design.
How should MAX3232ECDWG4 be laid out on a PCB?
Place all charge-pump and receiver timing capacitors close to their designated IC pins, and route the RS-232 bus signals directly toward the connector without unnecessary stubs. According to the manufacturer application guidance, the capacitor values and connection topology shown in the typical application circuit are part of the specified interface behavior. Keep the bus path away from clocks, reset lines, and sensitive analog inputs, and provide a short, low-impedance ground return between connected systems.

Données de référence d'ingénierie pour MAX3232ECDWG4 — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose MAX3232ECDWG4 for a commercial-temperature, 3 V to 5.5 V RS-232 interface using a 16-pin SOIC and tube-packaged parts. It is especially appropriate when the design needs two transmitters, two receivers, integrated dual charge pumps, and ±15 kV IEC bus-pin ESD protection. Select MAX3232EIDR when the same pin-compatible family is needed for an industrial-temperature environment or a different production ordering route. Before replacing either device, verify the ordering suffix, package drawing, operating-temperature limits, and lifecycle status. A cross-brand RS-232 transceiver should not be treated as a drop-in option without confirming the footprint, external capacitor values, logic thresholds, ESD rating, and receiver timing behavior.

Comparaison avec les alternatives

Paramètre Ce produit MAX3232EIDR
Brand Texas Instruments Texas Instruments
Package 16-SOIC 16-SOIC - same package
Device Type RS-232 transceiver RS-232 transceiver
Number of Drivers 2 2
Number of Receivers 2 2
Temperature Grade Commercial Industrial
Charge-Pump Circuit Dual Dual
Interface Standard TIA/EIA-232-F TIA/EIA-232-F

Principaux différenciateurs

  • Commercial-grade choice with integrated dual charge pumps (vs MAX3232EIDR)
  • Complete RS-232 interface in one 16-pin package (vs MAX3232EIDR)
  • Specified bus-pin ESD resilience (vs MAX3232EIDR)

Notes de conception

Place the charge-pump capacitors and the receiver timing capacitors close to their specified MAX3232ECDWG4 pins. Keep the RS-232 traces short, avoid test-point stubs on the bus side, and route the interface away from clocks, ADC inputs, and other noise-sensitive nets. Connect the transceiver ground directly to the equipment signal ground and provide a low-impedance return path to the RS-232 connector. The external capacitor values and network topology should follow the manufacturer application circuit.

Do not treat the logic supply as the RS-232 bus voltage. The MAX3232ECDWG4 uses its dual charge pumps to generate the positive and negative levels required at the transmitter outputs. Likewise, do not omit the receiver timing components, because they form part of the specified receiver behavior. Verify that connector pin assignments match driver and receiver orientation before power-up, and check that any attached equipment uses compatible RS-232 levels and grounding.

For cables leaving an enclosure, keep the protected RS-232 interface near the connector and provide a defined chassis-to-signal-ground strategy. The ±15 kV IEC rating addresses specified ESD conditions, but it does not eliminate the need for coordinated surge and common-mode protection in severe industrial environments. Verify the complete cable path, connector shell bonding, and enclosure grounding rather than assuming the IC rating alone controls conducted or radiated emissions.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Yes
Sans halogène
Unknown
Minerais de conflit
Unknown

The MAX3232ECDWG4 listing identifies the device as lead-free. RoHS, REACH, halogen-free, and conflict-minerals status require confirmation from the manufacturer or current product documentation.

Données vérifiées le : 2026-11-09 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

MAX3232ECDWG4 datasheet MAX3232ECDWG4 datasheet pdf MAX3232ECDWG4 pinout MAX3232ECDWG4 equivalent MAX3232ECDWG4 replacement MAX3232ECDWG4 cross reference Texas Instruments MAX3232ECDWG4 MAX3232ECDWG4 16-SOIC MAX3232ECDWG4 RS-232 transceiver MAX3232ECDWG4 3 to 5.5V MAX3232ECDWG4 ESD protection MAX3232ECDWG4 price MAX3232ECDWG4 stock MAX3232ECDWG4 vs MAX3232EIDR MAX3232ECDWG4 application circuit

Composants & termes associés

Texas Instruments MAX3232ECDWG4 MAX3232EIDR RS-232 transceiver line driver line receiver RS-232 interface IC CMOS logic dual charge-pump circuit TIA/EIA-232-F IEC 61000-4-2 ESD protection 3 V to 5.5 V power supply 16-SOIC SOIC package family surface-mount package full-duplex serial communication microcontroller UART FPGA interface industrial instrumentation data-acquisition equipment embedded control panel commercial temperature grade
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ