MAX3232ECDWG4 - 3 to 5.5V Dual RS-232 Transceiver | Texas Instruments
MPN: MAX3232ECDWG4 ✓ AktifMAX3232ECDWG4 Genel Bakış
An RS-232 transceiver is an interface IC that converts between single-ended, bipolar RS-232 signals and lower-voltage logic signals. The MAX3232ECDWG4 belongs to the RS-232 transceiver hierarchy, where it bridges a communications port on one side and a host controller on the other. Its integrated charge pumps generate the positive and negative voltages required to transmit RS-232 levels without a separate external supply.
The device operates from 3 V to 5.5 V and includes two drivers and two receivers. Pin-to-pin ESD protection is rated at ±15 kV using the IEC contact-discharge and air-gap-discharge criteria identified for the MAX3232E family. Additional operating features include low-power operation, short-circuit protection, and compatibility with TIA/EIA-232-F interface requirements.
Technically, the dual charge-pump architecture supports both RS-232 directions while reducing the external component count required for level translation. The transmitters convert CMOS logic into RS-232 signal levels, while the receivers detect and convert incoming RS-232 levels into CMOS-compatible signals. This integration is useful where a system needs reliable serial-console, point-to-point, or equipment-control connectivity without using a full UART physical-layer solution with additional external support circuitry.
Typical applications include industrial serial adapters, instrumentation, data-acquisition equipment, embedded control panels, and debug or programming interfaces connected to microcontrollers and FPGAs. The 3 V to 5.5 V supply range allows operation alongside both 3.3 V and 5 V digital systems. Commercial temperature grade and tube packaging support conventional industrial and consumer manufacturing processes.
For PCB design, place the charge-pump capacitors and the interface-side capacitors close to their associated pins, keep the RS-232 connector path away from sensitive clocks and analog inputs, and provide a low-impedance ground return between connected equipment. Cable transients still require system-level protection when exposed to severe industrial or outdoor environments.
This page combines device specifications, practical PCB guidance, sourcing information, and a qualified drop-in comparison to help engineers evaluate the MAX3232ECDWG4 for new designs and controlled replacement programs.
Drop-in alternatifler için MAX3232ECDWG4 — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
MAX3232EIDR
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →MAX3232ECDWG4 Özellikler
| Product Type | RS-232 line transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Supply Voltage Range | 3 V to 5.5 V |
| Protocol | RS-232 |
| Interface Standard | TIA/EIA-232-F |
| ESD Protection | ±15 kV IEC contact discharge and air-gap discharge |
| Paket | 16-SOIC, 0.295 inch body width |
| Package Body Width | 0.295 inch (7.50 mm) |
| Number of Terminals | 16 |
| Montaj Türü | Surface mount |
| Packaging | Tube |
| Temperature Grade | Commercial |
| Lead-Free Status | Lead-free |
| Charge-Pump Circuit | Dual |
| Operating Mode | Full duplex |
| Short-Circuit Protection | Yes |
MAX3232ECDWG4 0.295 inch (7.50 mm) Pin Yapısı Kılavuzu
MAX3232ECDWG4 (0.295 inch (7.50 mm) paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: MAX3232ECDWG4.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
MAX3232ECDWG4 için uygundur 6 uygulamas: Microcontroller Serial Console, Industrial Data-Acquisition Equipment, FPGA Communication Adapter, Instrumentation Control Interface, Embedded Control Panel, Point-to-Point Equipment Link.
Microcontroller Serial Console
The MAX3232ECDWG4 fits a microcontroller debug console that requires a physical RS-232 port. Its two transmitters and two receivers support full-duplex point-to-point communication, while the integrated dual charge-pump circuit generates the required RS-232 voltage levels from a 3 V to 5.5 V supply. A 3.3 V microcontroller can therefore use the transceiver as a logic-level bridge without adding a separate bipolar supply. The interface also includes short-circuit protection, and its ±15 kV IEC ESD rating strengthens protection against normal cable-contact events. Place the charge-pump capacitors close to the IC and connect the bus-side network according to the manufacturer application circuit.
Industrial Data-Acquisition Equipment
The MAX3232ECDWG4 is useful in industrial data-acquisition equipment that exposes a legacy RS-232 configuration port alongside a modern digital controller. Its 3 V to 5.5 V operating range allows common rail compatibility with embedded processors, while full-duplex operation supports simultaneous command transmission and status reception. The commercial temperature grade matches ordinary indoor industrial equipment, although harsher ambient conditions may require a wider-temperature ordering option. The integrated dual charge-pump design reduces external circuitry, and ±15 kV IEC bus-pin ESD protection improves robustness when users connect and disconnect field cables.
FPGA Communication Adapter
The MAX3232ECDWG4 can provide an RS-232 port for an FPGA-based communication adapter when the FPGA lacks a compatible multi-voltage serial interface. The device accepts CMOS-compatible logic levels and converts them into TIA/EIA-232-F-compatible bus signals through its integrated charge pumps. Two transmitters and two receivers make it suitable for full-duplex links carrying commands, status, configuration data, or diagnostic records. Because the FPGA supply can be 3.3 V, the transceiver's 3 V minimum operating voltage allows shared regulation without level translation on the logic side. Short-circuit protection helps contain faults if an external RS-232 driver drives a conflicting level.
Instrumentation Control Interface
The MAX3232ECDWG4 is appropriate for laboratory and test instruments that use RS-232 to exchange commands with a host computer or controller. Its full-duplex 2/2 driver-receiver arrangement supports continuous bidirectional traffic, and the integrated dual charge-pump circuit provides the bipolar RS-232 interface from a single 3 V to 5.5 V source. The TIA/EIA-232-F qualification cited by the manufacturer supports use as the physical interface between asynchronous control circuitry and an RS-232 port. Place the device near the connector or entry point, maintain a short ground return, and keep the protected bus path separated from sensitive measurement circuitry.
Embedded Control Panel
The MAX3232ECDWG4 can serve as the RS-232 link in an embedded control panel that exchanges configuration and diagnostic data with a host system. Its dual transmitters and dual receivers allow full-duplex operation, while the 3 V to 5.5 V supply range supports integration with common embedded-controller voltages. The integrated charge-pump implementation reduces the number of external support components, which is valuable when the board must fit a compact enclosure and route through a crowded connector area. The ±15 kV IEC ESD protection is particularly useful for a panel connector exposed to user-accessible cabling. Maintain short bus traces and a continuous chassis or signal-ground return to limit common-mode effects.
Point-to-Point Equipment Link
The MAX3232ECDWG4 is suited to point-to-point equipment links where two systems require RS-232 signaling over a cable. The device provides separate transmit and receive channels for full-duplex communication and uses an integrated dual charge-pump circuit to develop the required RS-232 levels from a single low-voltage supply. Its commercial temperature grade is appropriate for indoor equipment operating within the specified commercial environment. The transceiver's short-circuit protection reduces the risk of damage from an incorrectly wired or conflicting cable. For longer or electrically noisy installations, evaluate the complete interface against the manufacturer's recommended capacitor network and add external surge protection where the cable environment exceeds the device's rated ESD exposure.
Mühendislik referans verileri: MAX3232ECDWG4 — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | MAX3232EIDR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 16-SOIC | 16-SOIC - same package |
| Device Type | RS-232 transceiver | RS-232 transceiver |
| Number of Drivers | 2 | 2 |
| Number of Receivers | 2 | 2 |
| Temperature Grade | Commercial | Industrial |
| Charge-Pump Circuit | Dual | Dual |
| Interface Standard | TIA/EIA-232-F | TIA/EIA-232-F |
Ana Farklılayıcılar
- Commercial-grade choice with integrated dual charge pumps (karşılaştırma:MAX3232EIDR)
- Complete RS-232 interface in one 16-pin package (karşılaştırma:MAX3232EIDR)
- Specified bus-pin ESD resilience (karşılaştırma:MAX3232EIDR)
Tasarım Notları
Place the charge-pump capacitors and the receiver timing capacitors close to their specified MAX3232ECDWG4 pins. Keep the RS-232 traces short, avoid test-point stubs on the bus side, and route the interface away from clocks, ADC inputs, and other noise-sensitive nets. Connect the transceiver ground directly to the equipment signal ground and provide a low-impedance return path to the RS-232 connector. The external capacitor values and network topology should follow the manufacturer application circuit.
Do not treat the logic supply as the RS-232 bus voltage. The MAX3232ECDWG4 uses its dual charge pumps to generate the positive and negative levels required at the transmitter outputs. Likewise, do not omit the receiver timing components, because they form part of the specified receiver behavior. Verify that connector pin assignments match driver and receiver orientation before power-up, and check that any attached equipment uses compatible RS-232 levels and grounding.
For cables leaving an enclosure, keep the protected RS-232 interface near the connector and provide a defined chassis-to-signal-ground strategy. The ±15 kV IEC rating addresses specified ESD conditions, but it does not eliminate the need for coordinated surge and common-mode protection in severe industrial environments. Verify the complete cable path, connector shell bonding, and enclosure grounding rather than assuming the IC rating alone controls conducted or radiated emissions.
Uyumluluk Bilgisi
The MAX3232ECDWG4 listing identifies the device as lead-free. RoHS, REACH, halogen-free, and conflict-minerals status require confirmation from the manufacturer or current product documentation.