MAX3232IDWRG4 - Dual RS-232 Transceiver | Texas Instruments
Référence : MAX3232IDWRG4 ✓ ActifMAX3232IDWRG4 Présentation
An RS-232 transceiver is an interface IC that converts low-voltage logic signals into RS-232 line levels and receives differential bipolar signals, converting them back into CMOS-compatible logic levels. This dual-driver, dual-receiver arrangement places the MAX3232IDWRG4 within the hierarchy of interface ICs, serial transceivers, line drivers and receivers, and data-conversion semiconductors. It is used where a powered system must exchange data with an RS-232 equipment port.
The principal features include two transmit channels, two receive channels, operation from a single 3 V to 5.5 V supply, data rates up to 250 kbps, and ±15 kV ESD protection. The industrial-temperature rating supports equipment operating across extended ambient conditions. These characteristics make the device suitable for industrial controls, test equipment, POS terminals, and embedded systems that communicate with legacy RS-232 peripherals.
The MAX3232 interface architecture uses on-chip level-shifting circuitry to produce the positive and negative voltage swings required by RS-232 while operating from a modern low-voltage supply. Because RS-232 is a point-to-point interface, each transmitter should drive one receiver and the connection should include signal-ground continuity. The 250 kbps capability supports legacy control and diagnostic protocols without requiring a separate line-driver IC.
Typical applications include industrial serial controllers, laboratory test systems, point-of-sale equipment, barcode scanners, and service-console interfaces. In each case, the IC handles the physical RS-232 voltage conversion while the host UART handles framing, parity, and data-rate configuration. The device can therefore simplify board partitioning by combining the driver and receiver functions in one package.
PCB implementation should preserve the required charge-pump capacitors, route each RS-232 line away from sensitive analog signals, and provide a low-impedance ground path between the two connected systems. Confirm the external capacitor values, pin assignments, and maximum driver-load requirements against the manufacturer datasheet before releasing a new layout. The device is a digital interface IC, so a safe operating area curve is not applicable.
This product record combines the manufacturer’s electrical and package specifications, sourcing guidance, practical layout considerations, and same-footprint replacement information. It is intended to help engineers evaluate the MAX3232IDWRG4 for new designs, cross-reference legacy RS-232 interfaces, and plan industrial-temperature production boards.
Alternatives de remplacement direct pour MAX3232IDWRG4 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MAX3232IDWRG4 (même facteur de forme et même empreinte) — différant par ESD Protection, Package, Product Type.
MAX3232EIDWRG4
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX3232ECDW
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MAX3232IDWRG4 Spécifications
| Product Type | Dual RS-232 line driver/receiver |
| Number of Transmit Channels | 2 channels |
| Number of Receive Channels | 2 channels |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection | ±15 kV |
| Plage de température de fonctionnement | -40°C to +85°C |
| Boîtier | 16-pin SOIC (DW) |
| Package Code | DW |
| Terminal Count | 16 pins |
| Type de montage | Surface mount |
| Interface Standard | RS-232 |
Guide de configuration des broches du MAX3232IDWRG4 dw
Configuration des broches du MAX3232IDWRG4 (boîtier dw). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour MAX3232IDWRG4.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MAX3232IDWRG4 convient pour 6 applications: Industrial Serial Control Interface, Point-of-Sale Terminal Interface, Barcode Scanner and Reader Integration, Laboratory Test and Measurement Equipment, Embedded Service and Configuration Console, Building and Automation Controller.
Industrial Serial Control Interface
The MAX3232IDWRG4 is well suited to industrial controllers that must communicate with legacy RS-232 equipment over a point-to-point cable. Its 3 V to 5.5 V operating range permits connection to 3.3 V or 5 V control electronics, while the two transmitter and two receiver channels support bidirectional console or service links. The industrial -40°C to +85°C rating supports controlled machinery and factory equipment. A practical design places the transceiver beside the DB9 or equivalent connector, uses the manufacturer-recommended charge-pump capacitors, and routes each signal away from switching and analog circuitry.
Point-of-Sale Terminal Interface
A point-of-sale terminal can use the MAX3232IDWRG4 to bridge its host UART to an RS-232 peripheral such as a scanner, printer, or customer display. The integrated dual-driver and dual-receiver arrangement reduces the number of separate interface components on the board, while the 250 kbps rate covers common serial-control protocols. Operating from 3.3 V or 5 V also supports two prevalent embedded-compute supply rails. The implementation should preserve point-to-point RS-232 topology, provide signal-ground continuity, and place protection or filtering close to the external connector.
Barcode Scanner and Reader Integration
The MAX3232IDWRG4 can interface an RS-232 barcode scanner with an embedded controller while leaving the controller UART free to exchange commands and decoded data. Its two receive channels allow one port to monitor two compatible devices, although each RS-232 transmitter should have only one receiver because the interface is point-to-point. The 3 V to 5.5 V supply range supports embedded logic rails, and ±15 kV ESD protection adds useful margin on externally connected scanner cables. Correct connector grounding and controlled cable routing remain essential for reliable operation.
Laboratory Test and Measurement Equipment
RS-232 remains common on laboratory instruments for remote commands, measurement transfer, and diagnostic functions. The MAX3232IDWRG4 provides two 250 kbps channels in a compact 16-pin SOIC package, allowing a test instrument to expose a legacy serial port without requiring a separate driver and receiver. Its -40°C to +85°C operating range supports controlled test environments. Engineers should use the manufacturer application circuit for charge-pump capacitance and verify line-driver loading, cable length, and grounding under the expected instrument configuration.
Embedded Service and Configuration Console
The MAX3232IDWRG4 is suitable for embedded systems that expose a service port for configuration, firmware download, or diagnostic logs. A 3.3 V or 5 V system can operate the transceiver directly, and the two receive channels can support one primary data link plus a hardware-status input where the RS-232 levels are compatible. The 250 kbps maximum data rate accommodates many low-bandwidth service protocols. The board design should isolate the external serial connector from sensitive circuitry, use a defined chassis or signal ground, and include the required charge-pump capacitors close to the device.
Building and Automation Controller
Building automation controllers can use the MAX3232IDWRG4 to connect service tools, sensors, or access-control equipment that retains an RS-232 interface. The dual-channel architecture supports paired transmit and receive paths, while the 3 V to 5.5 V supply range fits common embedded control platforms. Its extended -40°C to +85°C range is useful in equipment rooms and industrial enclosures, although local self-heating must remain within the device rating. A robust implementation should use twisted-pair wiring where applicable, retain ground continuity, and follow the manufacturer’s recommended PCB layout for the charge-pump network.
Données de référence d'ingénierie pour MAX3232IDWRG4 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MAX3232EIDWRG4 | MAX3232ECDW |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-pin SOIC (DW) | 16-pin SOIC (DW) | 16-pin SOIC (DW) |
| Product Type | Dual RS-232 line driver/receiver | Dual RS-232 line driver/receiver | Dual RS-232 line driver/receiver |
| Transmit Channels | 2 channels | 2 channels | 2 channels |
| Receive Channels | 2 channels | 2 channels | 2 channels |
| Mounting Type | Surface mount | Surface mount | Surface mount |
Principaux différenciateurs
- Exact original MAX3232 configuration for existing industrial designs (vs MAX3232EIDWRG4)
- Manufacturer-recommended improved family option (vs MAX3232IDWRG4)
- Integrated dual-channel interface reduces separate IC count (vs MAX3232ECDW)
Notes de conception
Place the charge-pump capacitors and required supply bypass capacitor directly beside their associated MAX3232IDWRG4 pins, using the shortest possible traces. Keep the external connector and protection network at the board edge, while placing the transceiver nearer the logic controller. This separation helps prevent electrostatic-discharge and cable-transient energy from propagating into sensitive circuitry and reduces the loop area of the switching charge-pump nodes.
Route each RS-232 signal as a point-to-point conductor with a corresponding signal-ground return where practical. Keep the two transceiver channels physically separated to reduce crosstalk, and avoid running RS-232 traces beside switching regulators, clock lines, or sensitive analog inputs. Use a solid ground reference beneath the interface section, and terminate unused inputs according to the manufacturer guidance rather than allowing them to float.
Do not treat a matching SOIC-16 footprint as sufficient proof of interchangeability. Confirm the complete pin functions, charge-pump capacitor values, supply limits, receiver thresholds, driver load, temperature grade, and ESD rating for the exact ordering code. RS-232 is point-to-point, so do not connect one driver output to multiple receiver inputs without an approved switching or distribution arrangement.
Informations de conformité
The manufacturer identifies ±15 kV ESD protection and an industrial operating temperature range, but the reviewed product records do not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status.