MAX3243ECPWR - 3/5 RS-232 Transceiver | Texas Instruments
Référence : MAX3243ECPWR ✓ ActifMAX3243ECPWR Présentation
An RS-232 transceiver is an interface IC that translates logic-level signals between a host or embedded controller and the bipolar, positive and negative signal domain used by serial ports. Within the interface hierarchy, it belongs to the RS-232 transceiver and multi-channel line-driver/receiver family, providing the physical interface between an asynchronous communication controller and a connected data terminal or data communications equipment.
The MAX3243ECPWR provides TIA/EIA-232-F compliant operation, allowing it to interface with conventional RS-232 ports while operating from a modern 3 V or 5 V supply. Its ±15 kV human-body-model and air-gap discharge protection ratings strengthen the serial connector path against electrostatic discharge. The protected serial-port pins also support ±8 kV IEC 61000-4-2 contact-discharge protection.
The integrated dual charge-pump circuit supports both transmitter and receiver operation without a separate external negative supply. Internal voltage conversion produces the bipolar levels required for RS-232 signaling while keeping the system power architecture simple. The three transmitters support connection to multiple data channels, while the five receivers can monitor additional lines such as modem-control or status signals.
Typical applications include industrial serial gateways, point-of-sale equipment, test instruments, industrial control panels, and embedded systems that require RS-232 compatibility with 3 V or 5 V logic. The five-receiver arrangement is useful in designs where the host must inspect handshake, control, or status lines in addition to transmitting on one or more data channels. The device is also appropriate for legacy peripheral connections that predate universal serial bus.
PCB design should place charge-pump capacitors close to their associated pins, provide a continuous ground return for every transceiver connection, and route exposed serial traces away from sensitive analog circuitry. Input and logic-side decoupling should follow the capacitor guidance in the manufacturer datasheet. Connector protection may still be required when cables extend beyond the enclosure or connect to unknown external equipment.
This page combines the MAX3243ECPWR interface capabilities, verified package information, engineering alternatives, and practical RS-232 implementation guidance to help designers evaluate footprint compatibility, protection requirements, and multichannel interface needs before circuit-board release.
Alternatives de remplacement direct pour MAX3243ECPWR — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MAX3243ECPWR (même facteur de forme et même empreinte) — différant par Product Type, Supply Voltage Range, Package, Maximum Data Rate, ESD Protection.
MAX3243EIPWR
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MAX3243CPWR
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MAX3243ECPWR Spécifications
| Device Type | 3/5 multichannel RS-232 line driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 500 kbps |
| Number of Drivers | 3 |
| Number of Receivers | 5 |
| Integrated Charge Pumps | 2 |
| HBM and Air-Gap ESD Protection | ±15 kV |
| IEC Contact Discharge Protection | ±8 kV |
| RS-232 Compliance | TIA/EIA-232-F |
| Boîtier | 28-pin TSSOP |
| Type de montage | Surface mount |
| Nombre de broches | 28 pins |
Configuration des broches de MAX3243ECPWR
| Broche 1 | R1OUT — Receiver 1 output |
| Broche 2 | R2OUT — Receiver 2 output |
| Broche 3 | R3OUT — Receiver 3 output |
| Broche 4 | R1IN — Receiver 1 input |
| Broche 5 | R2IN — Receiver 2 input |
| Broche 6 | R3IN — Receiver 3 input |
| Broche 7 | R4IN — Receiver 4 input |
| Broche 8 | R5IN — Receiver 5 input |
| Broche 9 | R4OUT — Receiver 4 output |
| Broche 10 | R5OUT — Receiver 5 output |
| Broche 11 | T1IN — Driver 1 logic input |
| Broche 12 | T2IN — Driver 2 logic input |
| Broche 13 | T3IN — Driver 3 logic input |
| Broche 14 | T1OUT — Driver 1 RS-232 output |
| Broche 15 | T2OUT — Driver 2 RS-232 output |
| Broche 16 | T3OUT — Driver 3 RS-232 output |
| Broche 17 | GND — Ground |
| Broche 18 | VCC — Positive supply input |
| Broche 19 | EN — Receiver enable input |
| Broche 20 | ON — Charge-pump and transmitter enable input |
| Broche 21 | C1+ — Charge-pump flying capacitor positive terminal |
| Broche 22 | C1- — Charge-pump flying capacitor negative terminal |
| Broche 23 | C2+ — Charge-pump flying capacitor positive terminal |
| Broche 24 | C2- — Charge-pump flying capacitor negative terminal |
| Broche 25 | V+ — Positive charge-pump output |
| Broche 26 | V- — Negative charge-pump output |
| Broche 27 | NC — Not connected |
| Broche 28 | NC — Not connected |
Applications typiques
MAX3243ECPWR convient pour 6 applications: Industrial Serial Gateway, Point-of-Sale Terminal, Test and Measurement Instrument, Embedded Legacy Peripheral Interface, Industrial Control Panel, RS-232 Communication Hub.
Industrial Serial Gateway
The MAX3243ECPWR fits an industrial serial gateway that must translate 3.3 V or 5 V controller logic into RS-232 levels while monitoring several handshake or status lines. Its three transmitters can support multiple outbound channels, and its five receivers provide capacity for control signals in addition to data reception. Operation from 3 V to 5.5 V avoids a separate level shifter for common industrial processors. The 28-pin TSSOP also provides a practical surface-mount footprint, although the added channel count requires careful routing of every receiver and driver net.
Recommandé
Point-of-Sale Terminal
The MAX3243ECPWR can support a point-of-sale terminal that communicates with legacy peripherals while also reading equipment status lines. Three drivers allow control of multiple RS-232 functions, and five receivers can monitor responses, acknowledgments, and hardware-handshake signals from attached equipment. Its 3 V to 5.5 V supply range is suitable for systems built around either 3.3 V or 5 V embedded controllers. The ±15 kV HBM and air-gap protection ratings improve robustness at the serial connector, while the 500 kbps capability covers the data rates normally encountered in peripheral communication.
Recommandé
Test and Measurement Instrument
The MAX3243ECPWR is useful in test and measurement equipment that must provide several RS-232 control and status channels from one interface IC. The three transmitters can drive separate commands or instrument resources, while five receivers allow the controller to read ready, fault, trigger, and response signals. Its 500 kbps maximum data rate supports conventional asynchronous RS-232 control traffic and avoids using several two-channel transceivers. Designers should still place the charge-pump capacitors close to the device and maintain a low-impedance ground path to minimize noise and improve signal integrity.
Recommandé
Embedded Legacy Peripheral Interface
The MAX3243ECPWR provides a direct path from modern embedded-controller I/O to legacy RS-232 peripherals without a separate negative supply. The device accepts a 3 V to 5.5 V supply and internally generates bipolar RS-232 levels with its dual charge-pump circuit. Three drivers and five receivers cover both primary data paths and auxiliary control lines, making the part suitable for industrial controllers, service equipment, and configuration interfaces. The 28-pin TSSOP package reduces board area, but engineers should assign all pins from the MAX3243E pin-description table and account for connector-level surge protection.
Recommandé
Industrial Control Panel
The MAX3243ECPWR can connect an industrial controller to local operator panels, service terminals, and status displays that retain RS-232 connectivity. Five receiver channels provide enough parallel inputs for acknowledge, alarm, and equipment-state signals, while three driver channels support command and control outputs. Its broad 3 V to 5.5 V supply range accommodates both 3.3 V control hardware and 5 V legacy interfaces. The enhanced ESD ratings are particularly relevant when panel wiring leaves the protected enclosure, although long cable routes may require additional surge and surge-protection components.
Recommandé
RS-232 Communication Hub
The MAX3243ECPWR can serve as the central interface in a small RS-232 communication hub linking a host controller to several legacy devices. The three transmitters support outbound connections to different peripherals, while the five receivers allow the hub to observe multiple acknowledgments and control signals. A maximum rate of 500 kbps accommodates typical asynchronous equipment-control traffic. Because the device supports a 3 V minimum supply, it can operate alongside modern 3.3 V processors without adding another regulator. PCB routing should separate connector-side nets from sensitive logic and provide short, symmetrical charge-pump connections.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MAX3243ECPWR — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MAX3243EIPWR | MAX3243CPWR |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP |
| Device Type | 3/5 multichannel RS-232 transceiver | 3/5 multichannel RS-232 transceiver | 3/5 multichannel RS-232 transceiver |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 500 kbps | 500 kbps | 250 kbps |
| Number of Drivers | 3 | 3 | 3 |
| Number of Receivers | 5 | 5 | 5 |
| Integrated Charge Pumps | 2 | 2 | 2 |
Principaux différenciateurs
- Higher listed maximum data rate (vs MAX3243CPWR)
- Enhanced serial-port ESD protection (vs MAX3243CPWR)
- Five receivers support richer control-line monitoring (vs MAX3232IPWR)
Notes de conception
Place both charge-pump capacitors directly between the specified C1 and C2 terminals, with short traces and a nearby ground return. Keep the V+ and V- charge-pump outputs away from sensitive receiver inputs. Follow the pin numbers in the MAX3243E datasheet exactly because the MAX3243C alternative shares the package but may not present every enable function in the same way.
Do not treat the ±15 kV device rating as proof that the complete connector path is surge protected. Internal ESD protection covers specified pins under defined test conditions, while cable transients, long wiring, and ground offsets may require external protection. Confirm which pins are protected and preserve the recommended input, ground, and bypass-capacitor connections from the manufacturer application circuit.
Maintain a low-impedance, continuous ground plane beneath and around the transceiver so receiver thresholds are not shifted by return current. Route each RS-232 driver output directly toward its connector without long stubs. Where a cable is long or the ground path is uncertain, reduce the data rate, verify signal polarity, and evaluate the effect of accumulated cable capacitance on edge shape.
Informations de conformité
The manufacturer identifies TIA/EIA-232-F compliance and IEC 61000-4-2 ESD test levels, but no RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for this exact ordering code.