Analog Devices

MAX3243EWI+T - 3.3V/5V 250kbps RS-232 Transceiver | Analog Devices

Référence : MAX3243EWI+T ✓ Actif
3 V to 5.5 V Vdss 1 µA Id 28-pin SOIC Package
MOQ : 1 |

MAX3243EWI+T Présentation

Analog Devices MAX3243EWI+T is a multichannel RS-232 line-driver and receiver interface IC with three transmit channels, five receive channels, a 3 V to 5.5 V supply range, and data rates up to 250 kbps. The device is offered in a 28-pin SOIC package and provides enhanced electrostatic-discharge protection rated at ±15 kV according to the Texas Instruments product page.

An RS-232 transceiver is an interface integrated circuit that converts logic-level UART signals into RS-232 line levels and converts received RS-232 signals back into CMOS-compatible logic levels. It belongs to the interface-IC hierarchy, where a physical-layer transceiver bridges a host controller or UART with a cable-based RS-232 communication port. The MAX3243's combination of multiple drivers, multiple receivers, and automatic power management makes it appropriate for multi-port industrial, instrumentation, and embedded systems.

Key features include three RS-232 drivers, five RS-232 receivers, operation from 3 V to 5.5 V, and throughput up to 250 kbps. AutoShutdown reduces supply current when the receiver inputs do not detect a valid signal level, with the product family described as reaching 1 µA supply current. This can be valuable in systems where an RS-232 port is connected infrequently because the interface can reduce loading while the link is inactive.

The MAX3243 family is designed for EIA/TIA-232 and V.28/V.24 communications interfaces. Three driver outputs support point-to-point serial links, while five receiver inputs provide additional monitoring channels. The family also includes an always-active receiver in the MAX3243 configuration, allowing a host to monitor another device even when the principal port is inactive. The E-qualified MAX3243 family adds enhanced ESD protection and automatic shutdown and wake-up behavior.

Typical uses include industrial control consoles, laboratory instruments, POS terminals, configuration ports, and service interfaces for embedded equipment. The 250 kbps capability provides a useful margin over common low-speed serial links, while the 28-pin SOIC package supports conventional surface-mount assembly. Designers should preserve the RS-232 voltage levels at the connector and route the interface according to the manufacturer's recommended application circuit.

Power-system design should account for transmit-state loading and supply-current changes as AutoShutdown detects valid receiver activity. Decoupling capacitors should be placed close to the supply and ground pins, and connector-side protection should complement the IC's internal ESD capability without excessive capacitance that could distort edges. Use the manufacturer pin-description table and recommended circuit when assigning tracks and selecting bypass components.

This product page combines the confirmed electrical and packaging characteristics with practical interface-selection guidance, drop-in replacement constraints, and PCB implementation notes. It is intended to help engineers identify whether the MAX3243EWI+T provides the required channel count, speed, supply range, package, and protection for an RS-232 design.

Alternatives de remplacement direct pour MAX3243EWI+T — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec MAX3243EWI+T (même facteur de forme et même empreinte) — différant par Package, Supply Voltage Range, ESD Protection, Maximum Data Rate, Communication Standard.

Analog Devices
Package: 28-pin TSSOP
Supply Voltage Range: 3.0 V to 5.5 V
ESD Protection: ±15 kV
Comparer avec MAX3243EWI+T →
Analog Devices
Package: 28-pin TSSOP
Supply Voltage Range: 3.0V to 5.5V
ESD Protection: ±15kV
Comparer avec MAX3243EWI+T →
Analog Devices
Package: 28-pin WSOIC
Supply Voltage Range: +3.0V to +5.5V
ESD Protection: ±15kV
Comparer avec MAX3243EWI+T →

MAX3243EEUI+T

✅ Remplacement direct
Analog Devices
📦 28-pin SOIC
RS-232 transceiver · 3.0V to 5.5V · 250kbps · 3 drivers · 5 receivers · Full duplex · ±15kV · 1µA

Contactez-nous pour le prix

Voir la fiche technique →

MAX3243ECUI+T

✅ Remplacement direct
Analog Devices
📦 28-pin SOIC
RS-232 transceiver · 3 · 5 · 3.0 V to 5.5 V · 250 kbps · ±15 kV · 1 µA · EIA/TIA-232

Contactez-nous pour le prix

Voir la fiche technique →

MAX3243CWI+T

✅ Remplacement direct
Analog Devices
📦 28-pin SOIC
3-driver, 5-receiver RS-232 transceiver · 3 V to 5.5 V · 250 kbps · 3 channels · 5 channels · 1 complementary receiver channel · ±15 kV · 1 µA

Contactez-nous pour le prix

Voir la fiche technique →

MAX3243CUI+T

✅ Remplacement direct
Analog Devices
📦 28-pin SOIC
3-driver, 5-receiver RS-232 transceiver · 3 V to 5.5 V · 250 kbps · 3 · 5 · Full duplex · ±15 kV · 1 µA

Contactez-nous pour le prix

Voir la fiche technique →

MAX3243EWI+G2X

✅ Remplacement direct
📦 28-pin SOIC
Same MAX3243E electrical function and 28-pin SOIC footprint; G2X identifies a different orderable packing or traceability configuration.

📋 Alternative de référence (hors catalogue)

MAX3243EWI+T Spécifications

Product Type RS-232 transceiver
Transmitter Channels 3 channels
Receiver Channels 5 channels
Tension d'alimentation de fonctionnement 3 V to 5.5 V
Maximum Data Rate 250 kbps
Enhanced ESD Protection ±15 kV
AutoShutdown Supply Current 1 µA
Duplex Type Full duplex
Communication Standard EIA/TIA-232 and V.28/V.24
Boîtier 28-pin SOIC
Type de montage Surface mount

Guide de configuration des broches du MAX3243EWI+T 28-pin soic

Configuration des broches du MAX3243EWI+T (boîtier 28-pin soic). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.

Schéma de brochage du boîtier 28-pin soic pour le MAX3243EWI+T

Aucune donnée de brochage détaillée disponible pour MAX3243EWI+T.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

MAX3243EWI+T convient pour 6 applications: Industrial Control Console, Laboratory Test Instrument, Point-of-Sale Terminal, Embedded Equipment Service Port, Medical Monitoring Equipment, Network Equipment Configuration Port.

🏭

Industrial Control Console

The MAX3243EWI+T fits an industrial console that must exchange commands and diagnostic data with a controller over a longer RS-232 link. Its 250 kbps maximum rate provides ample margin for common UART traffic, while the 3 V to 5.5 V supply range permits operation from either 3.3 V or 5 V control electronics. The five receiver channels are useful for monitoring multiple equipment-status or handshake signals in addition to the three available driver outputs. Automatic shutdown behavior can reduce supply consumption when no valid receiver activity is present, although the application must tolerate wake-up latency and cable transitions.

🔧

Laboratory Test Instrument

The MAX3243EWI+T is suitable for laboratory instruments that need several RS-232 status inputs alongside command outputs. A 250 kbps interface can support automated equipment communication without reaching the transceiver's upper rate limit, and operation from 3 V to 5.5 V allows the same family to be used across legacy 5 V instruments and newer 3.3 V control boards. The three drivers can support separate control, trigger, or service channels, while five receivers can monitor acknowledgements and interlocks. To maintain signal integrity, place bypass capacitance near the supply pins and use the manufacturer's recommended connector-side network.

🖥️

Point-of-Sale Terminal

The MAX3243EWI+T can support a point-of-sale terminal that combines data communication with peripheral status monitoring. Its three transmitter channels permit command, control, and optional auxiliary signaling paths, while the five receiver channels provide additional visibility into peripherals and acknowledgements. The 3 V to 5.5 V operating range accommodates both embedded processors and legacy peripheral interfaces. Automatic power management is useful in intermittently connected systems, but designers should verify that shutdown and wake-up timing does not delay an operator transaction or cause an attached peripheral to time out.

🧩

Embedded Equipment Service Port

The MAX3243EWI+T is appropriate for an embedded equipment service port that must remain accessible during maintenance while offering low standby loading. The MAX3243 family's AutoShutdown behavior can place the interface into a low-supply-current state when no valid receiver signal is detected, and the E-family documentation emphasizes automatic wake-up functionality. A rate of up to 250 kbps supports firmware download, configuration transfer, and diagnostic traffic on the same interface. System integrators should account for transient behavior at the connector and ensure that the external interface circuitry preserves the specified RS-232 signal levels.

💊

Medical Monitoring Equipment

The MAX3243EWI+T can be used in monitoring equipment that exposes a service or central-station interface while keeping multiple status signals under supervision. Its 3 V to 5.5 V supply compatibility supports integration with embedded controllers, and the five receiver channels are valuable when the system needs to observe ready, alarm, or interlock indications in addition to transmitting commands. The 250 kbps capability is well above the throughput normally required for configuration and status traffic. Medical-system designers must still evaluate the complete ordering grade, isolation architecture, applicable regulatory requirements, and connector protection for the installation environment.

🌐

Network Equipment Configuration Port

The MAX3243EWI+T is suitable for a management or configuration port in network equipment that also uses RS-232 for legacy subsystems. The three drivers can carry independent command or control signals, and five receivers allow the board to monitor several remote or local status lines. Operation up to 250 kbps provides margin for configuration transfers and logging, while the 3 V to 5.5 V range simplifies integration with mixed legacy logic. AutoShutdown may reduce idle consumption when the management connection is unused, but the design should validate wake-up behavior against the host timeout and should preserve adequate cable and connector protection.

What is the MAX3243EWI+T?
The MAX3243EWI+T is a 3-channel transmitter and 5-channel receiver RS-232 interface IC operating from 3 V to 5.5 V at up to 250 kbps. According to the Analog Devices MAX3243 product information, the device is packaged in a 28-pin SOIC and belongs to the MAX3243 family with automatic shutdown and wake-up features.
What is the operating voltage of MAX3243EWI+T?
The MAX3243EWI+T operates from 3 V to 5.5 V. The Texas Instruments MAX3243 product page identifies the device as a 3 V to 5.5 V multichannel RS-232 line driver and receiver. This range supports both common 3.3 V and 5 V system rails while retaining a single transceiver family for embedded and industrial equipment.
How many RS-232 drivers and receivers does MAX3243EWI+T have?
The MAX3243EWI+T provides three RS-232 transmit channels and five receive channels. Analog Devices describes the MAX3243 as a 3-driver, 5-receiver device with a complementary always-active receiver for external monitoring. The additional receivers allow more status or handshake signals to be observed than the three driver outputs alone would support.
What is the maximum data rate of MAX3243EWI+T?
The MAX3243EWI+T supports data rates up to 250 kbps. The Mouser product listing identifies it as a 3 V to 5.5 V, 250 kbps RS-232 transceiver, while the Texas Instruments product page confirms the 250 kbps rating. Actual application throughput can be lower when cable capacitance, loading, or protocol overhead increases.
What is the best drop-in replacement for MAX3243EWI+T?
The closest drop-in choices are MAX3243EEUI+T, MAX3243ECUI+T, MAX3243CWI+T, and MAX3243CUI+T, provided their temperature and protection requirements match the design. Each uses the same 28-pin SOIC family, but the E, C, and non-E variants differ in qualification and feature level. Verify the exact pin description and electrical limits before substitution.
What can replace MAX3243EWI+T?
A replacement must use the 28-pin SOIC footprint and preserve the required RS-232 channel arrangement. MAX3243EEUI+T, MAX3243ECUI+T, MAX3243CWI+T, and MAX3243CUI+T are same-family options identified through the MAX3243 cross-reference results. Their temperature grades, AutoShutdown behavior, and ESD ratings should be compared with the original system requirements.
Is MAX3243EWI+T the same as MAX3243EWI+?
The MAX3243EWI+ and MAX3243EWI+T denote the same MAX3243E device family, but the terminal ordering suffix can identify a different packing method. The +T designation commonly identifies tape-and-reel production packing, while the base orderable part can be supplied in another package format. Confirm reel configuration, quantity, and markings before treating the order codes as interchangeable.
MAX3243EWI+T vs MAX3243EEUI+T - which is better?
MAX3243EEUI+T is preferable when the installation requires the broader temperature grade represented by the EEUI ordering option. Both devices occupy the same 28-pin SOIC family and belong to the MAX3243E line, but the EEUI+T part is a distinct ordering variant with its own temperature limits. Compare the exact ordering table before selecting either device.
When should I choose MAX3243EWI+T over MAX3243CWI+T?
Choose MAX3243EWI+T when the interface requires the enhanced E-family behavior, including enhanced ESD protection and automatic shutdown and wake-up functions. MAX3243CWI+T is more appropriate when the basic MAX3243 functionality is sufficient and its specified operating limits satisfy the application. The distinction matters most for industrial temperature, ESD, and low-power requirements.
Is MAX3243EWI+T suitable for industrial equipment?
The MAX3243EWI+T is suitable for industrial interface designs when its specified operating-temperature and ESD ratings meet the equipment requirements. Analog Devices identifies the E family as enhanced-EIA/TIA-232 devices with automatic shutdown and wake-up, and Texas Instruments lists ±15 kV ESD protection. Final suitability depends on the complete ordering table and the enclosure and cable environment.
Where can I find the MAX3243EWI+T pinout and datasheet?
The MAX3243EWI+T pin description and application circuit are found in the Analog Devices MAX3243E manufacturer datasheet. The manufacturer product page is https://www.analog.com/en/products/max3243e.html, while the Texas Instruments product page is https://www.ti.com/product/MAX3243. Use the manufacturer pin table to assign all 28 SOIC connections and to confirm exposed-pad or no-connect details for the exact ordering code.
Where to buy MAX3243EWI+T and what is the lead time?
Use the Request a Quote form on this page to request current availability, lead time, minimum order quantity, and package quantity for MAX3243EWI+T. The form allows the exact MPN and tape-and-reel ordering suffix to be included in the inquiry. Stock and production timing can change, so they should be confirmed for the current order rather than inferred from a catalog entry.
What is the price of MAX3243EWI+T?
Use the Request a Quote form on this page for the current price of MAX3243EWI+T. The form is the appropriate channel for an exact 28-pin SOIC order with the +T tape-and-reel suffix. Quote requests should state the required quantity, reel format, shipment country, and target date so commercial and production details can be confirmed together.
Is MAX3243EWI+T in stock?
Current stock for MAX3243EWI+T should be requested through the Request a Quote form on this page. Enter the exact MPN, including the +T suffix, and specify the required production quantity. Because integrated-circuit inventory and lead time vary by order configuration, a confirmed allocation is more useful than a general catalog availability statement.
What are the key specifications of MAX3243EWI+T that engineers should know?
The principal MAX3243EWI+T specifications are a 3 V to 5.5 V supply, three transmit channels, five receive channels, operation up to 250 kbps, and a 28-pin SOIC package. Analog Devices and Texas Instruments product information also identify the MAX3243E family's automatic power management and ±15 kV ESD protection. These parameters should be checked together against cable length, UART rate, thermal conditions, and connector protection requirements.

Données de référence d'ingénierie pour MAX3243EWI+T — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose MAX3243EWI+T when the design needs three RS-232 transmit channels, five receive channels, operation from 3 V to 5.5 V, data rates up to 250 kbps, and enhanced E-family protection or automatic power management. The 28-pin SOIC package supports the same footprint as MAX3243EEUI+T, MAX3243ECUI+T, MAX3243CWI+T, and MAX3243CUI+T, but those ordering variants must be checked for temperature grade and feature differences. MAX3243CWI+T is appropriate when basic MAX3243 behavior is sufficient and enhanced protection is unnecessary. Use MAX3232ECDR when a two-driver, two-receiver arrangement better matches the design, and use MAX232EIDR for a simpler point-to-point port. For any replacement, verify the exact 28-pin pinout, supply limits, driver and receiver levels, ESD rating, temperature range, AutoShutdown timing, and cable-side circuit before production release.

Comparaison avec les alternatives

Paramètre Ce produit MAX3243EEUI+T MAX3243ECUI+T MAX3243CWI+T MAX3243CUI+T MAX3243EWI+G2X
Package 28-pin SOIC 28-pin SOIC 28-pin SOIC 28-pin SOIC 28-pin SOIC 28-pin SOIC
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Operating Supply Voltage 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V
Maximum Data Rate 250 kbps 250 kbps 250 kbps 250 kbps 250 kbps 250 kbps
Transmitter Channels 3 channels 3 channels 3 channels 3 channels 3 channels 3 channels
Receiver Channels 5 channels 5 channels 5 channels 5 channels 5 channels 5 channels

Principaux différenciateurs

  • Broader channel arrangement than a conventional dual RS-232 transceiver (vs MAX3232ECDR)
  • Enhanced-family protection and power management (vs MAX3243CWI+T)
  • Higher specified data rate than lower-speed comparison listings (vs MAX3243EWI+ listing with 120 kb/s specification)
  • Wide compatibility with common embedded supply rails (vs MAX3232ECDR)

Notes de conception

Follow the manufacturer application circuit for supply bypass and connector-side components. Place the decoupling capacitor immediately between the supply and ground pins, with a short return path and no unnecessary loop area. Keep sensitive receiver traces away from switching nodes and high-current return paths. Because the exact pin names and exposed-pad treatment are not reproduced on this page, assign PCB connections from the pin-description table for the exact MAX3243EWI+T ordering code.

RS-232 uses voltage-level signaling rather than differential impedance-controlled signaling, but cable capacitance and added protection components can still slow edges. Use the manufacturer's recommended network at each connector, avoid excessive stub lengths, and preserve the designed transmit and receive levels. Validate the slowest corner by measuring receiver transitions when long cables, adapters, or shared grounds are present.

Do not treat AutoShutdown behavior as an instantaneous power state. Verify the wake-up timing against the connected UART and host timeout, particularly during a cold connection or unplugged-cable event. Also distinguish the MAX3243E enhanced-protection family from non-E variants when substituting parts, and verify the exact temperature grade instead of relying only on the MAX3243 family name.

The transmitter load can change the device's power demand as outputs transition between logic and RS-232 levels. Use a supply with adequate transient margin for the complete three-channel design, and observe the maximum current and static current limits in the manufacturer datasheet. If several ports share a regulator, prevent local supply droop from disturbing unrelated digital rails by following recommended decoupling and isolation practices.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The verified product information identifies the MAX3243E family and its EIA/TIA-232 and V.28/V.24 interfaces but does not state component-specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 status.

Recherches associées

MAX3243EWI+T datasheet MAX3243EWI+T pinout MAX3243EWI+T datasheet pdf Analog Devices MAX3243EWI+T MAX3243EWI+T price MAX3243EWI+T stock MAX3243EWI+T equivalent MAX3243EWI+T replacement MAX3243EWI+T vs MAX3232ECDR MAX3243 28 pin SOIC RS-232 MAX3243 250 kbps transceiver MAX3243 3.3V RS-232 interface

Composants & termes associés

Analog Devices MAX3243EWI+T MAX3243 MAX3243E MAX3243EEUI+T MAX3243ECUI+T MAX3243CWI+T MAX3243CUI+T MAX3243EWI+G2X MAX3232ECDR MAX232EIDR RS-232 transceiver line driver line receiver interface IC physical-layer transceiver EIA/TIA-232 V.28 V.24 AutoShutdown ESD protection SOIC-28 surface-mount package UART industrial control laboratory instrumentation embedded service port
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ