MAX3243EWI+T - 3.3V/5V 250kbps RS-232 Transceiver | Analog Devices
MPN: MAX3243EWI+T ✓ فعالMAX3243EWI+T جائزہ
An RS-232 transceiver is an interface integrated circuit that converts logic-level UART signals into RS-232 line levels and converts received RS-232 signals back into CMOS-compatible logic levels. It belongs to the interface-IC hierarchy, where a physical-layer transceiver bridges a host controller or UART with a cable-based RS-232 communication port. The MAX3243's combination of multiple drivers, multiple receivers, and automatic power management makes it appropriate for multi-port industrial, instrumentation, and embedded systems.
Key features include three RS-232 drivers, five RS-232 receivers, operation from 3 V to 5.5 V, and throughput up to 250 kbps. AutoShutdown reduces supply current when the receiver inputs do not detect a valid signal level, with the product family described as reaching 1 µA supply current. This can be valuable in systems where an RS-232 port is connected infrequently because the interface can reduce loading while the link is inactive.
The MAX3243 family is designed for EIA/TIA-232 and V.28/V.24 communications interfaces. Three driver outputs support point-to-point serial links, while five receiver inputs provide additional monitoring channels. The family also includes an always-active receiver in the MAX3243 configuration, allowing a host to monitor another device even when the principal port is inactive. The E-qualified MAX3243 family adds enhanced ESD protection and automatic shutdown and wake-up behavior.
Typical uses include industrial control consoles, laboratory instruments, POS terminals, configuration ports, and service interfaces for embedded equipment. The 250 kbps capability provides a useful margin over common low-speed serial links, while the 28-pin SOIC package supports conventional surface-mount assembly. Designers should preserve the RS-232 voltage levels at the connector and route the interface according to the manufacturer's recommended application circuit.
Power-system design should account for transmit-state loading and supply-current changes as AutoShutdown detects valid receiver activity. Decoupling capacitors should be placed close to the supply and ground pins, and connector-side protection should complement the IC's internal ESD capability without excessive capacitance that could distort edges. Use the manufacturer pin-description table and recommended circuit when assigning tracks and selecting bypass components.
This product page combines the confirmed electrical and packaging characteristics with practical interface-selection guidance, drop-in replacement constraints, and PCB implementation notes. It is intended to help engineers identify whether the MAX3243EWI+T provides the required channel count, speed, supply range, package, and protection for an RS-232 design.
کے لیے ڈراپ اِن متبادل MAX3243EWI+T — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں MAX3243EWI+T (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Supply Voltage Range, ESD Protection, Maximum Data Rate, Communication Standard.
MAX3243EEUI+T
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MAX3243ECUI+T
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MAX3243CWI+T
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MAX3243CUI+T
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MAX3243EWI+G2X
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX3243EWI+T تفصیلات
| Product Type | RS-232 transceiver |
| Transmitter Channels | 3 channels |
| Receiver Channels | 5 channels |
| آپریٹنگ سپلائی وولٹیج | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Enhanced ESD Protection | ±15 kV |
| AutoShutdown Supply Current | 1 µA |
| Duplex Type | Full duplex |
| Communication Standard | EIA/TIA-232 and V.28/V.24 |
| پیکیج | 28-pin SOIC |
| ماؤنٹنگ ٹائپ | Surface mount |
MAX3243EWI+T 28-pin soic پن کنفیگریشن گائیڈ
MAX3243EWI+T (28-pin soic پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں MAX3243EWI+T.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
MAX3243EWI+T کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Control Console, Laboratory Test Instrument, Point-of-Sale Terminal, Embedded Equipment Service Port, Medical Monitoring Equipment, Network Equipment Configuration Port.
Industrial Control Console
The MAX3243EWI+T fits an industrial console that must exchange commands and diagnostic data with a controller over a longer RS-232 link. Its 250 kbps maximum rate provides ample margin for common UART traffic, while the 3 V to 5.5 V supply range permits operation from either 3.3 V or 5 V control electronics. The five receiver channels are useful for monitoring multiple equipment-status or handshake signals in addition to the three available driver outputs. Automatic shutdown behavior can reduce supply consumption when no valid receiver activity is present, although the application must tolerate wake-up latency and cable transitions.
تجویز کردہ
Laboratory Test Instrument
The MAX3243EWI+T is suitable for laboratory instruments that need several RS-232 status inputs alongside command outputs. A 250 kbps interface can support automated equipment communication without reaching the transceiver's upper rate limit, and operation from 3 V to 5.5 V allows the same family to be used across legacy 5 V instruments and newer 3.3 V control boards. The three drivers can support separate control, trigger, or service channels, while five receivers can monitor acknowledgements and interlocks. To maintain signal integrity, place bypass capacitance near the supply pins and use the manufacturer's recommended connector-side network.
تجویز کردہ
Point-of-Sale Terminal
The MAX3243EWI+T can support a point-of-sale terminal that combines data communication with peripheral status monitoring. Its three transmitter channels permit command, control, and optional auxiliary signaling paths, while the five receiver channels provide additional visibility into peripherals and acknowledgements. The 3 V to 5.5 V operating range accommodates both embedded processors and legacy peripheral interfaces. Automatic power management is useful in intermittently connected systems, but designers should verify that shutdown and wake-up timing does not delay an operator transaction or cause an attached peripheral to time out.
تجویز کردہ
Embedded Equipment Service Port
The MAX3243EWI+T is appropriate for an embedded equipment service port that must remain accessible during maintenance while offering low standby loading. The MAX3243 family's AutoShutdown behavior can place the interface into a low-supply-current state when no valid receiver signal is detected, and the E-family documentation emphasizes automatic wake-up functionality. A rate of up to 250 kbps supports firmware download, configuration transfer, and diagnostic traffic on the same interface. System integrators should account for transient behavior at the connector and ensure that the external interface circuitry preserves the specified RS-232 signal levels.
تجویز کردہ
Medical Monitoring Equipment
The MAX3243EWI+T can be used in monitoring equipment that exposes a service or central-station interface while keeping multiple status signals under supervision. Its 3 V to 5.5 V supply compatibility supports integration with embedded controllers, and the five receiver channels are valuable when the system needs to observe ready, alarm, or interlock indications in addition to transmitting commands. The 250 kbps capability is well above the throughput normally required for configuration and status traffic. Medical-system designers must still evaluate the complete ordering grade, isolation architecture, applicable regulatory requirements, and connector protection for the installation environment.
تجویز کردہ
Network Equipment Configuration Port
The MAX3243EWI+T is suitable for a management or configuration port in network equipment that also uses RS-232 for legacy subsystems. The three drivers can carry independent command or control signals, and five receivers allow the board to monitor several remote or local status lines. Operation up to 250 kbps provides margin for configuration transfers and logging, while the 3 V to 5.5 V range simplifies integration with mixed legacy logic. AutoShutdown may reduce idle consumption when the management connection is unused, but the design should validate wake-up behavior against the host timeout and should preserve adequate cable and connector protection.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا MAX3243EWI+T — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | MAX3243EEUI+T | MAX3243ECUI+T | MAX3243CWI+T | MAX3243CUI+T | MAX3243EWI+G2X |
|---|---|---|---|---|---|---|
| Package | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Operating Supply Voltage | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps | 250 kbps | 250 kbps | 250 kbps |
| Transmitter Channels | 3 channels | 3 channels | 3 channels | 3 channels | 3 channels | 3 channels |
| Receiver Channels | 5 channels | 5 channels | 5 channels | 5 channels | 5 channels | 5 channels |
اہم امتیازی خصوصیات
- Broader channel arrangement than a conventional dual RS-232 transceiver (بمقابلہMAX3232ECDR)
- Enhanced-family protection and power management (بمقابلہMAX3243CWI+T)
- Higher specified data rate than lower-speed comparison listings (بمقابلہMAX3243EWI+ listing with 120 kb/s specification)
- Wide compatibility with common embedded supply rails (بمقابلہMAX3232ECDR)
ڈیزائن نوٹس
Follow the manufacturer application circuit for supply bypass and connector-side components. Place the decoupling capacitor immediately between the supply and ground pins, with a short return path and no unnecessary loop area. Keep sensitive receiver traces away from switching nodes and high-current return paths. Because the exact pin names and exposed-pad treatment are not reproduced on this page, assign PCB connections from the pin-description table for the exact MAX3243EWI+T ordering code.
RS-232 uses voltage-level signaling rather than differential impedance-controlled signaling, but cable capacitance and added protection components can still slow edges. Use the manufacturer's recommended network at each connector, avoid excessive stub lengths, and preserve the designed transmit and receive levels. Validate the slowest corner by measuring receiver transitions when long cables, adapters, or shared grounds are present.
Do not treat AutoShutdown behavior as an instantaneous power state. Verify the wake-up timing against the connected UART and host timeout, particularly during a cold connection or unplugged-cable event. Also distinguish the MAX3243E enhanced-protection family from non-E variants when substituting parts, and verify the exact temperature grade instead of relying only on the MAX3243 family name.
The transmitter load can change the device's power demand as outputs transition between logic and RS-232 levels. Use a supply with adequate transient margin for the complete three-channel design, and observe the maximum current and static current limits in the manufacturer datasheet. If several ports share a regulator, prevent local supply droop from disturbing unrelated digital rails by following recommended decoupling and isolation practices.
تعمیل کی معلومات
The verified product information identifies the MAX3243E family and its EIA/TIA-232 and V.28/V.24 interfaces but does not state component-specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 status.