MAX325EPA+ - Dual Precision SPST Switch | Maxim Integrated
Référence : MAX325EPA+ ✓ ActifMAX325EPA+ Présentation
An analog switch is an integrated semiconductor device that routes electrical signals between circuit nodes under digital control. The MAX325EPA+ belongs to the analog switch hierarchy, which includes multiplexers, selectors, and switch matrices. Its SPST configuration provides one independent normally open connection for each of two channels, making it useful when a system must isolate, route, or protect analog signals without changing the signal level significantly.
Key characteristics include two independent SPST channels, single-supply operation from 2.7 V to 16 V, a 60 ohm listed on-resistance, approximately 5 microwatt power consumption, and TTL compatibility when operated from a single 5 V supply. The device is packaged in an 8-pin PDIP measuring 0.300 inch, or 7.62 mm, across the package body. These characteristics suit compact, low-power signal-routing designs where an analog switch must operate from a limited supply rail.
The MAX325EPA+ separates analog signal paths from control logic while preserving a straightforward interface. Each switch provides a 1:1 connection when enabled and disconnects the corresponding path when disabled. Single-supply operation simplifies the power architecture in battery-powered instrumentation, but the selected supply voltage and control levels must remain compatible with the switch threshold requirements. In a 5 V system, the device is described as TTL compatible.
Typical applications include battery-powered measurement systems, automated test equipment, sensor signal routing, analog input selection, sample-and-hold circuitry, and communication equipment requiring two controllable analog paths. The approximately 5 microwatt power consumption is especially useful in portable equipment where every leakage and static current contributes to battery drain.
PCB design should keep each switched trace short and connect the device ground pins to a low-impedance ground plane. Because the MAX325EPA+ uses through-hole PDIP construction, it is most appropriate for leaded assemblies, prototypes, industrial controllers, and test fixtures rather than compact surface-mount production boards.
This product page combines distributor availability information, package identification, electrical characteristics, application guidance, and verified replacement information to support faster component selection and board-level planning.
Alternatives de remplacement direct pour MAX325EPA+ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
MAX325CPA+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX325EPA+ Valeurs maximales et caractéristiques électriques
| Number of Circuits | 2 circuits |
| Switch Configuration | 1:1 |
| Channel Configuration | 2 x SPST |
| Listed On-Resistance | 60 ohm |
| Supply Voltage Range | 2.7 V to 16 V |
| Typical Power Consumption | 5 microwatts |
| TTL Compatibility | Compatible with a single 5 V supply |
| Temperature Grade | Industrial |
| Number of Terminals | 8 terminals |
| Package Type | 8-pin PDIP |
| Package Body Width | 0.300 inch (7.62 mm) |
| Style de montage | Through hole |
| Surface Mount | No |
| Product Type | Precision, single-supply, SPST analog switch |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
Guide de configuration des broches du MAX325EPA+ 0.300 inch (7.62 mm)
Configuration des broches du MAX325EPA+ (boîtier 0.300 inch (7.62 mm)). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour MAX325EPA+.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MAX325EPA+ convient pour 6 applications: Battery-Powered Sensor Signal Routing, Automated Test Equipment Signal Selection, Analog Input Multiplexing, Sample-and-Hold Signal Isolation, Industrial Control Signal Isolation, Communication Equipment Signal Gating.
Battery-Powered Sensor Signal Routing
The MAX325EPA+ fits portable sensor acquisition because it combines two independently controlled SPST paths with approximately 5 microwatt power consumption and a 2.7 V minimum supply. Place one channel on the sensor output and use the other for a reference, calibration, or isolation path. This arrangement lets a controller disconnect an inactive sensor without continuously loading its output. Because the device is a 1:1 switch, the selected signal is passed with limited resistance rather than converted or actively buffered. Confirm that the sensor output voltage remains within the switch's input range and that control thresholds are compatible with the host microcontroller.
Recommandé
Automated Test Equipment Signal Selection
The MAX325EPA+ is useful in automated test equipment where two SPST paths can be selected or isolated under fixture-control logic. Its 2-channel architecture allows one DUT-related path and one instrument-reference path to share a controlled interface. The 8-pin PDIP format supports rugged through-hole assembly and easy replacement in legacy or industrial fixtures. For low-amplitude measurements, engineers should verify on-resistance, leakage, off-isolation, and bandwidth under the manufacturer's stated test conditions rather than relying on a single distributor resistance figure.
Recommandé
Analog Input Multiplexing
The MAX325EPA+ can be used in small analog-input selection networks where a controller must connect one of two sources to a downstream measurement channel. Its SPST behavior provides a clean disconnect between the active source and the common node, while the 2.7 V to 16 V supply range permits use in both compact low-voltage systems and higher-voltage instrumentation. With two channels, the device can route either the selected input or a reference signal. Validate source impedance, settling behavior, injected error, and switch capacitance before using it for precision ADC front ends.
Recommandé
Sample-and-Hold Signal Isolation
The MAX325EPA+ can isolate a sampling node during acquisition and connect it to a measurement amplifier at the appropriate time. Two independent SPST switches can control separate portions of the signal path, allowing the design to reduce unwanted interaction between the source and the hold capacitor. The approximately 5 microwatt power consumption is valuable in portable test equipment, where the switch should not dominate standby demand. The circuit must account for switch on-resistance, charge injection, off-isolation, and the leakage of the external hold capacitor; consult the Maxim Integrated datasheet for test conditions and timing details.
Recommandé
Industrial Control Signal Isolation
The MAX325EPA+ can isolate or redirect control signals in industrial control systems through its two independent SPST channels. The 1:1 configuration preserves signal polarity and voltage, and TTL compatibility from a 5 V supply simplifies control from conventional digital logic. Its through-hole PDIP-8 package is practical for controller boards where long-term mechanical robustness and serviceability matter more than board area. Designers should confirm the industrial temperature range, absolute maximum ratings, and behavior during power-up or control-sequence transitions before integrating the switch into safety-related or high-energy circuits.
Recommandé
Communication Equipment Signal Gating
The MAX325EPA+ can gate or isolate two low-frequency communication paths when a system requires controlled connection between source and destination circuitry. The single 5 V TTL-compatible operating mode supports integration with legacy digital control logic, while the dual SPST arrangement allows independent management of a forward path and a monitoring path. Because the device is a passive 1:1 switch rather than an active transceiver, the system must handle level translation and impedance matching separately. Verify bandwidth, insertion loss, off-isolation, and logic thresholds in the target signal environment.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MAX325EPA+ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MAX325CPA+ |
|---|---|---|
| Package | PDIP-8 | PDIP-8 - same package |
| Brand | Maxim Integrated | Maxim Integrated |
| Number of Circuits | 2 circuits | 2 channels |
| Switch Configuration | 2 x SPST, 1:1 | 2 x SPST |
| Mounting Style | Through hole | Through hole |
Principaux différenciateurs
- Two independent analog paths in one package (vs MAX325CPA+)
- Single-supply operation for compact systems (vs MAX325CPA+)
- Direct 5 V digital-interface compatibility (vs MAX325CPA+)
Notes de conception
Route each switched analog path as a short, continuous trace and connect the device ground pins directly to a low-impedance ground plane. Keep digital control traces away from sensitive analog nets to reduce capacitive coupling from control-edge transitions. For the PDIP-8 implementation, preserve adequate spacing between opposite-row pins and between the IC and nearby tall components so the device can be inserted and soldered without mechanical interference.
Validate the complete switched path rather than relying only on the nominal on-resistance. Account for the resistance of source and destination impedances, switch leakage, off-isolation, bandwidth, and the external capacitance of wiring or fixtures. The available records report both 60 ohm and 175 ohm for closely identified variants, so use the Maxim Integrated datasheet's exact test conditions before calculating insertion loss or ADC settling behavior.
Design the enable sequence so the control input cannot float while the analog path carries current. Confirm the valid logic thresholds for the selected supply voltage and provide a defined state during power-up and shutdown. Although the MAX325EPA+ consumes approximately 5 microwatts, leakage through an externally powered switch can dominate standby current in a battery-powered design, so include it in the complete power-budget calculation.
Do not assume that package similarity alone proves that a substitute is electrically interchangeable. For MAX325CPA+, compare pin names, on-resistance test conditions, control thresholds, leakage, off-isolation, bandwidth, and absolute maximum ratings against the MAX325EPA+ datasheet. Also check that the chosen ordering code matches the required PDIP-8 form factor and operating-temperature grade before releasing a production BOM.
Informations de conformité
The device is identified as industrial grade, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement is present in the available product records.