Maxim Integrated

MAX325EPA+ - Dual Precision SPST Switch | Maxim Integrated

부품 번호: MAX325EPA+ ✓ 활성
2.7 V to 16 V Vdss 60 ohm Rds(on) 8-pin PDIP Package
MOQ: 1 |

MAX325EPA+ 개요

Maxim Integrated MAX325EPA+ is a precision, single-supply, dual SPST analog switch with two independently controlled circuits, 1:1 signal routing, and an 8-pin PDIP package. The device operates from 2.7 V to 16 V, has a listed on-resistance of 60 ohm at DigiKey, and is specified as a low-power component consuming approximately 5 microwatts.

An analog switch is an integrated semiconductor device that routes electrical signals between circuit nodes under digital control. The MAX325EPA+ belongs to the analog switch hierarchy, which includes multiplexers, selectors, and switch matrices. Its SPST configuration provides one independent normally open connection for each of two channels, making it useful when a system must isolate, route, or protect analog signals without changing the signal level significantly.

Key characteristics include two independent SPST channels, single-supply operation from 2.7 V to 16 V, a 60 ohm listed on-resistance, approximately 5 microwatt power consumption, and TTL compatibility when operated from a single 5 V supply. The device is packaged in an 8-pin PDIP measuring 0.300 inch, or 7.62 mm, across the package body. These characteristics suit compact, low-power signal-routing designs where an analog switch must operate from a limited supply rail.

The MAX325EPA+ separates analog signal paths from control logic while preserving a straightforward interface. Each switch provides a 1:1 connection when enabled and disconnects the corresponding path when disabled. Single-supply operation simplifies the power architecture in battery-powered instrumentation, but the selected supply voltage and control levels must remain compatible with the switch threshold requirements. In a 5 V system, the device is described as TTL compatible.

Typical applications include battery-powered measurement systems, automated test equipment, sensor signal routing, analog input selection, sample-and-hold circuitry, and communication equipment requiring two controllable analog paths. The approximately 5 microwatt power consumption is especially useful in portable equipment where every leakage and static current contributes to battery drain.

PCB design should keep each switched trace short and connect the device ground pins to a low-impedance ground plane. Because the MAX325EPA+ uses through-hole PDIP construction, it is most appropriate for leaded assemblies, prototypes, industrial controllers, and test fixtures rather than compact surface-mount production boards.

This product page combines distributor availability information, package identification, electrical characteristics, application guidance, and verified replacement information to support faster component selection and board-level planning.

드롭인 대체품: MAX325EPA+ — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

MAX325CPA+

✅ 드롭인
📦 PDIP-8
Same 2-channel, 2 x SPST configuration and 8-pin PDIP package; the available records do not quantify the on-resistance or control-threshold difference

📋 참조 대체품 (카탈로그에 없음)

MAX325EPA+ 최대 정격 & 전기적 특성

Number of Circuits 2 circuits
Switch Configuration 1:1
Channel Configuration 2 x SPST
Listed On-Resistance 60 ohm
Supply Voltage Range 2.7 V to 16 V
Typical Power Consumption 5 microwatts
TTL Compatibility Compatible with a single 5 V supply
Temperature Grade Industrial
Number of Terminals 8 terminals
Package Type 8-pin PDIP
Package Body Width 0.300 inch (7.62 mm)
장착 스타일 Through hole
Surface Mount No
Product Type Precision, single-supply, SPST analog switch
RoHS Compliance unknown
REACH Compliance unknown

MAX325EPA+ 0.300 inch (7.62 mm) 핀 구성 가이드

MAX325EPA+(0.300 inch (7.62 mm) 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.

MAX325EPA+의 0.300 inch (7.62 mm) 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: MAX325EPA+.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

MAX325EPA+ 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Signal Routing, Automated Test Equipment Signal Selection, Analog Input Multiplexing, Sample-and-Hold Signal Isolation, Industrial Control Signal Isolation, Communication Equipment Signal Gating.

🔋

Battery-Powered Sensor Signal Routing

The MAX325EPA+ fits portable sensor acquisition because it combines two independently controlled SPST paths with approximately 5 microwatt power consumption and a 2.7 V minimum supply. Place one channel on the sensor output and use the other for a reference, calibration, or isolation path. This arrangement lets a controller disconnect an inactive sensor without continuously loading its output. Because the device is a 1:1 switch, the selected signal is passed with limited resistance rather than converted or actively buffered. Confirm that the sensor output voltage remains within the switch's input range and that control thresholds are compatible with the host microcontroller.

🖥️

Automated Test Equipment Signal Selection

The MAX325EPA+ is useful in automated test equipment where two SPST paths can be selected or isolated under fixture-control logic. Its 2-channel architecture allows one DUT-related path and one instrument-reference path to share a controlled interface. The 8-pin PDIP format supports rugged through-hole assembly and easy replacement in legacy or industrial fixtures. For low-amplitude measurements, engineers should verify on-resistance, leakage, off-isolation, and bandwidth under the manufacturer's stated test conditions rather than relying on a single distributor resistance figure.

🔧

Analog Input Multiplexing

The MAX325EPA+ can be used in small analog-input selection networks where a controller must connect one of two sources to a downstream measurement channel. Its SPST behavior provides a clean disconnect between the active source and the common node, while the 2.7 V to 16 V supply range permits use in both compact low-voltage systems and higher-voltage instrumentation. With two channels, the device can route either the selected input or a reference signal. Validate source impedance, settling behavior, injected error, and switch capacitance before using it for precision ADC front ends.

📈

Sample-and-Hold Signal Isolation

The MAX325EPA+ can isolate a sampling node during acquisition and connect it to a measurement amplifier at the appropriate time. Two independent SPST switches can control separate portions of the signal path, allowing the design to reduce unwanted interaction between the source and the hold capacitor. The approximately 5 microwatt power consumption is valuable in portable test equipment, where the switch should not dominate standby demand. The circuit must account for switch on-resistance, charge injection, off-isolation, and the leakage of the external hold capacitor; consult the Maxim Integrated datasheet for test conditions and timing details.

🏭

Industrial Control Signal Isolation

The MAX325EPA+ can isolate or redirect control signals in industrial control systems through its two independent SPST channels. The 1:1 configuration preserves signal polarity and voltage, and TTL compatibility from a 5 V supply simplifies control from conventional digital logic. Its through-hole PDIP-8 package is practical for controller boards where long-term mechanical robustness and serviceability matter more than board area. Designers should confirm the industrial temperature range, absolute maximum ratings, and behavior during power-up or control-sequence transitions before integrating the switch into safety-related or high-energy circuits.

🌐

Communication Equipment Signal Gating

The MAX325EPA+ can gate or isolate two low-frequency communication paths when a system requires controlled connection between source and destination circuitry. The single 5 V TTL-compatible operating mode supports integration with legacy digital control logic, while the dual SPST arrangement allows independent management of a forward path and a monitoring path. Because the device is a passive 1:1 switch rather than an active transceiver, the system must handle level translation and impedance matching separately. Verify bandwidth, insertion loss, off-isolation, and logic thresholds in the target signal environment.

추천 제품 요약

MAX325EPA+ Maxim Integrated 사용처: Battery-Powered Sensor Signal Routing, Automated Test Equipment Signal Selection, Analog Input Multiplexing, Sample-and-Hold Signal Isolation, Industrial Control Signal Isolation, Communication Equipment Signal Gating MAX325CPA+ PDIP-8 comparator in the same switch family 사용처: Battery-Powered Sensor Signal Routing, Analog Input Multiplexing, Industrial Control Signal Isolation MAX323CPA+ Maxim single-supply switch comparator 사용처: Automated Test Equipment Signal Selection, Sample-and-Hold Signal Isolation, Communication Equipment Signal Gating
What is the MAX325EPA+?
The MAX325EPA+ is a Maxim Integrated precision, single-supply analog switch containing two independent SPST circuits. According to the Maxim Integrated datasheet, it uses a 1:1 signal configuration, operates from 2.7 V to 16 V, and is packaged in an 8-pin PDIP. The device is intended for controlled routing of analog signals in low-power instrumentation and test systems.
What are the key specifications of MAX325EPA+ that engineers should know?
The MAX325EPA+ provides two independent SPST channels, a 1:1 routing configuration, a 2.7 V to 16 V supply range, and a listed 60 ohm on-resistance at DigiKey. The Maxim Integrated datasheet also describes approximately 5 microwatt power consumption and TTL compatibility from a single 5 V supply. Its 8-pin PDIP package is suitable for through-hole assembly.
What is the operating voltage of MAX325EPA+?
The MAX325EPA+ operates from 2.7 V to 16 V. The Maxim Integrated datasheet identifies the component as a single-supply precision SPST analog switch, while DigiKey lists it as a two-circuit 1:1 switch. Design the control signals and switched-node voltages so they remain within the device's specified input and output limits.
How many channels and switches does MAX325EPA+ contain?
The MAX325EPA+ contains two channels, each configured as one SPST switch. The Maxim Integrated datasheet and the Xecor comparison identify the configuration as 2 x SPST, while DigiKey describes the part as a two-circuit IC switch with 1:1 operation. Each channel can therefore connect one signal path when its control input is asserted.
What is the on-resistance of MAX325EPA+?
DigiKey lists the MAX325EPA+ with an on-resistance of 60 ohm. Another distributor datasheet excerpt reports 175 ohm for the MAX325EPA, so engineers should confirm the test conditions and ensure both figures refer to the same production variant before using either number in a loss calculation. The Maxim Integrated datasheet should be treated as the controlling technical document.
Where can I download the MAX325EPA+ datasheet PDF?
The MAX325EPA+ datasheet is available through the Maxim Integrated datasheet link identified in the product records and through the datasheet download page listed for the MAX325EPA. The document describes the precision, single-supply, two-channel SPST configuration and identifies the 8-pin PDIP package. Use the manufacturer document when finalizing electrical limits, logic thresholds, and test conditions.
Where can I find the MAX325EPA+ pinout?
The MAX325EPA+ uses an 8-pin PDIP package, and its pin assignment should be taken from the pin-description table in the Maxim Integrated datasheet. The available product records identify the package and pin count but do not reproduce the complete pin names. Use the manufacturer pin-description table when assigning control inputs, switched terminals, and supply connections on the PCB.
Is MAX325EPA+ suitable for battery-powered equipment?
Yes, the MAX325EPA+ is suitable for battery-powered equipment because it is a single-supply device operating from 2.7 V to 16 V and consumes approximately 5 microwatts according to the Maxim Integrated datasheet. The design should still include a controlled shutdown strategy or unpowered-state analysis when leakage through the switched terminals could materially affect standby battery life.
MAX325EPA+ vs MAX325CPA+ - which is better for a through-hole design?
The MAX325EPA+ and MAX325CPA+ are the better comparison for a through-hole design because both are identified as 2-channel, 2 x SPST devices in PDIP-8 packages. The available comparison records show the same package and switching topology, but they do not quantify every electrical parameter. Compare the Maxim Integrated datasheets for exact on-resistance, control thresholds, and temperature limits before treating either part as interchangeable.
What is the best drop-in replacement for MAX325EPA+?
The MAX325CPA+ is the closest supported drop-in candidate identified for the MAX325EPA+ because both use an 8-pin PDIP package with two independent SPST channels. The available records do not provide a complete pin-by-pin and electrical comparison, so qualification should include the Maxim Integrated datasheets, continuity testing, logic-level verification, and a check of the operating-temperature limits before production use.
Can MAX325CPA+ replace MAX325EPA+?
MAX325CPA+ can be considered a possible drop-in replacement for MAX325EPA+ because comparison records identify both as Maxim Integrated two-channel SPST analog switches in PDIP-8 packages. Its package match is confirmed, while a complete quantified electrical match is not established in the available records. Verify pin assignment, control thresholds, on-resistance conditions, and operating-temperature coverage before substitution.
When should I choose MAX325EPA+ instead of MAX325CPA+?
Choose the MAX325EPA+ when its Maxim Integrated datasheet provides the required electrical limits and temperature coverage for the intended application and when the exact MAX325EPA+ ordering configuration is preferable. MAX325CPA+ remains the relevant same-package comparator, but the available records do not establish a complete parameter-by-parameter advantage. Make the final choice from controlled datasheet conditions rather than package similarity alone.
Where can I buy MAX325EPA+ and what is its price?
The MAX325EPA+ can be requested through the Request a Quote form on this page for current commercial terms, availability, and lead time. Current pricing is not embedded in this technical description because it can change by quantity, date, and supply status. Submit the required quantity, package, and target date with the request for a current quotation.
What is the lead time for MAX325EPA+?
Current lead time for MAX325EPA+ should be confirmed through the Request a Quote form on this page. One product record reported immediate shipment, but that observation is not a guaranteed lead time for a new quotation. Provide the required quantity, date code requirements, and target delivery date so the current supply position can be evaluated.
Is MAX325EPA+ in stock?
Stock availability for MAX325EPA+ changes with quantity and supplier inventory, so the current position should be confirmed through the Request a Quote form on this page. A product record reported 4,992 pieces in stock, but that observation may not reflect subsequent transactions or the requested quantity. Submit the required quantity for a current availability response.
What are the main design considerations for a MAX325EPA+ PCB layout?
The primary MAX325EPA+ layout consideration is to preserve the integrity of the switched analog path and provide a low-impedance ground connection. Keep switched traces short, route control inputs away from sensitive analog nodes, and connect supply and ground pins to planes or robust traces. The 8-pin PDIP format also requires adequate lead clearance for through-hole soldering and connector accessibility.

엔지니어링 참조 데이터: MAX325EPA+ — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the MAX325EPA+ when the design needs two independent SPST paths, single-supply operation from 2.7 V to 16 V, low power consumption, and a through-hole PDIP-8 footprint. It is particularly suitable for portable instrumentation, automated test fixtures, sensor routing, and low-frequency communication paths where controlled isolation is required without active level conversion. MAX325CPA+ is the closest supported same-package alternative because the comparison records show the same two-channel SPST topology and PDIP-8 construction. Select it only after confirming the manufacturer datasheets establish compatible pin assignment, logic thresholds, on-resistance conditions, leakage, off-isolation, bandwidth, and temperature coverage. Neither candidate should be chosen solely because the package is identical. If board area is the overriding priority, a surface-mount switch may be more appropriate, but that is a footprint redesign rather than a drop-in substitution.

대체품과의 비교

파라미터 이 제품 MAX325CPA+
Package PDIP-8 PDIP-8 - same package
Brand Maxim Integrated Maxim Integrated
Number of Circuits 2 circuits 2 channels
Switch Configuration 2 x SPST, 1:1 2 x SPST
Mounting Style Through hole Through hole

주요 차별점

  • Two independent analog paths in one package (vs MAX325CPA+)
  • Single-supply operation for compact systems (vs MAX325CPA+)
  • Direct 5 V digital-interface compatibility (vs MAX325CPA+)

설계 노트

Route each switched analog path as a short, continuous trace and connect the device ground pins directly to a low-impedance ground plane. Keep digital control traces away from sensitive analog nets to reduce capacitive coupling from control-edge transitions. For the PDIP-8 implementation, preserve adequate spacing between opposite-row pins and between the IC and nearby tall components so the device can be inserted and soldered without mechanical interference.

Validate the complete switched path rather than relying only on the nominal on-resistance. Account for the resistance of source and destination impedances, switch leakage, off-isolation, bandwidth, and the external capacitance of wiring or fixtures. The available records report both 60 ohm and 175 ohm for closely identified variants, so use the Maxim Integrated datasheet's exact test conditions before calculating insertion loss or ADC settling behavior.

Design the enable sequence so the control input cannot float while the analog path carries current. Confirm the valid logic thresholds for the selected supply voltage and provide a defined state during power-up and shutdown. Although the MAX325EPA+ consumes approximately 5 microwatts, leakage through an externally powered switch can dominate standby current in a battery-powered design, so include it in the complete power-budget calculation.

Do not assume that package similarity alone proves that a substitute is electrically interchangeable. For MAX325CPA+, compare pin names, on-resistance test conditions, control thresholds, leakage, off-isolation, bandwidth, and absolute maximum ratings against the MAX325EPA+ datasheet. Also check that the chosen ordering code matches the required PDIP-8 form factor and operating-temperature grade before releasing a production BOM.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The device is identified as industrial grade, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement is present in the available product records.

데이터 검증일: 2026-11-09 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

MAX325EPA+ datasheet MAX325EPA+ pinout MAX325EPA+ datasheet pdf MAX325EPA+ specifications MAX325EPA+ equivalent MAX325EPA+ replacement MAX325EPA+ vs MAX325CPA+ MAX325EPA+ PDIP-8 Maxim Integrated MAX325EPA+ MAX325EPA+ price MAX325EPA+ stock MAX325EPA+ analog switch MAX325EPA+ application circuit MAX325EPA+ cross reference

관련 부품 & 용어

Maxim Integrated MAX325EPA+ MAX325CPA+ MAX323CPA+ MAX325EPA precision analog switch SPST analog switch 2 x SPST 1:1 switch single-supply operation interface IC semiconductor PDIP-8 DIP package family through-hole component on-resistance off-isolation TTL-compatible control battery-powered instrumentation automated test equipment sensor signal routing industrial control RoHS REACH
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기