MAX3485ESA/GG8 - 3.3V 10Mbps RS-485 Transceiver | Analog Devices
Référence : MAX3485ESA/GG8 ✓ ActifMAX3485ESA/GG8 Présentation
An RS-485 transceiver is an interface IC that converts logic-level signals into differential differential-pair voltages for reliable communication over noisy or long cables. It also converts received differential signals back into CMOS-compatible logic. The MAX3485 family occupies the interface IC layer within communication systems and combines a line driver, line receiver, and bus-management functions in one package. Its 3.3 V supply supports compact industrial, instrumentation, and embedded-control designs operating from modern low-voltage logic rails.
Key operating characteristics include 3.3 V power, a maximum data rate of 10 Mbps, one driver and one receiver, and an 8-pin SOIC footprint. The MAX3485ESA/GG8 is identified as the manufacturer’s extended-temperature part ordering code. The product family description also identifies low-power operation and thermal protection. These characteristics make the device useful where space, bus speed, reduced edge-rate emissions, and dependable differential signaling are more important than integrating multiple protocol-specific interface functions.
The integrated driver and receiver support half-duplex RS-485 networks in which a node transmits and receives on the same pair. RS-422 systems can also use the driver and receiver, although the two protocols have different network topologies and driver-enable expectations. The differential signal method improves noise immunity because the receiver evaluates the voltage difference between the two conductors rather than relying on a single conductor referenced only to ground. That principle is especially valuable around motors, relays, switching supplies, and long cables.
Typical uses include multi-drop industrial measurement buses, factory-floor controllers, building automation nodes, instrument interfaces, and embedded serial links between a controller and a remote sensor or actuator. A bus may accommodate as many as 256 devices when the complete system is designed for that population, including appropriate termination, biasing, cable length, topology, and data-rate limits. Device count alone does not guarantee successful communication because the complete bus topology must satisfy the selected transceiver’s electrical requirements.
The principal design consideration is the relationship between data rate, cable length, topology, termination, and driver edge rate. Keep the differential route compact, use a continuous ground reference where system architecture permits, place termination only at the physical ends of the bus, and verify the driver-enable timing in half-duplex designs. This page consolidates the device’s operating characteristics, package information, application guidance, pinout-status disclosure, and a verified functional-equivalent candidate to support faster engineering review.
Alternatives de remplacement direct pour MAX3485ESA/GG8 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MAX3485ESA/GG8 (même facteur de forme et même empreinte) — différant par Product Type, Mounting Type, Package, Supported Standards.
SP3485CN-L
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MAX3485ESA/GG8 Spécifications
| Product Type | RS-485/RS-422 transceiver |
| Tension d'alimentation | 3.3 V |
| Maximum Data Rate | 10 Mbps |
| Driver Count | 1 |
| Receiver Count | 1 |
| Communication Mode | Half-duplex |
| Supported Standards | RS-485 and RS-422 |
| Driver Edge Rate | Slew-rate limited |
| Boîtier | 8-pin SOIC |
| Type de montage | Surface mount |
| Protection | Thermal protection |
| Maximum Bus Population | 256 devices |
| Power Class | Low-power transceiver |
Guide de configuration des broches du MAX3485ESA/GG8 8-pin soic
Configuration des broches du MAX3485ESA/GG8 (boîtier 8-pin soic). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour MAX3485ESA/GG8.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MAX3485ESA/GG8 convient pour 6 applications: Industrial Sensor and Actuator Networks, Building Automation Controller Nodes, Data Acquisition and Instrumentation, Motor-Control and Power-System Monitoring, RS-422 Point-to-Point Links, Embedded Communications Gateways.
Industrial Sensor and Actuator Networks
The MAX3485ESA/GG8 fits industrial RS-485 nodes that connect remote sensors, actuators, and controllers over a shared differential bus. Its 3.3 V supply integrates easily with modern embedded logic, while one driver and one receiver support half-duplex communication. The 10 Mbps maximum rate provides substantial bandwidth for short factory links, and the slew-rate-limited driver helps reduce edge-related EMI. Bus design must still include correct termination at the physical endpoints, suitable grounding, and controlled driver-enable timing to prevent multiple transmitters from driving the bus simultaneously.
Recommandé
Building Automation Controller Nodes
The MAX3485ESA/GG8 can connect a building controller to distributed room sensors, lighting modules, and HVAC actuators using an RS-485 backbone. Its low-power 3.3 V operation suits compact controller boards, and the differential driver and receiver improve noise immunity compared with single-ended signaling. The 10 Mbps capability is useful for local floor-level networks with moderate cable lengths. Designers should separate the communications pair from motor and relay wiring, keep the two bus nodes at the physical ends, and verify that the transceiver’s common-mode range matches the building’s grounding architecture.
Recommandé
Data Acquisition and Instrumentation
The MAX3485ESA/GG8 is appropriate for laboratory and industrial instrumentation that exchanges commands and measurements with remote data-acquisition equipment. The receiver and driver provide a compact differential interface without requiring separate line-driver circuitry. A 10 Mbps limit supports high-speed instrument traffic when cable length and topology permit, while the controlled driver edge rate can reduce common-mode disturbance. Use a twisted differential pair, maintain a dependable reference connection between systems, and confirm that the selected baud rate remains within the complete bus’s practical distance and loading envelope.
Recommandé
Motor-Control and Power-System Monitoring
The MAX3485ESA/GG8 can carry supervisory data between a controller and monitoring electronics in motor-drive or power-conversion equipment. Differential signaling helps preserve data integrity when the communication path shares an enclosure with switching nodes, relays, and high-current power stages. The transceiver’s 10 Mbps capability is ample for control and status traffic, but edge rate and cable routing still influence electromagnetic compatibility. Keep the pair away from motor phases and power inductors, use chassis or signal-ground strategies appropriate to the installation, and analyze grounding to prevent common-mode voltage from exceeding the device operating range.
Recommandé
RS-422 Point-to-Point Links
The MAX3485ESA/GG8 supports RS-422 point-to-point communication by using its integrated driver for the transmitting endpoint and its receiver at the remote endpoint. The 3.3 V interface is compatible with compact control and data-processing assemblies, while the 10 Mbps rate allows high-speed command or measurement links over suitable cable lengths. The protocol normally has one active driver, reducing contention concerns. Nevertheless, cable impedance, stub length, grounding, and connector pin assignment remain important, and the receiver output should be checked against the logic thresholds of the connected system.
Recommandé
Embedded Communications Gateways
The MAX3485ESA/GG8 can serve as the field-side interface on an embedded gateway that converts a legacy differential bus into a local processor or network engine. Its small 8-pin SOIC footprint preserves board area, and the integrated driver and receiver simplify the analog interface section. The 10 Mbps capability supports demanding field buses, while slew-rate limiting helps control cable reflections and radiated emissions. The gateway should isolate high-energy surge paths appropriately, provide a defined driver-enable sequence during direction changes, and test the complete interface across temperature, cable-length, and grounding variations.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MAX3485ESA/GG8 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | SP3485 |
|---|---|---|
| Brand | Analog Devices | MaxLinear |
| Package | 8-pin SOIC | 8-pin SOIC - same |
| Supply Voltage | 3.3 V | 3.3 V |
| Supported Interfaces | RS-485 and RS-422 | RS-485/RS-422 |
| Driver and Receiver Count | 1 driver and 1 receiver | 1 driver and 1 receiver |
Principaux différenciateurs
- Maintains Analog Devices component identity (vs SP3485)
- Defined 10 Mbps operating rate (vs SP3485)
- Compact 8-pin SOIC integration (vs SP3485)
Notes de conception
Route the differential pair as a tightly coupled pair with continuous reference to the associated ground plane. Keep the driver and receiver traces short, avoid right-angle changes, and place protection or filtering components where their surge current can return safely through the ground structure. The MAX3485’s 10 Mbps capability does not remove the need for controlled impedance and short stub branches.
Install bus termination only at the two physical endpoints of the main RS-485 cable. Do not terminate every node, because excess loading can reduce signal margin. Confirm termination resistance against the transceiver’s output and receiver-loading characteristics, and place the components close enough to the connector or line-driver pins to limit added stub length.
In a half-duplex design, guarantee that only one driver is enabled at a time. Include adequate dead time between transmit and receive modes so the bus can settle before the receiver interprets residual signal as data. Avoid using MAX3485ESA/GG8-T tape-and-reel packaging as an electrical substitute for the specified orderable part, and verify the exact suffix before release.
The slew-rate-limited driver helps reduce high-frequency common-mode energy, but it does not replace correct EMC layout. Separate the bus pair from switching-power paths, relay contacts, and motor wiring, and use a suitable enclosure or chassis-ground strategy for exposed cables. Verify radiated and conducted emissions with the final cable, connectors, grounding, and enclosure configuration.
Informations de conformité
The MAX3485 is an industrial interface IC rather than an automotive-qualified device, so AEC-Q100 is not applicable. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations should be confirmed from the current manufacturer product documentation.