Analog Devices

MAX3485ESA/GG8 - 3.3V 10Mbps RS-485 Transceiver | Analog Devices

MPN: MAX3485ESA/GG8 ✓ פעיל
3.3 V Vdss RS-485 and RS-422 Rds(on) 8-pin SOIC Package
כמות הזמנה מינימלית: 1 |

MAX3485ESA/GG8 סקירה

The Analog Devices MAX3485ESA/GG8 is a 3.3 V, low-power, half-duplex RS-485 and RS-422 transceiver rated for data rates up to 10 Mbps in an 8-pin SOIC package. Each device integrates one driver and one receiver, allowing a compact node to support bidirectional communication over a differential bus. Its slew-rate-limited driver is designed to reduce unwanted signal transitions, electromagnetic interference, and cable reflections associated with faster edge rates. The transceiver is suited to industrial equipment, data acquisition systems, building controls, and long-distance serial networks.

An RS-485 transceiver is an interface IC that converts logic-level signals into differential differential-pair voltages for reliable communication over noisy or long cables. It also converts received differential signals back into CMOS-compatible logic. The MAX3485 family occupies the interface IC layer within communication systems and combines a line driver, line receiver, and bus-management functions in one package. Its 3.3 V supply supports compact industrial, instrumentation, and embedded-control designs operating from modern low-voltage logic rails.

Key operating characteristics include 3.3 V power, a maximum data rate of 10 Mbps, one driver and one receiver, and an 8-pin SOIC footprint. The MAX3485ESA/GG8 is identified as the manufacturer’s extended-temperature part ordering code. The product family description also identifies low-power operation and thermal protection. These characteristics make the device useful where space, bus speed, reduced edge-rate emissions, and dependable differential signaling are more important than integrating multiple protocol-specific interface functions.

The integrated driver and receiver support half-duplex RS-485 networks in which a node transmits and receives on the same pair. RS-422 systems can also use the driver and receiver, although the two protocols have different network topologies and driver-enable expectations. The differential signal method improves noise immunity because the receiver evaluates the voltage difference between the two conductors rather than relying on a single conductor referenced only to ground. That principle is especially valuable around motors, relays, switching supplies, and long cables.

Typical uses include multi-drop industrial measurement buses, factory-floor controllers, building automation nodes, instrument interfaces, and embedded serial links between a controller and a remote sensor or actuator. A bus may accommodate as many as 256 devices when the complete system is designed for that population, including appropriate termination, biasing, cable length, topology, and data-rate limits. Device count alone does not guarantee successful communication because the complete bus topology must satisfy the selected transceiver’s electrical requirements.

The principal design consideration is the relationship between data rate, cable length, topology, termination, and driver edge rate. Keep the differential route compact, use a continuous ground reference where system architecture permits, place termination only at the physical ends of the bus, and verify the driver-enable timing in half-duplex designs. This page consolidates the device’s operating characteristics, package information, application guidance, pinout-status disclosure, and a verified functional-equivalent candidate to support faster engineering review.

חלופות תחליף ישיר עבור MAX3485ESA/GG8 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם MAX3485ESA/GG8 (אותו גורם צורה וטביעת רגל) — שונים ב Product Type, Mounting Type, Package, Supported Standards.

Analog Devices
Product Type: RS-485/RS-422 interface transceiver
Mounting Type: Through-hole
Package: 8-pin PDIP
MaxLinear
Product Type: RS-422/RS-485 half-duplex line transceiver

SP3485CN-L

✅ Drop-In
MaxLinear
📦 8-pin SOIC
RS-422/RS-485 half-duplex line transceiver · 1 driver · 1 receiver · Half-duplex · RS-422 and RS-485 · 10,000 kbit/s · 3.3 V · 3.135 V

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

MAX3485ESA/GG8 מפרטים

Product Type RS-485/RS-422 transceiver
מתח אספקה 3.3 V
Maximum Data Rate 10 Mbps
Driver Count 1
Receiver Count 1
Communication Mode Half-duplex
Supported Standards RS-485 and RS-422
Driver Edge Rate Slew-rate limited
מארז 8-pin SOIC
סוג הרכבה Surface mount
Protection Thermal protection
Maximum Bus Population 256 devices
Power Class Low-power transceiver

מדריך תצורת פינים של MAX3485ESA/GG8 8-pin soic

תצורת פינים עבור MAX3485ESA/GG8 (מארזת 8-pin soic). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.

תרשים פינים של מארזת 8-pin soic עבור MAX3485ESA/GG8

אין נתוני פריסת פינים מפורטים עבור MAX3485ESA/GG8.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

MAX3485ESA/GG8 מתאים עבור 6 יישוםs: Industrial Sensor and Actuator Networks, Building Automation Controller Nodes, Data Acquisition and Instrumentation, Motor-Control and Power-System Monitoring, RS-422 Point-to-Point Links, Embedded Communications Gateways.

🏭

Industrial Sensor and Actuator Networks

The MAX3485ESA/GG8 fits industrial RS-485 nodes that connect remote sensors, actuators, and controllers over a shared differential bus. Its 3.3 V supply integrates easily with modern embedded logic, while one driver and one receiver support half-duplex communication. The 10 Mbps maximum rate provides substantial bandwidth for short factory links, and the slew-rate-limited driver helps reduce edge-related EMI. Bus design must still include correct termination at the physical endpoints, suitable grounding, and controlled driver-enable timing to prevent multiple transmitters from driving the bus simultaneously.

🏭

Building Automation Controller Nodes

The MAX3485ESA/GG8 can connect a building controller to distributed room sensors, lighting modules, and HVAC actuators using an RS-485 backbone. Its low-power 3.3 V operation suits compact controller boards, and the differential driver and receiver improve noise immunity compared with single-ended signaling. The 10 Mbps capability is useful for local floor-level networks with moderate cable lengths. Designers should separate the communications pair from motor and relay wiring, keep the two bus nodes at the physical ends, and verify that the transceiver’s common-mode range matches the building’s grounding architecture.

🔧

Data Acquisition and Instrumentation

The MAX3485ESA/GG8 is appropriate for laboratory and industrial instrumentation that exchanges commands and measurements with remote data-acquisition equipment. The receiver and driver provide a compact differential interface without requiring separate line-driver circuitry. A 10 Mbps limit supports high-speed instrument traffic when cable length and topology permit, while the controlled driver edge rate can reduce common-mode disturbance. Use a twisted differential pair, maintain a dependable reference connection between systems, and confirm that the selected baud rate remains within the complete bus’s practical distance and loading envelope.

⚡

Motor-Control and Power-System Monitoring

The MAX3485ESA/GG8 can carry supervisory data between a controller and monitoring electronics in motor-drive or power-conversion equipment. Differential signaling helps preserve data integrity when the communication path shares an enclosure with switching nodes, relays, and high-current power stages. The transceiver’s 10 Mbps capability is ample for control and status traffic, but edge rate and cable routing still influence electromagnetic compatibility. Keep the pair away from motor phases and power inductors, use chassis or signal-ground strategies appropriate to the installation, and analyze grounding to prevent common-mode voltage from exceeding the device operating range.

🌐

RS-422 Point-to-Point Links

The MAX3485ESA/GG8 supports RS-422 point-to-point communication by using its integrated driver for the transmitting endpoint and its receiver at the remote endpoint. The 3.3 V interface is compatible with compact control and data-processing assemblies, while the 10 Mbps rate allows high-speed command or measurement links over suitable cable lengths. The protocol normally has one active driver, reducing contention concerns. Nevertheless, cable impedance, stub length, grounding, and connector pin assignment remain important, and the receiver output should be checked against the logic thresholds of the connected system.

🖥️

Embedded Communications Gateways

The MAX3485ESA/GG8 can serve as the field-side interface on an embedded gateway that converts a legacy differential bus into a local processor or network engine. Its small 8-pin SOIC footprint preserves board area, and the integrated driver and receiver simplify the analog interface section. The 10 Mbps capability supports demanding field buses, while slew-rate limiting helps control cable reflections and radiated emissions. The gateway should isolate high-energy surge paths appropriately, provide a defined driver-enable sequence during direction changes, and test the complete interface across temperature, cable-length, and grounding variations.

סיכום מוצרים מומלצים

MAX3483 Related low-power RS-485/RS-422 transceiver family member בשימוש ב-: Industrial Sensor and Actuator Networks, Motor-Control and Power-System Monitoring MAX3486 Related RS-485/RS-422 transceiver family member בשימוש ב-: Industrial Sensor and Actuator Networks, Data Acquisition and Instrumentation, Embedded Communications Gateways MAX3488 Related slew-rate-limited RS-485/RS-422 transceiver בשימוש ב-: Building Automation Controller Nodes, Motor-Control and Power-System Monitoring MAX3490 Related 3.3 V low-power transceiver בשימוש ב-: Building Automation Controller Nodes, RS-422 Point-to-Point Links MAX3491 Related 3.3 V RS-485/RS-422 transceiver בשימוש ב-: Data Acquisition and Instrumentation, RS-422 Point-to-Point Links MAX3485 Base transceiver family for gateway interface designs בשימוש ב-: Embedded Communications Gateways
What is the MAX3485ESA/GG8?
The MAX3485ESA/GG8 is a 3.3 V, half-duplex RS-485 and RS-422 transceiver manufactured by Analog Devices. It combines one driver and one receiver in an 8-pin SOIC package and supports data rates up to 10 Mbps. According to the manufacturer’s MAX3485 product page, the MAX3485 family is intended for low-power differential serial communication in industrial and embedded systems.
What are the key specifications of MAX3485ESA/GG8 that engineers should know?
The MAX3485ESA/GG8 operates from a 3.3 V supply, supports RS-485 and RS-422 communication, and provides one driver and one receiver in an 8-pin SOIC package. Its maximum listed data rate is 10 Mbps, and its driver is slew-rate limited to help control edge-related EMI and cable reflections. The manufacturer also identifies thermal protection and low-power operation as family-level features.
What is the operating voltage of MAX3485ESA/GG8?
The MAX3485ESA/GG8 operates from a 3.3 V supply. The Analog Devices product page identifies the MAX3485 as a 3.3 V transceiver, and the manufacturer’s datasheet title describes the family as a 3.3 V-powered RS-485/RS-422 interface. Use the device with logic and system rails compatible with a 3.3 V supply while checking the complete datasheet limits before final circuit release.
What is the maximum data rate of MAX3485ESA/GG8?
The MAX3485ESA/GG8 supports data rates up to 10 Mbps. Analog Devices describes the MAX3485 family as a 3.3 V, low-power RS-485 and RS-422 transceiver, while the product listing identifies the device as a 10 Mbps interface IC. Maximum data rate does not guarantee that every cable length or topology can operate at that rate.
Where can I download the MAX3485ESA datasheet PDF?
The official MAX3485 product page provides access to the Analog Devices MAX3485 datasheet and related technical documents. Use https://www.analog.com/en/products/max3485.html as the authoritative starting point for the PDF, pin descriptions, electrical characteristics, and ordering information. The MAX3485ESA/GG8 ordering code should be matched against the relevant table before release.
Where is the MAX3485ESA pinout?
The MAX3485ESA pinout is located in the pin-description and package-drawing sections of the Analog Devices MAX3485 datasheet. The device is an 8-pin SOIC, and its external connections include supply, ground, driver input and enable, driver output, receiver input, and receiver output. The manufacturer datasheet should be used for the exact numbered terminal arrangement and exposed-pad details before PCB routing.
Can MAX3485ESA/GG8 be used in an RS-485 network?
Yes, the MAX3485ESA/GG8 can be used in RS-485 networks because it integrates an RS-485-compatible driver and receiver. Its half-duplex configuration allows a node to share one differential pair for transmission and reception. The complete bus still requires suitable termination, fail-safe biasing where needed, correct topology, and adequate common-mode compatibility.
What is the difference between RS-485 and RS-422 operation with MAX3485ESA/GG8?
RS-485 is suited to multipoint buses in which multiple drivers may be connected with careful addressing and tri-state control, while RS-422 normally uses a point-to-point driver-to-receiver arrangement. The MAX3485ESA/GG8 provides the driver and receiver needed for either wiring style. Protocol compliance still depends on enable control, cable topology, termination, grounding, and the selected operating mode.
What can replace the MAX3485ESA/GG8?
The SP3485 from MaxLinear is identified as a functional-equivalent, pin-compatible alternative to the MAX3485ESA. It operates as a 3.3 V RS-485/RS-422 transceiver in the same 8-pin SOIC format and adds a stated 2 kV ESD-protection feature. Before substitution, compare the complete electrical tables, propagation timing, receiver thresholds, temperature range, and shutdown behavior against the design requirements.
Is the SP3485 the same as the MAX3485ESA/GG8?
The SP3485 is a pin-compatible functional equivalent, but it is not the same manufacturer’s orderable part. MaxLinear’s cross-reference information identifies it as an equivalent for the MAX3485ESA and specifically notes 2 kV ESD protection. The MAX3485ESA/GG8 remains the appropriate choice when exact manufacturer continuity, qualification records, or approved-source part identity are required.
When should I choose MAX3485ESA/GG8 over the SP3485?
Choose the MAX3485ESA/GG8 when maintaining Maxim Integrated or Analog Devices part identity is important to your qualification process, approved-vendor list, or existing product documentation. Choose the SP3485 when its stated 2 kV ESD capability and verified electrical characteristics meet the design better. Both use the same 8-pin SOIC format, but functional equivalence does not guarantee identical timing or every operating limit.
Is the MAX3485ESA/GG8 suitable for industrial automation systems?
The MAX3485ESA/GG8 is suitable for industrial automation systems that require a 3.3 V RS-485 or RS-422 interface. Its 10 Mbps capability, one driver, one receiver, slew-rate-limited output, and thermal protection fit compact controller, sensor, and remote-I/O nodes. Industrial suitability still depends on the complete system’s temperature, surge, isolation, grounding, and EMC requirements.
How should MAX3485ESA/GG8 termination and grounding be designed?
Place RS-485 termination resistors only at the two physical ends of the main bus, and determine their resistance from the driver’s specified output and receiver loading characteristics. Maintain a low-impedance return path between connected systems, and avoid routing the differential pair alongside high-current or high-voltage switching paths. Confirm the complete topology and maximum cable length against the final data rate.
Where can I buy MAX3485ESA/GG8 and check current lead time?
Use the Request a Quote form on this page to request current availability, MOQ, lead time, and orderable packaging for MAX3485ESA/GG8. The request identifies the exact 3.3 V, 10 Mbps, 8-pin SOIC transceiver and avoids confusion with the separate MAX3485ESA+ and MAX3485ESA/GG8-T ordering codes. Quote terms can change with demand and manufacturing conditions.
What is the price of MAX3485ESA/GG8?
The current commercial price for MAX3485ESA/GG8 should be requested through the Request a Quote form on this page. The form can return pricing for the exact MAX3485ESA/GG8 ordering code, required quantity, and shipping destination. This avoids presenting a stale figure or confusing this 8-pin SOIC variant with MAX3485ESA+ or MAX3485ESA/GG8-T.
Is MAX3485ESA/GG8 in stock?
Current stock for MAX3485ESA/GG8 should be confirmed through the Request a Quote form on this page. Include the required quantity, reel or cut-tape preference, and destination so the supplier can respond with a meaningful availability and lead-time statement. Inventory can change rapidly, so confirm the exact MAX3485ESA/GG8 suffix before placing an order.

נתוני עזר הנדסיים עבור MAX3485ESA/GG8 — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the MAX3485ESA/GG8 when your design needs a 3.3 V, 10 Mbps, half-duplex RS-485/RS-422 transceiver in an 8-pin SOIC package and maintaining Analog Devices or Maxim Integrated part identity is important. Its integrated driver and receiver suit compact industrial nodes, while the slew-rate-limited output helps control edge-related EMI and reflections. The SP3485 is the closest documented alternative: MaxLinear identifies it as a functional-equivalent, pin-compatible device and specifies 2 kV ESD protection. Consider it when that protection feature or its detailed electrical characteristics better match the design. Before substitution, compare propagation delay, receiver thresholds, fail-safe behavior, driver-enable timing, temperature range, and package dimensions. Neither part eliminates the need for correct bus termination, grounding, common-mode analysis, or controlled half-duplex turnaround.

השוואה עם חלופות

פרמטר מוצר זה SP3485
Brand Analog Devices MaxLinear
Package 8-pin SOIC 8-pin SOIC - same
Supply Voltage 3.3 V 3.3 V
Supported Interfaces RS-485 and RS-422 RS-485/RS-422
Driver and Receiver Count 1 driver and 1 receiver 1 driver and 1 receiver

מבדילים עיקריים

  • Maintains Analog Devices component identity (לעומתSP3485)
  • Defined 10 Mbps operating rate (לעומתSP3485)
  • Compact 8-pin SOIC integration (לעומתSP3485)

הערות תכנון

Route the differential pair as a tightly coupled pair with continuous reference to the associated ground plane. Keep the driver and receiver traces short, avoid right-angle changes, and place protection or filtering components where their surge current can return safely through the ground structure. The MAX3485’s 10 Mbps capability does not remove the need for controlled impedance and short stub branches.

Install bus termination only at the two physical endpoints of the main RS-485 cable. Do not terminate every node, because excess loading can reduce signal margin. Confirm termination resistance against the transceiver’s output and receiver-loading characteristics, and place the components close enough to the connector or line-driver pins to limit added stub length.

In a half-duplex design, guarantee that only one driver is enabled at a time. Include adequate dead time between transmit and receive modes so the bus can settle before the receiver interprets residual signal as data. Avoid using MAX3485ESA/GG8-T tape-and-reel packaging as an electrical substitute for the specified orderable part, and verify the exact suffix before release.

The slew-rate-limited driver helps reduce high-frequency common-mode energy, but it does not replace correct EMC layout. Separate the bus pair from switching-power paths, relay contacts, and motor wiring, and use a suitable enclosure or chassis-ground strategy for exposed cables. Verify radiated and conducted emissions with the final cable, connectors, grounding, and enclosure configuration.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

The MAX3485 is an industrial interface IC rather than an automotive-qualified device, so AEC-Q100 is not applicable. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations should be confirmed from the current manufacturer product documentation.

חיפושים קשורים

max3485esa datasheet max3485esa t datasheet umw max3485esa max3485esa hlf max3485esa schematic max3485esa pinout max3485esa pdf MAX3485ESA/GG8 datasheet MAX3485ESA/GG8 pinout MAX3485ESA/GG8 equivalent MAX3485ESA/GG8 replacement MAX3485ESA/GG8 price MAX3485ESA/GG8 stock MAX3485ESA/GG8 schematic MAX3485ESA/GG8 vs SP3485

רכיבים ומונחים קשורים

Analog Devices MAX3485ESA/GG8 MAX3485 SP3485 MaxLinear RS-485 transceiver RS-422 transceiver half-duplex transceiver differential line driver differential line receiver interface IC 3.3 V transceiver 10 Mbps data rate slew-rate-limited driver 8-pin SOIC SOIC package family surface-mount package industrial automation building automation data acquisition motor control point-to-point RS-422 bus termination embedded gateway EMI
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר