Analog Devices

MAX398EGE - 8:1 Low-Voltage CMOS Analog Multiplexer | Analog Devices

Référence : MAX398EGE ✓ Actif
Less than 100 ohm Rds(on) 16-pin QFN, 4 mm x 4 mm Package
MOQ : 1 |

MAX398EGE Présentation

Analog Devices MAX398EGE is an 8:1 precision, low-voltage CMOS analog multiplexer with less than 100 Ω on-resistance, channel-to-channel matching within 6 Ω, and on-resistance variation limited to 11 Ω maximum over the specified analog signal range. It is supplied in a 16-pin QFN package. The device routes one analog signal source to one of eight inputs, making it useful for precision measurement, signal conditioning, test systems, data acquisition, and instrumentation.

An analog multiplexer is an analog switch array that connects a common terminal to one selected input channel. Within the interface-IC hierarchy, the MAX398EGE belongs to the analog switch and multiplexer family, where low and closely matched on-resistance reduce channel-dependent attenuation and error. Its monolithic CMOS construction is intended for low-voltage analog routing where repeatable channel behavior and compact implementation are important.

The primary performance specifications emphasize resistance matching rather than resistance alone. Less than 100 Ω on-resistance limits insertion loss in the selected path, while matching within 6 Ω minimizes gain differences as the selected input changes. The 11 Ω maximum change across the specified analog range further limits signal-level distortion when the mux handles varying amplitudes. The 8:1 configuration also reduces the number of external routing connections required in multichannel analog front ends.

The MAX398 part family is offered as an 8-channel or dual 4-channel precision multiplexer. This distinction matters because an 8:1 device presents eight selection inputs, while the dual 4:1 arrangement divides its resources into two independent 4:1 muxes. Circuit designers must therefore confirm pin-level functions, control logic, and package suffix before treating family members as substitutes. The MAX398EGE is the 8:1 member in the exact ordered variant identified here.

Typical uses include multichannel sensor acquisition, automated test equipment, battery-cell measurement, industrial control systems, and laboratory instrumentation. In these systems, the common analog path can be connected successively to different sensors or test nodes while the surrounding ADC or measurement front end processes the selected signal. The low matched on-resistance helps preserve amplitude consistency across channels.

PCB design should account for the QFN package, exposed thermal pad requirements, supply bypassing, and analog return-current paths. Keep the multiplexed signal traces short, use a continuous ground reference, and place input and bypass capacitors close to their associated pins. Review the MAX398EGE datasheet pin description table before assigning control and signal functions because the 16-pin layout includes multiple selection and common connections.

This product record combines the manufacturer overview with package and circuit-level guidance, identifies verified drop-in alternatives where they exist, and adds practical selection criteria for analog routing. It distinguishes confirmed electrical characteristics from parameters that still require confirmation for a production design, helping engineers evaluate the MAX398EGE before layout release.

Alternatives de remplacement direct pour MAX398EGE — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Aucune alternative de remplacement direct disponible pour ce produit.

Demander des alternatives

MAX398EGE Spécifications

Multiplexer Configuration 8:1
Number of Channels 8 channels
On-Resistance Less than 100 ohm
On-Resistance Channel Matching Within 6 ohm between channels
On-Resistance Variation Over Analog Signal Range 11 ohm maximum
Device Type Precision monolithic CMOS analog multiplexer
Supported Multiplexing Arrangement 8-channel or dual 4-channel in the MAX398/MAX399 family
Boîtier 16-pin QFN, 4 mm x 4 mm
Type de montage Surface mount
Circuit Count 1 circuit
On-Resistance Flatness Flat over the specified analog signal range
Manufacturer Product Status Production

Guide de configuration des broches du MAX398EGE 16-pin qfn, 4 mm x 4 mm

Configuration des broches du MAX398EGE (boîtier 16-pin qfn, 4 mm x 4 mm). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.

Schéma de brochage du boîtier 16-pin qfn, 4 mm x 4 mm pour le MAX398EGE

Aucune donnée de brochage détaillée disponible pour MAX398EGE.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

MAX398EGE convient pour 6 applications: Multichannel Sensor Acquisition, Automated Test Equipment, Battery Cell Monitoring, Industrial Control Signal Routing, Laboratory Instrumentation, Data Acquisition Systems.

🧩

Multichannel Sensor Acquisition

The MAX398EGE fits multichannel sensor acquisition because it routes one of eight analog inputs to a common measurement path while maintaining less than 100 Ω on-resistance. Its channel matching within 6 Ω helps reduce gain variation when different sensors are selected in succession. An ADC front end can use the common output as its analog input while digital control lines select the measured channel. Designers should confirm that every sensor signal remains within the specified analog range and should account for source impedance, ADC input topology, and the mux's contribution to signal attenuation.

🏭

Automated Test Equipment

The MAX398EGE is appropriate for automated test equipment that must connect several test points to one measurement instrument channel. Its 8:1 configuration reduces external routing complexity, while the 11 Ω maximum on-resistance variation over the specified analog range helps maintain signal consistency as input amplitude changes. The common terminal can feed an ADC, comparator, or precision measurement front end. For accurate results, keep the analog path short, provide a low-impedance downstream input, and verify that switch resistance and channel matching fit the required measurement tolerance.

⚡

Battery Cell Monitoring

The MAX398EGE can route multiple battery-cell or balancing-monitor inputs into a shared analog measurement chain. Its low on-resistance reduces the voltage drop introduced between the selected cell node and the measurement input, while close channel matching improves consistency when different cells are scanned. The compact QFN implementation also supports space-constrained monitoring boards. The design must remain within the specified analog signal range, include appropriate protection and isolation, and provide a stable reference and ADC front end for accurate cell-voltage measurements.

🏭

Industrial Control Signal Routing

The MAX398EGE fits industrial control boards that must select among several analog command or sensor lines. The 8:1 topology consolidates analog routing while the less-than-100 Ω on-resistance helps limit loading of the selected source. Matching within 6 Ω supports repeatable channel behavior across a control loop. Engineers should verify common-mode limits, supply requirements, control timing, and system grounding, and should place the device near the analog source when trace length or source impedance could otherwise increase error.

🖥️

Laboratory Instrumentation

The MAX398EGE is useful in laboratory instruments that switch several external or internal test signals onto a common precision input. Closely matched on-resistance helps prevent channel selection from producing substantial gain changes, and the 11 Ω maximum variation supports predictable behavior over the analog range. A compact 16-pin QFN also allows the multiplexer to sit near sensitive analog circuitry. For best results, use a low-noise reference, clean supply bypassing, short signal paths, and a downstream circuit whose input impedance does not create excessive divider error.

📡

Data Acquisition Systems

The MAX398EGE supports compact data-acquisition systems requiring eight analog inputs but only one downstream conversion channel. Select lines can scan the inputs sequentially, while the common output feeds an ADC or analog front end. The specified low on-resistance and tight channel matching help minimize input-dependent attenuation and improve repeatability between scans. Designers should select a sampling scheme compatible with the mux's switching behavior, establish acquisition time for the ADC, and place the device to minimize coupling from digital select lines into the analog path.

Récapitulatif des produits recommandés

MAX398 Precision 8-channel CMOS analog multiplexer family Utilisé dans : Multichannel Sensor Acquisition, Automated Test Equipment, Battery Cell Monitoring, Industrial Control Signal Routing, Laboratory Instrumentation, Data Acquisition Systems MAX399 Dual 4-channel family option for parallel routing Utilisé dans : Multichannel Sensor Acquisition, Automated Test Equipment, Battery Cell Monitoring, Industrial Control Signal Routing, Laboratory Instrumentation, Data Acquisition Systems
What is the MAX398EGE?
The MAX398EGE is a precision, 8:1, low-voltage CMOS analog multiplexer in a 16-pin QFN package. According to the Analog Devices MAX398 product page, its on-resistance is less than 100 Ω, channel matching is within 6 Ω, and resistance variation over the specified analog range is no more than 11 Ω. It connects a common analog node to one selected input among eight channels.
What are the key specifications of MAX398EGE that engineers should know?
The MAX398EGE is an 8:1 precision analog multiplexer with less than 100 Ω on-resistance and channel-to-channel matching within 6 Ω. The Analog Devices MAX398 overview also specifies a maximum on-resistance change of 11 Ω over the supported analog signal range. The device uses a monolithic CMOS construction and is offered in a 16-pin, 4 mm by 4 mm QFN package.
How do MAX398EGE and MAX398EPE differ?
The MAX398EGE and MAX398EPE implement the same MAX398 8:1 multiplexing function, but their package suffixes indicate different physical packages. The MAX398EGE is identified as a 16-pin QFN, whereas the MAX398EPE listing identifies a 16-pin DIP package. Because their footprints differ, MAX398EPE is not a drop-in replacement for MAX398EGE without a PCB redesign.
Can MAX398ESE+ replace MAX398EGE?
No. The MAX398ESE+ is listed in a 16-pin SOIC package, while the MAX398EGE is a 16-pin QFN. Both belong to the MAX398 family, but their land patterns are not interchangeable. Installing the MAX398ESE+ on a MAX398EGE board would require component placement and routing changes rather than a direct drop-in substitution.
Where can I download the MAX398EGE datasheet PDF?
The MAX398EGE datasheet and related documentation are available through the official Analog Devices MAX398 product page at https://www.analog.com/en/products/max398.html. The page identifies the data sheet as revision 6 and provides the family documentation needed to review the 8-channel and dual 4-channel configurations. Always use the manufacturer document when assigning pins and selecting electrical limits.
Where can I find the MAX398EGE pinout?
The MAX398EGE pinout is documented in the pin-description section of the MAX398 manufacturer data sheet. Use the official Analog Devices MAX398 page to access that document and the MAX398EGE ordering table. The exact 16-pin QFN footprint contains control and analog-routing functions that must be checked against the selected suffix before a PCB is released.
What is the best drop-in replacement for MAX398EGE?
No independently verified drop-in replacement for the exact MAX398EGE configuration was identified. Parts named MAX398EPE and MAX398ESE+ use different packages, and the MAX399 family member uses a dual 4:1 arrangement rather than the MAX398 8:1 pin function. A replacement should therefore be selected only after a manufacturer confirms identical pinout, logic levels, supply range, and electrical limits.
Is MAX398EGE suitable for multichannel sensor acquisition?
The MAX398EGE is suitable for multichannel sensor acquisition when its specified analog range covers the sensor signals. Its less-than-100 Ω on-resistance and within-6 Ω channel matching help limit input-dependent attenuation and channel-to-channel gain variation. The common output can feed an ADC front end while the select logic routes eight analog inputs sequentially.
When should I choose MAX398EGE instead of a dual 4:1 multiplexer?
Choose the MAX398EGE when a design must route one of eight inputs to a common analog terminal and the board has room for its 16-pin QFN footprint. A dual 4:1 multiplexer is more appropriate when two independent four-channel groups are required simultaneously. The selection also depends on control logic, supply voltage, signal range, and exact pin compatibility rather than function alone.
What is the difference between MAX398 and MAX399?
The MAX398 is the 8-channel version of the precision low-voltage CMOS multiplexer family, while MAX399 is the dual 4-channel version. Both are described as monolithic devices with low, closely matched on-resistance, but their control and analog-routing arrangements differ. The distinction prevents treating MAX399 as a drop-in replacement for the 8:1 MAX398EGE.
How does the MAX398EGE affect measurement accuracy?
The MAX398EGE affects measurement accuracy through its on-resistance and channel matching. Insertion loss is set by the less-than-100 Ω resistance, while the within-6 Ω matching limits gain variation between selected channels. The 11 Ω maximum variation across the specified analog range also limits signal-dependent error. Overall accuracy still depends on ADC resolution, source impedance, leakage, and the reference used by the system.
What PCB layout practices are important for MAX398EGE?
Place bypass capacitors close to the supply pins, keep the multiplexed analog trace short, and maintain a continuous ground plane beneath the QFN footprint. Route the common analog node away from digital select signals and high-impedance sensor connections. Thermal-pad assembly and solder requirements should follow the manufacturer's package drawing because the exposed pad is part of the 16-pin QFN implementation.
Is MAX398EGE in stock and what is its lead time?
Current stock, minimum order quantity, and production lead time should be requested through the Request a Quote form on this page. The manufacturer lists MAX398 as a production family, but that status alone does not establish current inventory for the exact MAX398EGE suffix. The quote request should state the required quantity, package form, date code needs, and destination.
Where can I buy MAX398EGE online?
Use the Request a Quote form on this page to request MAX398EGE availability, pricing, and lead time for the exact 16-pin QFN ordering code. The form avoids ambiguity between MAX398 package suffixes and provides a direct response for the exact manufacturer part number. Buyers should also confirm production status and delivery requirements before releasing a purchase order.
What is the price of MAX398EGE?
Current pricing for the exact MAX398EGE should be obtained through the Request a Quote form on this page. Package suffix, order quantity, date code, and delivery requirements can materially affect commercial terms, so pricing for another MAX398 variant is not a valid quote for this ordering code. The form is the appropriate channel for a transaction-ready response.
What is an Analog Devices equivalent for MAX398EGE?
The closest same-family Analog Devices option is another correctly packaged MAX398 variant only if the manufacturer confirms identical pinout, logic, supply voltage, and analog limits. The verified MAX398EPE and MAX398ESE+ variants are not drop-in equivalents because they use DIP and SOIC packages. No cross-brand part was verified as a same-footprint substitute for MAX398EGE.

Données de référence d'ingénierie pour MAX398EGE — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose MAX398EGE when the design requires eight analog inputs routed through one common channel and uses a 16-pin QFN layout. Its less-than-100 Ω on-resistance and within-6 Ω channel matching are useful when the downstream receiver has sufficiently high input impedance and the required measurement accuracy tolerizes switch resistance. MAX398EPE and MAX398ESE+ implement the same general 8:1 family function but require DIP or SOIC layouts, respectively, so neither is a drop-in substitute for the QFN board. MAX399 is preferable only when two independent 4:1 groups are needed, not as a direct replacement for the 8:1 pin arrangement. Before selection, confirm the supply range, logic thresholds, analog signal range, timing, exposed-pad construction, and complete 16-pin assignment from the manufacturer data sheet.

Comparaison avec les alternatives

Paramètre Ce produit
Package 16-pin QFN, 4 mm x 4 mm
Brand Analog Devices
Multiplexer Configuration 8:1
Number of Circuits 1 circuit
On-Resistance Less than 100 ohm
On-Resistance Matching Within 6 ohm between channels
On-Resistance Variation 11 ohm maximum over specified analog signal range
Device Architecture Precision monolithic CMOS analog multiplexer
Product Status Production

Principaux différenciateurs

  • Eight-channel routing in one device (vs MAX399)
  • Close channel-to-channel resistance matching (vs Generic low-resistance analog multiplexer)
  • Compact surface-mount footprint (vs MAX398EPE)
  • Smaller footprint than the SOIC variant (vs MAX398ESE+)

Notes de conception

Place the MAX398EGE close to the analog source or measurement front end and keep the common analog trace short. Route the eight input connections away from switching and clock signals to reduce capacitive coupling into the selected path. A continuous ground plane under and around the QFN is preferable to fragmented return paths, especially when the downstream circuit uses high-impedance inputs.

Include the switch on-resistance and downstream input impedance when calculating measurement attenuation. With a less-than-100 Ω on-resistance specification, a high-impedance receiver can experience meaningful division error. Confirm the analog signal range, use a high-input-impedance ADC front end, and evaluate settling time after changing the selected channel before taking successive samples.

Do not substitute MAX398EPE or MAX398ESE+ directly for MAX398EGE: the verified package variants are 16-pin DIP and 16-pin SOIC, respectively, while MAX398EGE uses a 16-pin QFN. Also do not treat the dual 4:1 MAX399 as a direct substitute. Confirm the exact ordering code, pin description table, control levels, supply limits, and exposed-pad assembly requirements.

Provide local supply bypassing and route it using the shortest practical path to the device's supply and ground pins. Decoupling requirements must be confirmed from the manufacturer data sheet because the exact voltage and capacitance values are not stated on the product overview. Maintain a low-impedance ground return and avoid sharing narrow return paths with high-current output circuitry.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The manufacturer overview identifies MAX398 as a production part but does not state the requested compliance classifications.

Données vérifiées le : 2026-11-14 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

MAX398EGE datasheet MAX398EGE pinout MAX398EGE datasheet pdf MAX398EGE equivalent MAX398EGE replacement MAX398EGE cross reference MAX398EGE vs MAX398EPE MAX398EGE footprint MAX398EGE application circuit MAX398EGE price MAX398EGE stock Analog Devices MAX398EGE MAX398 8:1 analog multiplexer MAX398 QFN-16 pinout

Composants & termes associés

Analog Devices MAX398EGE MAX398 MAX399 MAX398EPE MAX398ESE+ analog multiplexer analog switch multiplexer interface IC CMOS monolithic CMOS 8:1 multiplexing dual 4:1 multiplexing on-resistance channel matching common analog terminal QFN-16 surface mount SMD data acquisition automated test equipment sensor acquisition signal routing
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ