MAX398ESE+ - 8:1 100Ω CMOS Analog Multiplexer | Analog Devices
Référence : MAX398ESE+ ✓ ActifMAX398ESE+ Présentation
An analog multiplexer is a semiconductor switching device that connects multiple input channels to one shared output under digital control. It belongs to the analog switch and multiplexer hierarchy, which supports the broader field of interface ICs. By reducing the number of signal paths required on a circuit board, a multiplexed architecture can simplify wiring, conserve connector space, and support sequential acquisition from multiple sensors or test points.
The MAX398 family provides precision channel matching and low on-resistance variation. According to the manufacturer product information, on-resistance is matched within 6 Ω between channels, while the maximum change across the specified analog signal range is 11 Ω. These characteristics help minimize gain error and distortion when signals pass through the selected channel. The device also uses low-voltage CMOS circuitry and supports dual 4-channel operation in appropriate device configurations.
The MAX398ESE+ uses address and enable controls to select the active analog path. Its 8:1 organization allows one common output to be connected sequentially to eight source signals, reducing the number of analog switches required in multichannel systems. Signal integrity depends on keeping control traces short, using a stable low-impedance reference around the selected channel, and minimizing loading on the common output. Supply bypassing and grounding are especially important when low-level signals are measured.
Typical uses include audio-signal routing, battery-powered acquisition systems, automated test equipment, communication equipment, guidance and control systems, heads-up displays, military radios, PBX and PABX systems, and sample-and-hold circuits. The precision matching is valuable in data-acquisition and test systems where channel-to-channel consistency directly affects calibration accuracy and measurement repeatability.
Design the MAX398ESE+ with the required 3 V to 15 V operating range in mind and account for the voltage limits of every signal routed through the mux. Check the absolute maximum ratings and pin descriptions in the manufacturer datasheet before applying signals, especially when the analog input can exceed the selected supply rail.
This page combines the device architecture, operating limits, pin-level routing guidance, application analysis, and same-package replacement information to support faster component selection and PCB-level replacement decisions.
Alternatives de remplacement direct pour MAX398ESE+ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MAX398ESE+ (même facteur de forme et même empreinte) — différant par Mounting Type, ESD Protection, Multiplexer Configuration, On-Resistance, Package.
MAX398CSE+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX399ESE+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DG408
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →DG409DJ+
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →DG508A
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DG509A
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX398ESE+ Spécifications
| Multiplexer Configuration | 1 circuit, 8:1 |
| Number of Channels | 8 channels |
| On-Resistance | 100 Ω |
| On-Resistance Matching Between Channels | 6 Ω maximum |
| On-Resistance Variation Across Analog Signal Range | 11 Ω maximum |
| Supply Voltage Range | 3 V to 15 V |
| Device Architecture | Precision low-voltage CMOS analog multiplexer |
| Plage de température de fonctionnement | -40°C to +85°C |
| Boîtier | 16-pin NSOIC |
| Type de montage | Surface mount |
| Nombre de broches | 16 pins |
| Multiplexer Family | MAX398/MAX399 |
| Dual 4-Channel Configuration | Supported by the MAX398 family |
| Primary Application | Analog signal routing |
| Secondary Application | Low-voltage data acquisition |
Configuration des broches de MAX398ESE+
| Broche 1 | A0 — Address input A0 |
| Broche 2 | A1 — Address input A1 |
| Broche 3 | A2 — Address input A2 |
| Broche 4 | A3 — Address input A3 |
| Broche 5 | EN — Enable input |
| Broche 6 | S0 — Select input S0 |
| Broche 7 | S1 — Select input S1 |
| Broche 8 | GND — Ground |
| Broche 9 | S3 — Analog terminal S3 |
| Broche 10 | S4 — Analog terminal S4 |
| Broche 11 | S5 — Analog terminal S5 |
| Broche 12 | S6 — Analog terminal S6 |
| Broche 13 | S7 — Analog terminal S7 |
| Broche 14 | D — Common analog terminal |
| Broche 15 | V+ — Positive supply input |
| Broche 16 | V- — Negative supply input |
Applications typiques
MAX398ESE+ convient pour 6 applications: Automated Test Equipment, Low-Voltage Data Acquisition, Audio Signal Routing, Sample-and-Hold Systems, Battery-Powered Measurement Systems, Communication and Guidance Systems.
Automated Test Equipment
The MAX398ESE+ fits automated test equipment that must connect multiple test points to a shared measurement channel. Its 8:1 configuration reduces the number of analog switches and routing traces needed by the fixture, while the specified 6 Ω maximum channel-to-channel on-resistance matching helps limit calibration drift as the selected path changes. The device operates from 3 V to 15 V and supports -40°C to +85°C operation. Use it when the measured signals remain within the electrical limits of the mux and when the test system requires a common measurement amplifier or converter input. Designers should also evaluate input capacitance, leakage, switching time, and the selected instrumentation input impedance before finalizing the routing network.
Recommandé
Low-Voltage Data Acquisition
MAX398ESE+ is suitable for sequential sampling in low-voltage data-acquisition systems because one common output can select among eight analog sources. The 100 Ω on-resistance, 6 Ω maximum channel matching, and 11 Ω maximum variation across the analog signal range help reduce path-dependent attenuation in sensor and test-node measurements. Its 3 V to 15 V supply range supports compact mixed-signal systems, while its -40°C to +85°C rating supports a broad range of environments. The source impedance must be low enough to avoid excessive divider error introduced by the switch resistance. Confirm leakage, charge injection, off isolation, and acquisition settling time against the required measurement accuracy before using the mux directly with high-impedance sensors.
Recommandé
Audio Signal Routing
The MAX398ESE+ can route one of eight low-voltage audio or control signals to a common processing input. Its channel-to-channel resistance matching of 6 Ω maximum helps minimize level differences when the source changes, while its low-voltage CMOS implementation is appropriate for compact analog switching networks. The 3 V to 15 V operating range allows use in portable and embedded equipment, and its broad temperature rating supports environments beyond the 0°C to +70°C commercial range. Audio designs must still account for off impedance, channel isolation, switching transients, ground-loop risk, and the input impedance of the selected amplifier. Keep the analog path short and connect the bypass and reference pins according to the manufacturer layout guidance.
Recommandé
Sample-and-Hold Systems
MAX398ESE+ supports sample-and-hold systems by selecting among eight source signals before they reach a shared acquisition or holding circuit. Its specified 100 Ω on-resistance introduces a loading term that must be included in the source-impedance design, while channel matching within 6 Ω reduces source-dependent amplitude error. The 8:1 organization saves board area compared with eight discrete paths and is especially useful in compact measurement equipment. The 3 V to 15 V supply range permits operation from compact analog rails, and the -40°C to +85°C rating provides flexibility in industrial and military-oriented equipment. Validate settling time, charge injection, leakage, off isolation, and the holding capacitor’s acquisition requirements in the final signal chain.
Recommandé
Battery-Powered Measurement Systems
The MAX398ESE+ is appropriate for battery-powered instrumentation that needs to monitor several analog sources without purchasing a separate switch for every channel. Consolidating eight inputs into one common output reduces routing complexity and can simplify the analog front end, while the 3 V minimum supply voltage supports low-voltage portable systems. The -40°C to +85°C rating is useful where equipment operates outside the typical commercial-temperature band. Battery applications should use low-leakage surrounding components and evaluate the mux’s power consumption, off leakage, and injected charge because these effects can influence battery life and measurement accuracy. Confirm that no multiplexed signal exceeds the allowed analog input range and that the selected common output can drive the downstream amplifier without excessive loading.
Recommandé
Communication and Guidance Systems
MAX398ESE+ can select control, feedback, or auxiliary analog channels in communication and guidance systems that require a compact, precision routing element. The 8:1 topology centralizes analog selection and helps maintain consistent signal conditioning across multiple sources, while its 6 Ω maximum channel matching limits variations caused by the selected path. Its 3 V to 15 V supply range supports embedded system rails and its -40°C to +85°C range covers extended-temperature equipment. In these systems, the mux must not degrade loop gain, sensing accuracy, or isolation. Check off-state leakage, channel isolation, switching transients, and common-mode limits, and use a low-impedance reference connection to prevent unwanted signals from coupling into the selected path.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MAX398ESE+ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MAX398CSE+ | MAX399ESE+ | DG408 | DG409 | DG508A | DG509A |
|---|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Function | Precision 8-channel CMOS analog multiplexer | MAX398-series precision analog multiplexer | MAX399-series analog multiplexer | Industry-standard analog multiplexer | Industry-standard analog multiplexer | Industry-standard analog multiplexer | Industry-standard analog multiplexer |
| Pin Compatibility with MAX398 | Reference device | Same MAX398 series | Pin compatible | Pin compatible | Pin compatible | Pin compatible | Pin compatible |
Principaux différenciateurs
- Broader temperature coverage (vs MAX398CSE+)
- Precision channel matching (vs DG408)
- Defined low-voltage operation (vs MAX399ESE+)
- Single-package eight-channel consolidation (vs DG508A)
Notes de conception
Treat the selected switch resistance as part of the signal path. With 100 Ω on-resistance and a source impedance of Rs, the mux and source form a divider; the approximate attenuation from a high-impedance receiver is Rs divided by Rs plus 100 Ω. Use a low source impedance or account for the attenuation during calibration. For precision measurements, verify channel matching, leakage, and injected charge because the 6 Ω matching specification does not eliminate errors from temperature, signal amplitude, or switch dynamics.
Place the bypass capacitor close to the supply pins and provide a low-impedance ground return for the reference terminals. Keep address and enable routing away from sensitive analog inputs to limit capacitive coupling from switching edges. Use a compact common-output path to the receiving amplifier or converter, and provide adequate ground-plane continuity beneath the device. The analog signal range and allowable input voltages must be checked against the manufacturer absolute maximum ratings before routing external sources.
Do not assume that a pin-compatible part is automatically a drop-in replacement. For MAX398CSE+, the principal documented difference is its 0°C to +70°C operating range compared with the -40°C to +85°C MAX398ESE+ range. For MAX399, DG408, DG409, DG508A, and DG509A, compare logic thresholds, on-resistance, leakage, off isolation, charge injection, switching time, supply range, absolute maximum ratings, and package details before releasing a substitution.
Estimated: when using the MAX398ESE+ with a 3 V supply, the maximum nominal input-to-output voltage drop is 3 V; the actual dissipation depends on the selected path and load. For a hypothetical 3 V input, 1.5 V output, and 10 mA through the switch, estimated dissipation is 15 mW using 3 V minus 1.5 V multiplied by 10 mA. This example excludes internal device loss and is not a datasheet maximum. Confirm actual on-resistance and supply current from the manufacturer data sheet for the operating condition.
Informations de conformité
The MAX398 product information identifies the family as production but does not state the requested environmental or material compliance details. AEC-Q100 is not applicable to this general-purpose analog multiplexer.