MC14052BD - 2:4 Analog Multiplexer, 280 Ohm | onsemi
Référence : MC14052BD ✓ ActifMC14052BD Présentation
An analog multiplexer is an analog switch matrix controlled by digital logic. It allows a microcontroller, test system, or data-acquisition circuit to reuse a limited number of converter inputs, sensor inputs, or instrumentation amplifiers across several analog signals. The address decoder accepts binary select inputs and connects the corresponding analog path, while the enable input provides a common operating control. This category belongs to the interface IC hierarchy: analog multiplexer -> analog switch -> interface IC -> semiconductor.
The MC14052BD operates from 3 V to 18 V and offers approximately 12 nV/sqrt(Hz) noise performance at frequencies of 1 kHz and above. Its 280 ohm typical on-resistance is suitable for medium-impedance analog networks rather than applications demanding sub-ohm precision resistance. Low-noise switching is particularly valuable when the mux sits close to a high-gain amplifier, where resistance-generated Johnson noise and switch leakage can affect the measurement floor.
Typical uses include multimeter and oscilloscope input selection, data-acquisition systems, battery-cell monitoring, audio routing, sensor multiplexing, and industrial control interfaces. Because the selected channel introduces on-resistance, capacitance, leakage, and settling behavior, the complete signal path should be evaluated with the source impedance and required measurement bandwidth. Place the device close to the protected analog node and use a high-impedance buffer after the common output when the source impedance is high.
For robust layouts, keep the selected signal traces short, return unused or disabled inputs to a defined potential, and place the device power pin close to a stable bypass capacitor. The enable function must be controlled so that unused analog paths cannot float above the active device supply. Although the broad supply range supports both 5 V and higher-voltage analog systems, logic thresholds should be checked against the controlling device.
This product page combines package, routing, selection, and drop-in replacement information with practical guidance for analog switching. It compares confirmed pin-compatible candidates and explains the electrical limits that should be checked before replacing a multiplexer in an existing board.
Alternatives de remplacement direct pour MC14052BD — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MC14052BD (même facteur de forme et même empreinte) — différant par Multiplexer Configuration, Noise Density, Package.
MC14052BF
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →NLV14052BDG
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MC14052BDG
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MC14052BD Spécifications
| Multiplexer Configuration | Dual 2:4 analog multiplexer/demultiplexer |
| Number of Circuits | 2 circuits |
| On-Resistance | 280 ohm |
| Supply Voltage Range | 3 V to 18 V |
| Boîtier | 16-pin SOIC |
| Nombre de broches | 16 pins |
| Type de montage | Surface mount |
| Densité de bruit | 12 nV/sqrt(Hz) at f greater than or equal to 1.0 kHz |
| Switching Function | 4-pole double-throw analog switching |
| Control Interface | Digital select and enable control |
| Pb-Free Availability | Pb-free packages are available |
| Statut RoHS | RoHS compliant |
Guide de configuration des broches du MC14052BD 16-pin soic
Configuration des broches du MC14052BD (boîtier 16-pin soic). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour MC14052BD.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MC14052BD convient pour 6 applications: Data Acquisition Channel Selection, Precision Multimeter Input Multiplexing, Sensor Signal Conditioning, Industrial Control Signal Routing, Audio and Low-Level Signal Routing, Battery Cell Monitoring.
Data Acquisition Channel Selection
The MC14052BD is appropriate for routing a group of analog inputs into a shared converter or amplifier channel when a board can benefit from a dual 2:4 arrangement. Its two independent switch sections allow two banks of four inputs to be selected under separate address combinations, conserving analog front-end resources while retaining a compact 16-pin SOIC footprint. The 280 ohm on-resistance must be included in the source-loading analysis, particularly for sensors with high output impedance. Low noise of approximately 12 nV/sqrt(Hz) at 1 kHz and above is useful near the input stage. Place the mux close to the signal sources, use short traces, and allow the selected channel to settle before acquisition.
Recommandé
Precision Multimeter Input Multiplexing
The MC14052BD can organize multiple measurement inputs in a digital multimeter or bench instrument by selecting among four signals on each of two channels. This reduces the number of dedicated analog paths reaching the measurement amplifier while retaining the logic control needed for range and source selection. Its approximately 12 nV/sqrt(Hz) low-noise characteristic is valuable when the selected source feeds a high-gain amplifier. The 280 ohm on-resistance can create input loading and channel-settling effects, so source impedance, protection-network capacitance, and required measurement bandwidth should be evaluated together. A buffered output may be preferable when driving a high-impedance precision amplifier.
Recommandé
Sensor Signal Conditioning
The MC14052BD can route temperature, pressure, strain, or resistance-based sensor outputs into a common conditioning amplifier when the system requires more analog inputs than the amplifier can accept directly. Two switch sections support a dual 2:4 organization, which can pair related sensor groups and simplify control firmware. The mux's low-noise specification helps when the selected signal is amplified immediately afterward, but the 280 ohm on-resistance may create an appreciable divider with a high-impedance sensor. Minimize trace length, keep the switching stage away from fast digital nodes, and confirm the amplifier's input bias and settling requirements. Use a dedicated buffer when source impedance is too high.
Recommandé
Industrial Control Signal Routing
The MC14052BD is useful in industrial control equipment that must route several low-frequency analog command or feedback signals through a common interface. Its 3 V to 18 V operating range supports multiple supply arrangements, and the integrated address decoding reduces the number of separate control lines required by the host controller. Because industrial environments can contain substantial electrical noise, the selected traces should remain away from switching power nodes and motor-control traces. The device can process analog or logic-level signals within its published operating limits, but the controlling logic must not exceed the device supply. Confirm operating-temperature requirements and add protection where exposed connectors allow transient or out-of-range voltages.
Recommandé
Audio and Low-Level Signal Routing
The MC14052BD can route low-level audio or control signals where a system requires two independent 2:4 selection networks rather than a single 8:1 bank. The approximately 12 nV/sqrt(Hz) noise density above 1 kHz supports low-level routing, although the 280 ohm on-resistance will interact with the load impedance and can produce level-dependent attenuation. Avoid driving the mux with very high source impedances and place a buffer after it when the next stage requires low loading. Keep the routing path short, decouple the supply locally, and isolate the analog traces from clock and high-current return paths. Verify channel-to-channel matching and settling requirements in the end application.
Recommandé
Battery Cell Monitoring
The MC14052BD can serve as an analog selection element in multi-cell battery-monitoring equipment, particularly where the design compares two groups of monitored voltages through shared conversion hardware. The dual 2:4 topology allows compact address control and reduces the analog routing component count. However, a battery-monitoring system must place the multiplexer where its 280 ohm on-resistance and leakage do not degrade measurement accuracy, and the common output must remain within the monitored voltage range or be appropriately protected. Use a high-impedance buffer after the selected node, maintain a defined reference on disabled inputs, and verify the complete cell-voltage range against the device's absolute maximum ratings.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MC14052BD — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MC14052BF | NLV14052BDG | MC14052BDG |
|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | onsemi |
| Package | SOIC-16 | SOIC-16 - same package | SOIC-16 - same package | SOIC-16 - same package |
| Multiplexer Configuration | Dual 2:4 | Dual 2:4 | Dual 2:4 | Dual 2:4 |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
Principaux différenciateurs
- Lower published on-resistance than MC14052BF (vs MC14052BF)
- Documented same-package replacement family (vs NLV14052BDG)
- Functionally aligned 16-SOIC sourcing option (vs MC14052BDG)
Notes de conception
Treat the selected analog path as a resistance-capacitance network rather than an ideal wire. The MC14052BD's 280 ohm on-resistance can attenuate a high-impedance source, while parasitic capacitance and the following amplifier can determine settling time. Place the multiplexer close to the source, keep the common output trace short, and place the first high-impedance buffer immediately after the mux. Re-measure settling with the actual source impedance, cable capacitance, and selected channel.
Route the common outputs and selected analog inputs away from clock, switching-regulator, and relay-control traces. Connect the device supply to a local bypass capacitor placed close to the power pin, with a short return path to the ground reference used by the analog network. Maintain a continuous ground reference beneath the SOIC where practical, and check unused or disabled analog inputs so they cannot float above the valid supply range.
Do not substitute the MC14052BD for an MC14051BD or other MC1405x member solely because the packages match. The MC14052BD is the dual 2:4 function, while the channel matrices differ. For an existing CD4052 board, verify the actual original device, compare the truth table and enable behavior, and review on-resistance, leakage, switching time, logic thresholds, and temperature limits before approving the substitution.
Operate the device only within its 3 V to 18 V supply range and ensure the digital select and enable signals remain within valid logic levels for that supply. Absolute maximum ratings are not operating targets. If external signals can exceed the supply, add appropriate clamping or protection, particularly when the mux selects sensor inputs, test leads, or externally accessible connectors.
Informations de conformité
The product listing identifies MC14052BD as RoHS compliant, and the datasheet states that Pb-free packages are available. No automotive qualification, REACH declaration, halogen-free statement, or conflict-minerals declaration was established.