MC1489APG - Quad RS-232 Receiver | onsemi | 14-DIP
Référence : MC1489APG ✗ Fin de vieMC1489APG Présentation
An RS-232 receiver is an interface integrated circuit that converts the voltage-domain signals used by RS-232 links into logic-level signals suitable for digital equipment. The MC1489 belongs to the broader interface IC hierarchy: RS-232 receiver, line receiver, logic interface, interface IC, and semiconductor. Its four-channel arrangement allows one package to receive four data or control signals, reducing component count in multi-channel equipment.
The confirmed features of the MC1489APG include its monolithic quad-receiver construction, EIA-232D interface application, 7.0 kΩ input resistance, 30 V input signal range, and 14-PDIP package. Each receiver is intended to handle the voltage levels associated with RS-232 rather than modern low-voltage CMOS interface signals. The receiver therefore complements an RS-232 line driver rather than replacing one.
The architecture separates receive-side thresholding from the external transmission medium. In a typical RS-232 link, the transmitter converts TTL or CMOS logic into bipolar line voltage, while the MC1489APG receives those line voltages and converts them into usable logic-level outputs. This division allows equipment to use a separate transmitter and receiver for full-duplex serial communication, with the receiver section suitable for computer, terminal, and industrial serial-interface equipment.
Typical applications include multi-channel RS-232 ports, data-terminal equipment, computer serial interfaces, industrial control links, and embedded systems that retain EIA-232D connections. In a design using the companion MC1488 line driver, the MC1489APG can receive up to four incoming signals while the MC1488 handles four outgoing signals. Cable routing and signal-return practices remain important because long unshielded RS-232 paths can pick up noise and introduce ground offsets.
When laying out a board around the MC1489APG, reserve the complete 14-pin footprint and provide a ground return path for every transmitted signal where practical. Keep input and output traces away from high-current switching nodes and analog power stages. Confirm connector pin assignments, logic polarity, and system grounding before connecting external equipment because reversing interface signals or failing to establish a common ground can damage a receiver input.
This product page combines the confirmed MC1489APG interface and package information, same-family replacement analysis, application guidance, and a parameter-by-parameter comparison. It is intended to help engineers confirm footprint compatibility and determine whether the receiver is appropriate for an RS-232 design.
Alternatives de remplacement direct pour MC1489APG — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MC1489APG (même facteur de forme et même empreinte) — différant par Mounting Type, Package, Function, Input Resistance, Input Signal Range.
MC1489NG4
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →MC1489NE4
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MC1489APG Spécifications
| Device Type | Quad RS-232 line receiver |
| Receiver Channel Count | 4 channels |
| Interface Standard | EIA-232D |
| Boîtier | 14-pin plastic dual in-line package (14-PDIP) |
| Type de montage | Through-hole dual in-line |
| Input Resistance | 7.0 kΩ |
| Input Signal Range | 30 V |
Guide de configuration des broches du MC1489APG 14-pin plastic dual in-line package (14-pdip)
Configuration des broches du MC1489APG (boîtier 14-pin plastic dual in-line package (14-pdip)). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour MC1489APG.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MC1489APG convient pour 6 applications: Legacy RS-232 Computer Port, Data-Terminal Equipment Interface, Industrial Control Serial Link, Multi-Channel Serial Test Equipment, Embedded RS-232 Communication, Instrumentation and Measurement Equipment.
Legacy RS-232 Computer Port
The MC1489APG is appropriate for receiving four incoming RS-232 signals in legacy computer and peripheral interfaces because it combines four independent receiver channels in one 14-PDIP package. According to the onsemi MC1489 datasheet, the device supports a 30 V input signal range and a 7.0 kΩ input resistance, characteristics suited to EIA-232D receive paths. It can be paired with the MC1488NE4 four-channel transmitter to create a bidirectional serial interface. During layout, place the receiver away from switching regulators and high-current digital return paths, and maintain an adequate ground reference between connected equipment.
Recommandé
Data-Terminal Equipment Interface
The MC1489APG fits data-terminal equipment that receives several control and data channels from an RS-232 host. Its monolithic quad-receiver configuration reduces the number of receiver packages required for a four-line interface, while the documented 30 V signal range addresses the bipolar voltage domain used by EIA-232D. The 14-PDIP outline is suited to through-hole industrial control boards and legacy test equipment. Validate the exact receiver thresholds and logic polarity in the manufacturer datasheet, then provide chassis or logic-ground connections according to the equipment grounding strategy.
Recommandé
Industrial Control Serial Link
The MC1489APG can be used as the receive section of a legacy industrial RS-232 control link carrying four inbound signals from an operator panel, service console, or controller. Its four integrated receivers reduce board area compared with separate single-channel devices, and its 7.0 kΩ input resistance limits input loading relative to lower-impedance designs. Use shielded or twisted-pair wiring where appropriate and route the interface away from motor-switching nodes. The selected onsemi ordering code must be checked for operating-temperature and lifecycle suitability before installation in industrial equipment.
Recommandé
Multi-Channel Serial Test Equipment
The MC1489APG is useful in legacy serial test equipment that must interrogate four RS-232 receive lines through one standardized package. The confirmed EIA-232D application, 30 V input signal range, and 7.0 kΩ input resistance provide the fundamental receive-path parameters needed for interface assessment. Because the device has four receivers rather than a complete transceiver, the transmitter function must be supplied separately. Keep test-fixture ground paths short and maintain signal segregation between adjacent connector channels to prevent crosstalk during low-level threshold measurements.
Recommandé
Embedded RS-232 Communication
The MC1489APG can provide the receive side of an embedded controller that communicates through a four-channel RS-232 interface. The monolithic receiver arrangement allows one package to recover multiple incoming modem-control or data signals while the companion MC1488NE4 handles outgoing lines. Its documented input resistance of 7.0 kΩ and input signal range of 30 V are relevant when evaluating source loading and logic thresholds. Firmware and circuitry must also account for inversion, noise margins, and the actual connector wiring, because the receiver does not perform protocol conversion.
Recommandé
Instrumentation and Measurement Equipment
The MC1489APG is applicable to measurement instruments and laboratory controllers that retain four-wire RS-232 command interfaces. The quad receiver consolidates multiple incoming control signals into a 14-pin through-hole package, while the confirmed 30 V input range accommodates the voltage amplitudes associated with EIA-232D. Place the receiver near the protected connector entry, but keep the input path away from clock, relay, and switching-power traces. Confirm protection-network ratings and equipment grounding so external cable transients do not exceed the receiver's absolute maximum conditions.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MC1489APG — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MC1489NG4 | MC1489NE4 |
|---|---|---|---|
| Package | 14-PDIP | 14-PDIP | 14-PDIP |
| Brand | onsemi | onsemi | onsemi |
| Device Function | Quad RS-232 receiver | Quad RS-232 receiver | Quad RS-232 receiver |
| Receiver Channels | 4 channels | 4 channels | 4 channels |
| Interface Standard | EIA-232D | EIA-232D | EIA-232D |
| Lifecycle Status | unknown | unknown | unknown |
Principaux différenciateurs
- Four receive channels in one 14-pin package (vs SN75189AD)
- Documented 30 V receive-signal range (vs MC1489NG4)
- Confirmed 7.0 kΩ input resistance (vs MC1489NE4)
Notes de conception
Reserve the complete 14-pin through-hole footprint and preserve clearance around the DIP body for insertion, soldering, and inspection. The confirmed package is 14-PDIP, but the board outline must still be checked against the detailed package drawing for lead pitch, row spacing, and maximum dimensions. Assign the receiver inputs directly from the protected connector side where practical so that noise-sensitive traces do not run beneath unrelated switching circuitry.
Do not treat the MC1489APG as a TTL or CMOS receiver. It is designed for the bipolar voltage domain associated with EIA-232D and has a documented 30 V input signal range. Verify receiver threshold values, logic polarity, absolute maximum input voltage, and supply requirements in the onsemi datasheet before applying external signals. Also verify that every connected system shares an appropriate ground reference, because a signal without a return path cannot be interpreted reliably.
Keep the four receive inputs away from relay contacts, high-current switching nodes, inductors, and fast digital clocks. Connect the receiver ground to the interface ground using a direct, low-impedance path, and place any approved protection components close to the external connector. This arrangement reduces the chance that cable-borne transients or internal switching noise will be coupled into the receiver inputs before the system can distinguish a valid RS-232 state.
Use a separate return conductor or suitable shield for each transmitted signal in long or electrically noisy installations, and keep the receiver inputs away from parallel runs that share substantial current paths. The documented 7.0 kΩ input resistance helps limit receiver loading, but it does not eliminate ground-offset, crosstalk, or common-mode problems. Validate long cable behavior at the actual baud rate and with the external equipment's grounding configuration connected.
Informations de conformité
The MC1489APG is a digital RS-232 interface IC rather than an automotive-qualified power device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not stated in the available component information and remain unknown.