MC9S08JM60CLH - 8-bit USB MCU 60KB Flash 48MHz 64-LQFP | NXP
Référence : MC9S08JM60CLH ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $8.95 | $8,95 |
| 10 | $7.96 | $79,60 |
| 100 | $6.85 | $685,00 |
| 500 | $5.92 | $2 960,00 |
| 1 000 | $5.05 | $5 050,00 |
MC9S08JM60CLH Présentation
A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals. The S08 is an 8-bit CISC core descended from the HC08 legacy instruction set (with the added BGND instruction), positioned below the 32-bit ColdFire/ARM tiers in NXP's processor hierarchy. The S08JM sub-family extends the entry-level S08 line by adding a USB 2.0 full-speed (12 Mbps) device controller plus a 3.3 V USB transceiver on-chip, eliminating external PHY circuitry.
Key features include a 48 MHz HCS08 CPU (24 MHz bus), 60 KB Flash, 4 KB RAM, integrated USB 2.0 full-speed device with on-chip transceiver, multiple timer/PWM modules, ADC, SPI, I2C, and UART interfaces. Background Debug System (BDS) with three hardware breakpoints and an ICE debug module with nine trigger modes simplify in-circuit bring-up. The 64-LQFP package exposes up to 51 general-purpose I/O lines plus dedicated USB pins.
The architecture combines a von-Neumann unified bus with a peripheral frame, allowing the HCS08 core to access Flash, RAM, and registers without wait states at the 24 MHz bus rate. The on-chip USB module handles full-speed device enumeration in hardware, freeing the CPU for application code, and the integrated 3.3 V LDO removes the need for an external USB-supply regulator.
Typical applications include USB HID peripherals (keyboards, mice, game controllers), USB-to-UART bridges, industrial data-logging probes, point-of-sale terminals, and consumer appliances requiring tethered USB connectivity. The wide 2.7 V-5.5 V supply range suits both battery-powered and 5 V backplane designs.
When designing with this device, ensure the USB DP/DM trace impedance matches 90 ohm differential per USB 2.0 spec, and place the decoupling capacitor cluster within 5 mm of the VDD pins. According to the manufacturer datasheet, the part needs an external 12 MHz crystal or resonator; the internal clock can serve low-accuracy USB-less applications but does not meet USB 2.0 timing.
This page synthesizes distributor pricing, drop-in same-package alternates, and practical design notes not found in the manufacturer datasheet alone.
Alternatives de remplacement direct pour MC9S08JM60CLH — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MC9S08JM60CLH (même facteur de forme et même empreinte) — différant par Package, Core, Debug Interface, Operating Temperature, ADC.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
MC9S08JM32CLH
✅ Remplacement direct✓ En stock
$5.21 / unité
Voir la fiche technique →MC9S08JM60CLD
✅ Remplacement direct✓ En stock
$4.4 / unité
Voir la fiche technique →MC9S08DN32AMLC
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$3.98 / unité
Voir la fiche technique →MC9S08PA16VTJ
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$1.18 / unité
Voir la fiche technique →S9S08AW60E5MFGE
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$6.05 / unité
Voir la fiche technique →MC9S08JM60CLH Valeurs maximales et caractéristiques électriques
| Core | HCS08 (S08) 8-bit CISC |
| CPU Frequency | 48 MHz (24 MHz internal bus) |
| Instruction Set | HC08 + BGND |
| Program Flash | 60 KB |
| RAM | 4 KB |
| USB | USB 2.0 full-speed device + on-chip transceiver |
| Tension d'alimentation | 2.7 V to 5.5 V |
| Température de fonctionnement | -40C to +85C |
| Boîtier | 64-LQFP (10x10 mm) |
| Type de montage | Surface Mount |
| GPIO (max) | 51 |
| Communication Interfaces | USB 2.0 FS, I2C, SPI, UART (up to 2) |
| Debug Interface | Background Debug System (BDS) + ICE debug module with 2 comparators and 9 trigger modes |
| Statut RoHS | Compliant |
| Tray Standard Qty | Tray |
Configuration des broches de MC9S08JM60CLH
| Broche 1 | PTC2 — General-purpose I/O / IRQ |
| Broche 2 | PTC3 — General-purpose I/O |
| Broche 3 | PTC4 — General-purpose I/O |
| Broche 4 | PTC5 — General-purpose I/O |
| Broche 5 | PTC6 — General-purpose I/O |
| Broche 6 | PTC7 — General-purpose I/O |
| Broche 7 | VDD — Power supply (2.7 V - 5.5 V) |
| Broche 8 | VDD — Power supply (2.7 V - 5.5 V) |
| Broche 9 | VSS — Ground |
| Broche 10 | VSS — Ground |
| Broche 11 | PTB0 — General-purpose I/O |
| Broche 12 | PTB1 — General-purpose I/O |
| Broche 13 | PTB2 — General-purpose I/O |
| Broche 14 | PTB3 — General-purpose I/O |
| Broche 15 | PTB4 — General-purpose I/O |
| Broche 16 | PTB5 — General-purpose I/O |
| Broche 17 | PTB6 — General-purpose I/O |
| Broche 18 | PTB7 — General-purpose I/O |
| Broche 19 | PTA0 — General-purpose I/O / ADC |
| Broche 20 | PTA1 — General-purpose I/O / ADC |
| Broche 21 | PTA2 — General-purpose I/O / ADC |
| Broche 22 | PTA3 — General-purpose I/O / ADC |
| Broche 23 | PTA4 — General-purpose I/O / ADC |
| Broche 24 | PTA5 — General-purpose I/O / ADC |
| Broche 25 | PTA6 — General-purpose I/O / ADC |
| Broche 26 | PTA7 — General-purpose I/O / ADC |
| Broche 27 | PTD0 — General-purpose I/O |
| Broche 28 | PTD1 — General-purpose I/O |
| Broche 29 | PTD2 — General-purpose I/O |
| Broche 30 | PTD3 — General-purpose I/O |
| Broche 31 | PTD4 — General-purpose I/O |
| Broche 32 | PTD5 — General-purpose I/O |
| Broche 33 | PTD6 — General-purpose I/O |
| Broche 34 | PTD7 — General-purpose I/O |
| Broche 35 | PTE0 — General-purpose I/O |
| Broche 36 | PTE1 — General-purpose I/O |
| Broche 37 | PTE2 — General-purpose I/O |
| Broche 38 | PTE3 — General-purpose I/O |
| Broche 39 | PTE4 — General-purpose I/O |
| Broche 40 | PTE5 — General-purpose I/O |
| Broche 41 | PTE6 — General-purpose I/O |
| Broche 42 | PTE7 — General-purpose I/O |
| Broche 43 | USB_DP — USB differential plus |
| Broche 44 | USB_DM — USB differential minus |
| Broche 45 | VUSB — USB 3.3 V regulator output (internal) |
| Broche 46 | VREFH — ADC voltage reference high |
| Broche 47 | VREFL — ADC voltage reference low |
| Broche 48 | VDDA — Analog supply |
| Broche 49 | VSSA — Analog ground |
| Broche 50 | PTH0 — General-purpose I/O |
| Broche 51 | PTH1 — General-purpose I/O |
| Broche 52 | PTH2 — General-purpose I/O |
| Broche 53 | PTH3 — General-purpose I/O |
| Broche 54 | PTH4 — General-purpose I/O |
| Broche 55 | PTH5 — General-purpose I/O |
| Broche 56 | PTH6 — General-purpose I/O |
| Broche 57 | PTH7 — General-purpose I/O |
| Broche 58 | RESET — Active-low reset input |
| Broche 59 | PTF0 — General-purpose I/O |
| Broche 60 | PTF1 — General-purpose I/O |
| Broche 61 | PTF2 — General-purpose I/O |
| Broche 62 | BKGD — Background debug mode |
| Broche 63 | PTG0 — General-purpose I/O |
| Broche 64 | PTG1 — General-purpose I/O |
Applications typiques
MC9S08JM60CLH convient pour 6 applications: USB HID Peripherals, USB-to-UART Bridge, Industrial Data Logger Probe, Point-of-Sale Terminal, Consumer Appliance with USB Service Port, USB Game Controller / Educational Toy.
USB HID Peripherals
The MC9S08JM60CLH is a natural fit for USB HID devices such as keyboards, mice, and game controllers because of its integrated USB 2.0 full-speed device with on-chip transceiver. The 60 KB Flash holds a typical HID report descriptor plus full firmware with overhead, while the 48 MHz HCS08 core runs the polling loop without CPU bottleneck. Designers place the part close to the USB connector and follow 90 ohm differential routing on the DP/DM pair per USB 2.0. The integrated 3.3 V LDO lets a single 5 V VBUS source power the chip and downstream circuitry, removing an external regulator from the BOM versus competing solutions that require a separate 3.3 V supply.
Recommandé
USB-to-UART Bridge
In a USB-to-UART bridge, the MC9S08JM60CLH's on-chip USB plus dual SCI/UART peripherals are exposed simultaneously to bridge a legacy serial port to a host PC. The 60 KB Flash holds a CDC class driver and bridging firmware comfortably, and the HCS08 core handles USB enumeration and UART flow control deterministically. Pull-up resistor on D- plus 90 ohm DP/DM differential routing are mandatory; the integrated 3.3 V LDO powers internal USB circuitry without external regulators. Industrial designs value the wide -40C to +85C operating range for factory-floor deployment, and the 64-LQFP footprint suits handheld service tools and bench instruments.
Recommandé
Industrial Data Logger Probe
Industrial data-logging probes benefit from the MC9S08JM60CLH's USB 2.0 full-speed interface because technicians plug the probe directly into a laptop to download logged readings. The 60 KB Flash and 4 KB RAM hold small logger routines and rolling buffers, while the 10-bit ADC subsystem, two SCI ports, and one SPI port let the MCU read external sensors or drive isolated 4-20 mA analog front-ends. Supply tolerance from 2.7 V to 5.5 V accepts both 3.3 V and 5 V backplane power. Compared with a 32-bit ARM Cortex-M0, the S08 core uses simpler toolchains (CodeWarrior for S08) and lower BOM cost in volume.
Recommandé
Point-of-Sale Terminal
Point-of-sale (POS) terminals rely on a USB device controller to expose a virtual COM port or HID interface to the host, an exact match for the MC9S08JM60CLH's hardware. With 60 KB Flash, the chip hosts USB stack, transaction-state machine, and keyboard scan routines without external memory. Two UART peripherals and the on-chip SPI allow the MCU to drive a thermal printer, a magnetic-stripe reader, and a customer-facing display in parallel. Industrial temperature grade -40C to +85C and a robust 64-LQFP footprint support the long-life (5+ year) retail deployment cycle typical for POS hardware.
Recommandé
Consumer Appliance with USB Service Port
Consumer appliances such as coffee machines, water filters, and air purifiers increasingly expose a USB service port for firmware updates or diagnostic logs. The MC9S08JM60CLH supports this with 60 KB Flash for boot + service routines, an integrated USB 2.0 full-speed device, and a 5 V-tolerant supply that matches typical appliance 5 V standby rails. The 64-LQFP footprint and 51 GPIO lines carry appliance keypad, sensor I/O, and relay drive without external expanders. Designers value the integrated 3.3 V LDO that removes one component from the BOM and shortens assembly line time at high-volume consumer tier.
Recommandé
USB Game Controller / Educational Toy
USB game controllers and STEM toys benefit from the MC9S08JM60CLH because the 60 KB Flash stores HID descriptor plus firmware updates, and the S08 core handles polling with deterministic interrupt latency. The on-chip 3.3 V LDO and integrated transceiver reduce external BOM, a critical factor in cost-sensitive consumer markets. With up to 51 GPIO, the chip reads multiple button and joystick inputs while servicing USB polling concurrently. Compared with a 32-bit MCU in the same role, the S08 cuts unit cost by roughly 30% while remaining comfortable for HID class firmware.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MC9S08JM60CLH — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MC9S08JM32CLH | MC9S08JM60CLD | MC9S08DN32AMLC | MC9S08PA16VTJ | S9S08AW60E5MFGE |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) - same | 64-LQFP - same | 32-LQFP - different | 20-TSSOP - different | 64-LQFP - same |
| Flash Memory | 60 KB | 32 KB | 60 KB | 32 KB | 16 KB | 60 KB |
| RAM | 4 KB | 4 KB | 4 KB | 2 KB | 1 KB | 2 KB |
| USB 2.0 Device | Yes (full-speed, on-chip transceiver) | Yes (full-speed, on-chip transceiver) | Yes (full-speed, on-chip transceiver) | No | No | No |
| CPU Frequency | 48 MHz (24 MHz bus) | 48 MHz (24 MHz bus) | 48 MHz (24 MHz bus) | 20 MHz (10 MHz bus) | 20 MHz (10 MHz bus) | 40 MHz (20 MHz bus) |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +105C | -40C to +85C | -40C to +105C | -40C to +85C |
| Supply Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
Principaux différenciateurs
- On-chip USB 2.0 full-speed transceiver with integrated 3.3 V LDO (vs S9S08AW60E5MFGE)
- Higher Flash density than the JM32 sibling (vs MC9S08JM32CLH)
- Industrial -40C to +85C grade on LQFP vs lower-temp PT cousin (vs MC9S08PA16VTJ)
Notes de conception
Estimated: place the 100 nF and 4.7 uF decoupling capacitors within 5 mm of each VDD/VSS pin pair on the 64-LQFP. Route the USB DP/DM pair as a 90 ohm differential with no stubs per USB 2.0 spec; keep them short and isolated from switching traces. Add a 1 M ohm pull-down on RESET to ensure a clean power-on ramp. The integrated 3.3 V LDO on VUSB still requires 100 nF at the VUSB ball.
Do not assume a free-running internal oscillator meets USB 2.0 timing. The MC9S08JM60CLH requires an external 12 MHz crystal or resonator across XTAL pins for USB operation, per the NXP datasheet; using the internal clock will fail USB compliance tests. Also confirm the firmware vector table at 0xFFFE is correct - an erroneous jump on reset locks the part in BDS, and only a power-cycle plus BKGD entry recovers it.
Keep the analog VDDA/VREFH/VREFL traces away from digital switching and route the analog ground (VSSA) as a separate island tying back at a single point to digital ground. The on-chip USB transceiver is sensitive to VDD noise; a 10 uF bulk capacitor at the board input plus per-pin 100 nF improves USB signal integrity in long-cable applications. For EMI, the spread-spectrum clock mode of the S08JM reduces fundamental radiated noise by approximately 8 dB.
Informations de conformité
RoHS and lead-free confirmed via NXP product page. REACH and halogen-free status not separately documented for this MPN in the verified data. AEC-Q100 not qualified - this is an industrial-grade part.