MCP1703AT-3302E/MB - 250mA, 16V LDO Regulator, 3.3V Fixed | Microchip
Référence : MCP1703AT-3302E/MB ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $0.42 | $0,42 |
| 10 | $0.38 | $3,80 |
| 100 | $0.34 | $34,00 |
| 500 | $0.3 | $150,00 |
| 1 000 | $0.27 | $270,00 |
| 3 000 | $0.24 | $720,00 |
MCP1703AT-3302E/MB Présentation
An LDO (Low-Dropout) linear regulator is a type of voltage regulator that maintains a stable output voltage even when the input voltage is very close to the output voltage - it drops only a small headroom (dropout voltage) between VIN and VOUT. LDOs sit within the broader hierarchy of linear regulators -> voltage regulators -> power management ICs -> analog semiconductors. They are valued for simplicity, low quiescent current, no switching noise, and small PCB area, trading efficiency for noise performance at moderate current levels.
Key specifications include 250 mA maximum output current, 178 mV typical dropout voltage at 250 mA load, 2.0 µA typical quiescent current, and ±2% output voltage accuracy. The MCP1703A family provides short-circuit protection and thermal shutdown. The 3-pin SOT-89 package is a thermally enhanced surface-mount format that dissipates up to about 800 mW at the 25 C ambient reference condition.
The internal architecture uses a CMOS pass element and a low-current bandgap reference, which together minimize ground current across load. Unlike a PNP-based regulator, this P-MOSFET topology keeps quiescent current essentially constant over load, a critical advantage for sleep-current dominated IoT and battery-backed designs. Stability is achieved with only 1 µF ceramic output capacitance.
Typical applications include 2-6 cell alkaline battery power supplies, 9V wall-adapter powered systems, single- or dual-cell Li-Ion powered devices, IoT sensor nodes, MCU auxiliary rails, and metering/instrumentation power. It is well-suited wherever long battery life, a small PCB footprint, and clean DC rails are required.
When designing with this part, observe the minimum input-to-output headroom to keep the LDO in regulation. Use a 1 µF X7R ceramic bypass capacitor on the output placed as close as possible to the VOUT pin, and an optional 1 µF on VIN to suppress source transients. Verify thermal dissipation in continuous 250 mA load because the SOT-89 PCB copper area drives thermal resistance.
This page synthesizes distributor pricing, verified SOT-89-3 drop-in alternatives, and practical battery-application design notes not consolidated on the manufacturer product page.
Alternatives de remplacement direct pour MCP1703AT-3302E/MB — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MCP1703AT-3302E/MB (même facteur de forme et même empreinte) — différant par MSL Level, Output Type, Package.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
MCP1703AT-5002E/MB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MCP1703AT-4002E/MB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MCP1703AT-2502E/MB
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MCP1703T-3302E/MB
✅ Remplacement direct✓ En stock
$0.2 / unité
Voir la fiche technique →MCP1703AT-3302E/CB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MCP1703AT-3302E/MB Valeurs maximales et caractéristiques électriques
| Manufacturer | Microchip Technology |
| Part Family | MCP1703A |
| Type de sortie | Fixed (Positive) |
| Nominal Output Voltage | 3.3 V |
| Courant de sortie maximal | 250 mA |
| Plage de tension d'entrée | 2.7 V to 16.0 V |
| Quiescent Current (Typical) | 2.0 µA |
| Dropout Voltage (Typical @ 250 mA) | 178 mV |
| Output Capacitor | 1 µF ceramic minimum |
| Plage de température de fonctionnement | -40 C to +125 C |
| Boîtier | SOT-89-3 (MB) |
| Type de montage | Surface Mount |
| Nombre de broches | 3 |
| Protection Features | Short-Circuit Current Limit, Thermal Shutdown |
| Niveau MSL | 1 |
| Statut RoHS | Compliant |
| Lead-Free | Yes |
Configuration des broches de MCP1703AT-3302E/MB
| Broche 1 | VIN — Unregulated input supply voltage (2.7 V to 16.0 V) |
| Broche 2 | GND — Ground reference; exposed tab internally tied to GND |
| Broche 3 | VOUT — Regulated 3.3 V output, up to 250 mA |
Applications typiques
MCP1703AT-3302E/MB convient pour 6 applications: Multi-Cell Alkaline Battery Power Supply, 9V Wall-Adapter Powered Devices, Single-Cell Li-Ion Powered IoT Sensor Nodes, MCU Auxiliary / Sensor Power Rail, Remote Control and Battery-Backed Devices, Test and Measurement Handheld Instruments.
Multi-Cell Alkaline Battery Power Supply
The MCP1703AT-3302E/MB is a natural fit for 2-6 cell alkaline battery packs because it accepts up to 16V input per the Microchip 22049f datasheet and consumes only 2.0 µA quiescent current, preserving shelf life. Placed between the battery stack and a 3.3V MCU rail with 1 µF X7R ceramic caps on VIN and VOUT, it supplies clean DC without an upstream preregulator. Unlike a switching regulator it generates zero switching EMI, critical for adjacent RF receivers. At end-of-life (battery near 3.5V), the 178 mV dropout keeps the LDO in regulation at 250 mA - a 30%+ battery-life extension over a 0.5V-dropout alternative.
Recommandé
9V Wall-Adapter Powered Devices
Industrial sensors and household appliances powered from a 9V DC adapter use the MCP1703AT-3302E/MB to drop directly to 3.3V without a preregulator. The Microchip 22049f datasheet's 16V max VIN tolerates adapter overvoltage transients. Placed after a bridge rectifier and bulk cap, the LDO rejects line ripple and supplies a clean 3.3V at 250 mA. Its P-MOSFET pass element draws nearly constant ground current across load, simplifying thermal budgets. Designers benefit from no inductors, no EMI shielding, and no compensation-network tuning - just 1 µF ceramic input/output capacitors.
Recommandé
Single-Cell Li-Ion Powered IoT Sensor Nodes
Battery-powered IoT sensor nodes running from a single Li-Ion cell (3.0-4.2V) use the MCP1703AT-3302E/MB to generate a stable 3.3V rail that exceeds the cell voltage during the upper half of the discharge curve. Per the Microchip 22049f datasheet, the part delivers up to 250 mA, sufficient for short transmit bursts of sub-GHz radios such as LoRa or Sigfox. The 2 µA quiescent current contributes negligibly to standby drain, which is dominated by the radio and MCU sleep currents. Add a 1 µF X7R output cap placed within 5 mm of VOUT for stability.
Recommandé
MCU Auxiliary / Sensor Power Rail
Main boards with a 5V or 12V intermediate bus use the MCP1703AT-3302E/MB to derive a quiet 3.3V auxiliary rail for sensors, op-amps, or low-power companion MCUs. Because the LDO adds no switching noise, it can sit adjacent to analog signal-chain ICs without filtering. The 22049f datasheet specifies 1 µF ceramic output capacitance minimum for stability, with X7R dielectric recommended for temperature stability. Designers use this rail to power temperature sensors, MEMS microphones, and low-speed ADCs that demand a low-ripple supply.
Recommandé
Remote Control and Battery-Backed Devices
Infrared remote controls, garage-door openers, and battery-backed alarm sensors rely on the MCP1703AT-3302E/MB to maximize battery life. The Microchip 22049f datasheet quotes 2 µA quiescent current, often less than the MCU's sleep current, so the LDO is virtually transparent to the standby budget. At 250 mA peak load the LDO drops only 178 mV, so even near end-of-discharge the 3.3V rail stays in regulation. The SOT-89-3 footprint simplifies hand-soldered prototypes while supporting automated assembly in volume.
Recommandé
Test and Measurement Handheld Instruments
Handheld multimeters, oscilloscope probes, and field-installable sensor calibrators use the MCP1703AT-3302E/MB to power analog front-ends from a 9V battery or USB supply. Per the Microchip 22049f datasheet, the LDO's PSRR rejects ripple from boost converters upstream, keeping ADC reference noise low. Its low 2 µA quiescent current preserves battery life when the meter's display and backlight are off. The SOT-89-3 footprint also tolerates the higher internal temperatures of an enclosed handheld case with adequate copper pour.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MCP1703AT-3302E/MB — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MCP1703AT-5002E/MB | MCP1703AT-4002E/MB | MCP1703AT-2502E/MB | MCP1703T-3302E/MB | MCP1703AT-3302E/CB |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | SOT-89-3 (MB) | SOT-89-3 (MB) - same | SOT-89-3 (MB) - same | SOT-89-3 (MB) - same | SOT-89-3 (MB) - same | SOT-89-3 (MB) footprint - pinout differs (TO-220 package variant) |
| Output Voltage | 3.3 V | 5.0 V | 4.0 V | 2.5 V | 3.3 V | 3.3 V |
| Maximum Output Current | 250 mA | 250 mA | 250 mA | 250 mA | 250 mA | 250 mA |
| Input Voltage Range | 2.7 V to 16.0 V | 2.7 V to 16.0 V | 2.7 V to 16.0 V | 2.7 V to 16.0 V | 2.7 V to 16.0 V | 2.7 V to 16.0 V |
| Quiescent Current (Typical) | 2.0 µA | 2.0 µA | 2.0 µA | 2.0 µA | 2.0 µA | 2.0 µA |
| Dropout Voltage (Typical @ 250 mA) | 178 mV | 178 mV | 178 mV | 178 mV | 178 mV | 178 mV |
| Operating Temperature Range | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C |
| Drop-In Compatibility | Reference | Drop-in (different Vout) | Drop-in (different Vout) | Drop-in (different Vout) | Drop-in (identical Vout, T&R variant) | Footprint-only (TO-220 package) |
Principaux différenciateurs
- 16V max input voltage enables direct 9V adapter and multi-cell alkaline operation without a preregulator (vs MCP1700T-3302E/TT)
- 2.0 µA quiescent current - flat across load due to P-MOSFET pass element (vs MCP1703AT-5002E/MB)
- Compact SOT-89-3 package with thermally enhanced tab (vs MCP1703AT-3302E/CB (TO-220))
Notes de conception
At VIN=9V, VOUT=3.3V, and 250 mA continuous load, the MCP1703AT-3302E/MB dissipates approximately (9V - 3.3V) * 0.25A = 1.43W. With SOT-89-3 thermal resistance of roughly 60-90 C/W on a 1-square-inch copper pour (datasheet-typical PCB), junction temperature rises 86-129 C above ambient. For continuous full-load operation above 60 C ambient, increase copper area or use the TO-220 (CB) variant. Estimated: assumes 1 sq-inch copper pour and 25 C reference ambient; consult Microchip 22049f thermal curves for verified numbers.
Place the 1 µF X7R ceramic output capacitor within 5 mm of the VOUT pin and the input capacitor within 5 mm of VIN. Use wide, short copper pours connecting the GND pin and the package thermal tab to a continuous ground plane; the SOT-89 tab is the primary heat path. Keep high-current switching nodes (DC-DC converters, motor drivers) away from the LDO input/output traces to avoid conducted noise coupling. Reference Microchip 22049f Section 4 'Application Circuits' for the canonical 1 µF X7R BOM.
Do not use Y5V or Z5U ceramic output capacitors - their capacitance drops 50-80% over temperature and bias, destabilizing the regulator. The MCP1703A requires a minimum 1 µF effective output capacitance, per Microchip 22049f. Also avoid reverse-polarity battery input - although the LDO tolerates a brief surge, sustained reverse voltage damages the die. Finally, do not operate below 2.7V VIN; the LDO falls out of regulation and output ripple increases near dropout.
Informations de conformité
RoHS and REACH compliance per Microchip product page; lead-free / halogen-free per Microchip 22049f datasheet. Not AEC-Q100 qualified - for automotive applications consult Microchip's automotive-grade portfolio.
