MCP3301T-BI/MS - 13-Bit Differential SAR ADC | Microchip
Référence : MCP3301T-BI/MS ✓ ActifMCP3301T-BI/MS Présentation
An ADC converts a continuous analog voltage into a numeric code for processing, storage, or control. The MCP3301 belongs to the SAR ADC family, which compares the sampled input against an internal reference during successive conversion cycles. Its differential input architecture rejects common-mode noise and allows one signal to be measured relative to another rather than relative to ground. The result is a compact data-acquisition IC for battery-powered instruments, industrial sensors, and remote monitoring systems.
Key characteristics include 13-bit resolution, one differential input channel, a 100 kHz maximum sampling rate, and an SPI serial interface with an external clock option. The manufacturer identifies a 1.7 MHz external clock capability, while the listed frequency range of 85 kHz to 1.7 MHz reflects the supported operating modes. Low 50 nA input leakage helps preserve the accuracy of high-impedance sensor networks, while approximately 78 dB SNR supports accurate acquisition of slowly changing or moderate-bandwidth signals.
The SAR conversion architecture provides predictable sampling behavior and effective linearity without requiring the continuous internal clocking associated with delta-sigma converters. Digital results are transferred through the serial interface, reducing the number of package pins required for data transport. Because this is a single-channel converter, applications requiring simultaneous measurements need multiplexing ahead of the ADC or a multichannel converter family.
Typical uses include industrial process monitoring, battery-powered data loggers, environmental sensors, portable measurement instruments, and remote acquisition nodes. The differential input is particularly useful when the sensor output is small, noisy, or referenced to another voltage. The 8-lead MSOP footprint also supports compact analog front ends where board area is constrained.
For reliable operation, place the decoupling capacitor directly between the supply and ground pins, route analog and digital returns thoughtfully, and keep the analog input traces short and away from SPI switching edges. A stable reference source is essential because reference error directly limits absolute conversion accuracy. Confirm input range, acquisition timing, and available clock frequency against the manufacturer datasheet before finalizing signal-chain headroom and filtering.
This page combines the manufacturer product information, distributor technical listings, package details, and application-focused design guidance to support faster component selection, PCB planning, and signal-chain design for the MCP3301T-BI/MS.
Alternatives de remplacement direct pour MCP3301T-BI/MS — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MCP3301T-BI/MS (même facteur de forme et même empreinte) — différant par Converter Type, Package, Input Channels, Resolution, Input Architecture.
MCP3301-BI/MS
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MCP3301T-BI/MS Valeurs maximales et caractéristiques électriques
| Converter Type | Successive-approximation ADC |
| Résolution | 13 bit |
| Input Channels | 1 channel |
| Input Architecture | Fully differential |
| Conversion Rate | 100 kS/s |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Input Leakage Current | 50 nA typical |
| Signal-to-Noise Ratio | Approximately 78 dB |
| External Clock Frequency | 1.7 MHz maximum |
| Operating Clock Frequency Range | 85 kHz to 1.7 MHz |
| Digital Interface | SPI |
| Plage de température de fonctionnement | -40 °C to +85 °C |
| Temperature Grade | Industrial |
| Boîtier | 8-lead MSOP |
| Type de montage | Surface mount |
| Statut RoHS | Compliant |
Guide de configuration des broches du MCP3301T-BI/MS 8-lead msop
Configuration des broches du MCP3301T-BI/MS (boîtier 8-lead msop). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour MCP3301T-BI/MS.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MCP3301T-BI/MS convient pour 6 applications: Battery-Powered Sensor Interfaces, Industrial Process Monitoring, Environmental Monitoring, Portable Measurement Instruments, Remote Data Acquisition, Low-Voltage Control Systems.
Battery-Powered Sensor Interfaces
The MCP3301T-BI/MS fits battery-powered sensor nodes that require a compact measurement channel with differential input handling. Its 13-bit resolution and 100 kS/s conversion rate are more than adequate for temperature, pressure, and slow analog sensor outputs, while the listed 50 nA input leakage helps reduce errors from high source impedance. Place the converter behind the sensor's anti-alias filter, connect the differential signal to IN+ and IN-, and provide close supply bypassing. The principal trade-off is that only one input is converted at a time, so simultaneous measurements require external multiplexing.
Recommandé
Industrial Process Monitoring
The MCP3301T-BI/MS is suitable for industrial process-monitoring modules that acquire a differential sensor signal and transfer it to a controller. The fully differential input helps reject common-mode voltage present on long or noisy sensor connections, while 13-bit resolution supports measurement of process variables with useful digital granularity. Its -40 °C to +85 °C industrial temperature grade supports equipment deployed beyond room temperature. Use a stable reference, short analog routing, and suitable input protection. Confirm the 100 kS/s timing against the selected signal bandwidth rather than treating it as the required sample rate.
Recommandé
Environmental Monitoring
The MCP3301T-BI/MS can digitize outputs from environmental sensors such as humidity, gas, and light sensors when low-level differential signals must be measured reliably. The converter's 13-bit resolution and approximately 78 dB listed signal-to-noise ratio are useful for maintaining measurement integrity, while the SPI interface avoids a parallel data bus on a compact board. Keep the analog section separated from digital activity and place filtering close to the sensor. Because this converter has one channel, use an analog multiplexer when several environmental quantities must be acquired in sequence.
Recommandé
Portable Measurement Instruments
The MCP3301T-BI/MS supports portable instruments where a low-power, compact ADC is needed for a single precision analog input. Its small MSOP-8 footprint leaves board space for the sensor, signal conditioning, and display interface, while the differential input can simplify measurement around a biased sensor output. The 4.5 V to 5.5 V operating range is compatible with regulated 5 V systems. Design the input network for the required bandwidth and acquisition time, and verify that the reference remains stable as battery voltage and temperature change.
Recommandé
Remote Data Acquisition
The MCP3301T-BI/MS is appropriate for remote data-acquisition nodes that digitize one analog measurement and report it through a serial interface. Its low-power-oriented architecture, 8-lead MSOP package, and SPI communication reduce wiring and board-space requirements in distributed installations. The 100 kS/s conversion capability can capture waveforms or transients within the device's specified acquisition conditions, but communication timing and sensor bandwidth must also be considered. Use differential routing, guarded connectors where appropriate, and a local reference with low noise for repeatable measurements.
Recommandé
Low-Voltage Control Systems
The MCP3301T-BI/MS can serve as the analog measurement element in a compact embedded control system that accepts a differential sensor output and feeds a controller through SPI. The 13-bit code provides 8,192 nominal quantization levels, while the differential input supports grounded and offset sensor arrangements. Its 4.5 V to 5.5 V supply requirement calls for a regulated rail within the device's operating limits. Place bypass capacitance at the supply pins, keep SPI routing away from the input node, and include input limiting so transients cannot exceed the ratings in the manufacturer datasheet.
Recommandé
Données de référence d'ingénierie pour MCP3301T-BI/MS — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MCP3301-BI/MS |
|---|---|---|
| Package | 8-lead MSOP | 8-lead MSOP |
| Brand | Microchip Technology | Microchip Technology |
| Converter Type | SAR ADC | SAR ADC |
| Resolution | 13 bit | 13 bit |
| Input Channels | 1 fully differential channel | 1 fully differential channel |
| Maximum Conversion Rate | 100 kS/s | 100 kS/s |
| Digital Interface | SPI | SPI |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C |
Principaux différenciateurs
- Documented full-replacement same-brand option (vs MCP3301-BI/MS)
- Differential measurement in a compact package (vs MCP3301-BI/MS)
- Sampling capability for sensor and waveform nodes (vs MCP3301-BI/MS)
Notes de conception
Place the required supply-decoupling capacitor immediately between the VDD and VSS pins, with a short and low-inductance connection. Route the differential input as a compact pair to IN+ and IN-, keep it away from SPI clock and data traces, and avoid sharing a narrow return path with high-current digital switching nodes. For high-impedance sources, use guarding where practical because leakage, parasitic capacitance, and trace contamination can affect acquisition accuracy.
Do not treat the 100 kS/s conversion-rate figure as a guarantee that every input can be sampled at that rate. Confirm the selected clock mode, acquisition time, source impedance, input filter, and SPI timing in the manufacturer datasheet. A common error is omitting the acquisition interval needed to charge the internal sample-and-hold capacitor through a high-impedance sensor, which can produce level-dependent conversion errors.
Operate the MCP3301T-BI/MS only within its specified 4.5 V to 5.5 V supply range, including startup and transient conditions. Reference-voltage accuracy and noise contribute directly to absolute measurement accuracy, so use a stable reference and avoid routing the reference node near digital return currents. Confirm whether the selected reference configuration and supply arrangement require additional bypass components according to the manufacturer application guidance.
Informations de conformité
RoHS compliance is identified in the technical listing for MCP3301T-BI/MS. The component is an industrial-temperature ADC, but no AEC-Q100 qualification is indicated.