Microchip Technology

MCP3301T-BI/MS - 13-Bit Differential SAR ADC | Microchip

N.º de pieza: MCP3301T-BI/MS ✓ Activo
4.5 V to 5.5 V Vdss 50 nA typical Id 8-lead MSOP Package 1.7 MHz maximum Speed
MOQ: 1 |

MCP3301T-BI/MS Descripción general

Microchip Technology MCP3301T-BI/MS is a 13-bit successive-approximation analog-to-digital converter with one fully differential input, a 100 kHz conversion rate, and an 8-lead MSOP package. It operates from a 4.5 V to 5.5 V supply, supports an SPI interface, and is specified for industrial temperatures from -40 °C to +85 °C. The device provides a 50 nA typical input leakage current and approximately 78 dB signal-to-noise performance, making it suitable for precision analog measurement systems.

An ADC converts a continuous analog voltage into a numeric code for processing, storage, or control. The MCP3301 belongs to the SAR ADC family, which compares the sampled input against an internal reference during successive conversion cycles. Its differential input architecture rejects common-mode noise and allows one signal to be measured relative to another rather than relative to ground. The result is a compact data-acquisition IC for battery-powered instruments, industrial sensors, and remote monitoring systems.

Key characteristics include 13-bit resolution, one differential input channel, a 100 kHz maximum sampling rate, and an SPI serial interface with an external clock option. The manufacturer identifies a 1.7 MHz external clock capability, while the listed frequency range of 85 kHz to 1.7 MHz reflects the supported operating modes. Low 50 nA input leakage helps preserve the accuracy of high-impedance sensor networks, while approximately 78 dB SNR supports accurate acquisition of slowly changing or moderate-bandwidth signals.

The SAR conversion architecture provides predictable sampling behavior and effective linearity without requiring the continuous internal clocking associated with delta-sigma converters. Digital results are transferred through the serial interface, reducing the number of package pins required for data transport. Because this is a single-channel converter, applications requiring simultaneous measurements need multiplexing ahead of the ADC or a multichannel converter family.

Typical uses include industrial process monitoring, battery-powered data loggers, environmental sensors, portable measurement instruments, and remote acquisition nodes. The differential input is particularly useful when the sensor output is small, noisy, or referenced to another voltage. The 8-lead MSOP footprint also supports compact analog front ends where board area is constrained.

For reliable operation, place the decoupling capacitor directly between the supply and ground pins, route analog and digital returns thoughtfully, and keep the analog input traces short and away from SPI switching edges. A stable reference source is essential because reference error directly limits absolute conversion accuracy. Confirm input range, acquisition timing, and available clock frequency against the manufacturer datasheet before finalizing signal-chain headroom and filtering.

This page combines the manufacturer product information, distributor technical listings, package details, and application-focused design guidance to support faster component selection, PCB planning, and signal-chain design for the MCP3301T-BI/MS.

Alternativas directas para MCP3301T-BI/MS — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con MCP3301T-BI/MS (mismo factor de forma y huella) — difiere en Converter Type, Package, Input Channels, Resolution, Input Architecture.

Microchip Technology
Converter Type: Successive-approximation analog-to-digital converter (SAR ADC)
Package: 8-MSOP, 0.118 in (3.00 mm) width
Input Channels: 1 differential input channel
Microchip Technology
Converter Type: Single-channel ADC
Package: 8-pin SOIC, 150 mil
Resolution: 13 bits

MCP3301-BI/MS

✅ Sustitución directa
Microchip Technology
📦 MSOP-8
Successive-approximation analog-to-digital converter (SAR ADC) · 13 bit · 1 differential input channel · Fully differential input · 100 ksps · Single supply · 5.5 V · SPI-compatible serial interface

Consulte el precio

Ver hoja de datos →

MCP3301T-BI/MS Valores máximos y características eléctricas

Converter Type Successive-approximation ADC
Resolución 13 bit
Input Channels 1 channel
Input Architecture Fully differential
Conversion Rate 100 kS/s
Supply Voltage Range 4.5 V to 5.5 V
Input Leakage Current 50 nA typical
Signal-to-Noise Ratio Approximately 78 dB
External Clock Frequency 1.7 MHz maximum
Operating Clock Frequency Range 85 kHz to 1.7 MHz
Digital Interface SPI
Rango de temperatura de funcionamiento -40 °C to +85 °C
Temperature Grade Industrial
Encapsulado 8-lead MSOP
Tipo de montaje Surface mount
Estado RoHS Compliant

Guía de configuración de pines de MCP3301T-BI/MS 8-lead msop

Configuración de pines para MCP3301T-BI/MS (encapsulado 8-lead msop). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.

Diagrama de patillaje del encapsulado 8-lead msop para MCP3301T-BI/MS

No hay datos detallados de patillaje disponibles para MCP3301T-BI/MS.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

MCP3301T-BI/MS es adecuado para 6 aplicacións: Battery-Powered Sensor Interfaces, Industrial Process Monitoring, Environmental Monitoring, Portable Measurement Instruments, Remote Data Acquisition, Low-Voltage Control Systems.

🔋

Battery-Powered Sensor Interfaces

The MCP3301T-BI/MS fits battery-powered sensor nodes that require a compact measurement channel with differential input handling. Its 13-bit resolution and 100 kS/s conversion rate are more than adequate for temperature, pressure, and slow analog sensor outputs, while the listed 50 nA input leakage helps reduce errors from high source impedance. Place the converter behind the sensor's anti-alias filter, connect the differential signal to IN+ and IN-, and provide close supply bypassing. The principal trade-off is that only one input is converted at a time, so simultaneous measurements require external multiplexing.

🏭

Industrial Process Monitoring

The MCP3301T-BI/MS is suitable for industrial process-monitoring modules that acquire a differential sensor signal and transfer it to a controller. The fully differential input helps reject common-mode voltage present on long or noisy sensor connections, while 13-bit resolution supports measurement of process variables with useful digital granularity. Its -40 °C to +85 °C industrial temperature grade supports equipment deployed beyond room temperature. Use a stable reference, short analog routing, and suitable input protection. Confirm the 100 kS/s timing against the selected signal bandwidth rather than treating it as the required sample rate.

🧩

Environmental Monitoring

The MCP3301T-BI/MS can digitize outputs from environmental sensors such as humidity, gas, and light sensors when low-level differential signals must be measured reliably. The converter's 13-bit resolution and approximately 78 dB listed signal-to-noise ratio are useful for maintaining measurement integrity, while the SPI interface avoids a parallel data bus on a compact board. Keep the analog section separated from digital activity and place filtering close to the sensor. Because this converter has one channel, use an analog multiplexer when several environmental quantities must be acquired in sequence.

📱

Portable Measurement Instruments

The MCP3301T-BI/MS supports portable instruments where a low-power, compact ADC is needed for a single precision analog input. Its small MSOP-8 footprint leaves board space for the sensor, signal conditioning, and display interface, while the differential input can simplify measurement around a biased sensor output. The 4.5 V to 5.5 V operating range is compatible with regulated 5 V systems. Design the input network for the required bandwidth and acquisition time, and verify that the reference remains stable as battery voltage and temperature change.

🌐

Remote Data Acquisition

The MCP3301T-BI/MS is appropriate for remote data-acquisition nodes that digitize one analog measurement and report it through a serial interface. Its low-power-oriented architecture, 8-lead MSOP package, and SPI communication reduce wiring and board-space requirements in distributed installations. The 100 kS/s conversion capability can capture waveforms or transients within the device's specified acquisition conditions, but communication timing and sensor bandwidth must also be considered. Use differential routing, guarded connectors where appropriate, and a local reference with low noise for repeatable measurements.

⚡

Low-Voltage Control Systems

The MCP3301T-BI/MS can serve as the analog measurement element in a compact embedded control system that accepts a differential sensor output and feeds a controller through SPI. The 13-bit code provides 8,192 nominal quantization levels, while the differential input supports grounded and offset sensor arrangements. Its 4.5 V to 5.5 V supply requirement calls for a regulated rail within the device's operating limits. Place bypass capacitance at the supply pins, keep SPI routing away from the input node, and include input limiting so transients cannot exceed the ratings in the manufacturer datasheet.

What is the MCP3301T-BI/MS?
The MCP3301T-BI/MS is a 13-bit, single-channel, fully differential SAR analog-to-digital converter from Microchip Technology. According to the manufacturer product page, it supports an SPI interface, low power consumption, and operation from a 4.5 V to 5.5 V supply in an 8-lead MSOP package. It is intended for battery-powered systems and remote data-acquisition applications where a compact, low-noise measurement front end is required.
What is the conversion rate and resolution of MCP3301T-BI/MS?
The MCP3301T-BI/MS converts at up to 100 kS/s with 13-bit resolution. According to Microchip's MCP3301 product information and distributor specifications, the converter uses a successive-approximation architecture and provides one fully differential input. The 13-bit code corresponds to 8,192 quantization steps, while the 100 kS/s rating supports acquisition of rapidly changing inputs when sufficient acquisition and conversion timing are available.
Where can I download the MCP3301T-BI/MS datasheet PDF?
The MCP3301T-BI/MS datasheet can be located through the official Microchip MCP3301 product page at https://www.microchip.com/en-us/product/MCP3301. Select the datasheet or documentation tab for the manufacturer PDF. Use the pin-description table and electrical-characteristics section when assigning PCB tracks, selecting the reference voltage, and confirming acquisition timing for the selected SPI clock configuration.
What is the pinout of MCP3301T-BI/MS?
The MCP3301T-BI/MS uses an 8-lead MSOP package, but its complete numbered pin assignment is not reproduced on this page. Use the manufacturer datasheet's pin-configuration diagram when connecting VDD, VSS, analog inputs, reference terminals, and SPI signals. Confirm exposed-pad and thermal-layout requirements from the package drawing rather than inferring a PCB footprint from the 8-lead outline alone.
Is MCP3301T-BI/MS suitable for battery-powered data acquisition?
The MCP3301T-BI/MS is suitable for battery-powered data acquisition because the manufacturer describes the MCP3301 as a low-power ADC for battery-operated and remote systems. Its 13-bit resolution supports measurement while the 100 kS/s conversion rate is more than adequate for many sensor and logging channels. The listed 50 nA input leakage current is also favorable for high-impedance sensors because it minimizes measurement disturbance.
What is the difference between MCP3301T-BI/MS and MCP3301-BI/MS?
The MCP3301T-BI/MS and MCP3301-BI/MS are identified by cross-reference information as having consistent terminals, package characteristics, and principal performance parameters. The MCP3301T-BI/MS is specified as an 8-lead MSOP device with a 13-bit differential SAR converter and 100 kHz conversion rate. Before substitution, verify the exact ordering code, pin assignment, and acquisition requirements against each manufacturer's current datasheet.
Can MCP3301-BI/MS replace MCP3301T-BI/MS as a drop-in part?
The MCP3301-BI/MS is the closest documented same-family alternative for the MCP3301T-BI/MS, and cross-reference information describes it as a complete replacement with consistent terminals and package characteristics. Both are identified as 13-bit, 100 kHz, 8-MSOP devices. Production substitution should still follow Microchip's lifecycle and change-control process, with the exact suffix and pin configuration confirmed against current documentation.
What can replace MCP3301T-BI/MS?
The MCP3301-BI/MS is the documented drop-in candidate for the MCP3301T-BI/MS because the available cross-reference description states that the terminals and packages are consistent and that the principal functional parameters match. The search material does not establish five verified drop-in alternatives, so additional parts should not be treated as replacements without verified MSOP pin compatibility, supply range, reference input, and acquisition-timing equivalence.
What is the best equivalent to MCP3301T-BI/MS?
Among the verified candidates, MCP3301-BI/MS is the strongest same-brand drop-in equivalent for MCP3301T-BI/MS. It is listed in the same MSOP-8 format with a 13-bit, 100 kHz SAR ADC and is described as completely replaceable because its terminals and package are consistent. No cross-brand equivalent can be confirmed from the available cross-reference material, so the Microchip option is the only documented choice.
MCP3301T-BI/MS vs MCP3301-BI/MS: which is better for a new design?
Choose MCP3301T-BI/MS when its 8-lead MSOP ordering configuration matches the intended assembly and purchasing plan. Choose MCP3301-BI/MS when it provides a more suitable availability or sourcing path and the exact suffix has been validated. The documented cross-reference information indicates compatible terminals, package, and principal performance, so selection should focus on lifecycle, traceability, and current ordering-code requirements rather than basic conversion performance.
When should I choose MCP3301T-BI/MS over another single-channel ADC?
Choose MCP3301T-BI/MS when the design needs a fully differential 13-bit input, a 100 kS/s SAR conversion rate, and an SPI interface in an 8-lead MSOP package. These characteristics align with sensor interfaces, portable instruments, and remote logging nodes where input common-mode rejection and compactness matter. If a project requires simultaneous channels, higher resolution, or a different logic interface, select an ADC family designed for those requirements.
What power supply and reference considerations apply to MCP3301T-BI/MS?
The MCP3301T-BI/MS operates from a 4.5 V to 5.5 V supply, so the system rail must remain inside that range during startup, normal operation, and transients. Reference accuracy directly affects absolute conversion accuracy, so use a stable reference with suitable noise and temperature behavior. Place the required supply-decoupling capacitor close to VDD and VSS, and consult the manufacturer datasheet for the recommended reference and bypass networks.
How should MCP3301T-BI/MS be used for high-impedance sensors?
Use the MCP3301T-BI/MS with a short, guarded analog trace and a differential sensor output to minimize pickup from digital switching signals. Its listed 50 nA input leakage current is suitable for many high-impedance sensing arrangements because leakage into the source can create measurement error. Add the input filtering and acquisition time specified by the manufacturer, especially when the source impedance is large or the signal changes quickly.
What are the key specifications of MCP3301T-BI/MS that engineers should know?
The key engineering specifications are 13-bit resolution, one fully differential input, a 100 kS/s conversion rate, a 4.5 V to 5.5 V supply range, an SPI interface, 50 nA typical input leakage, and an 8-lead MSOP package. According to the manufacturer product page and distributor technical listings, the device also supports an external clock up to 1.7 MHz and is intended for low-power, remote, and battery-powered acquisition systems.
Is MCP3301T-BI/MS in stock and where can it be purchased?
Use the Request a Quote form on this page to request current availability, lead time, order quantity, and shipment options for MCP3301T-BI/MS. Stock status and fulfillment timing can change without notice, so confirm the exact 8-lead MSOP ordering code before placing an order. The form provides a direct purchasing channel without relying on potentially stale availability information.
What is the lead time for MCP3301T-BI/MS?
The current lead time for MCP3301T-BI/MS should be requested through the Request a Quote form on this page. Include the required quantity, package form, target date, and production or prototype status in the request. The component is an active catalog part according to the manufacturer product page, but manufacturing schedule and market availability should be confirmed for each order.

Datos de referencia de ingeniería para MCP3301T-BI/MS — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose MCP3301T-BI/MS when a design requires a 13-bit, single-channel, fully differential SAR ADC with a 100 kS/s conversion rate, SPI communication, and an 8-lead MSOP footprint. It is particularly suitable for compact battery-powered instruments, remote acquisition nodes, and industrial sensor interfaces where differential input handling and low 50 nA leakage are useful. Choose MCP3301-BI/MS when it offers a better lifecycle, traceability, or ordering path and its exact suffix is approved for the intended assembly. The documented cross-reference indicates compatible terminals and principal performance, but production substitution should still undergo a full datasheet, pin, reference-voltage, acquisition-time, and lifecycle review. Do not select a converter based on package size alone if the design requires multiple simultaneous channels, a different supply range, or a sampling rate beyond the documented 100 kS/s capability.

Comparación con alternativas

Parámetro Este producto MCP3301-BI/MS
Package 8-lead MSOP 8-lead MSOP
Brand Microchip Technology Microchip Technology
Converter Type SAR ADC SAR ADC
Resolution 13 bit 13 bit
Input Channels 1 fully differential channel 1 fully differential channel
Maximum Conversion Rate 100 kS/s 100 kS/s
Digital Interface SPI SPI
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C

Diferenciadores clave

  • Documented full-replacement same-brand option (frente a MCP3301-BI/MS)
  • Differential measurement in a compact package (frente a MCP3301-BI/MS)
  • Sampling capability for sensor and waveform nodes (frente a MCP3301-BI/MS)

Notas de diseño

Place the required supply-decoupling capacitor immediately between the VDD and VSS pins, with a short and low-inductance connection. Route the differential input as a compact pair to IN+ and IN-, keep it away from SPI clock and data traces, and avoid sharing a narrow return path with high-current digital switching nodes. For high-impedance sources, use guarding where practical because leakage, parasitic capacitance, and trace contamination can affect acquisition accuracy.

Do not treat the 100 kS/s conversion-rate figure as a guarantee that every input can be sampled at that rate. Confirm the selected clock mode, acquisition time, source impedance, input filter, and SPI timing in the manufacturer datasheet. A common error is omitting the acquisition interval needed to charge the internal sample-and-hold capacitor through a high-impedance sensor, which can produce level-dependent conversion errors.

Operate the MCP3301T-BI/MS only within its specified 4.5 V to 5.5 V supply range, including startup and transient conditions. Reference-voltage accuracy and noise contribute directly to absolute measurement accuracy, so use a stable reference and avoid routing the reference node near digital return currents. Confirm whether the selected reference configuration and supply arrangement require additional bypass components according to the manufacturer application guidance.

Información de cumplimiento

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

RoHS compliance is identified in the technical listing for MCP3301T-BI/MS. The component is an industrial-temperature ADC, but no AEC-Q100 qualification is indicated.

Datos verificados el: 2026-11-20 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

MCP3301T-BI/MS datasheet MCP3301T-BI/MS pinout MCP3301T-BI/MS datasheet pdf MCP3301T-BI/MS equivalent MCP3301T-BI/MS replacement MCP3301T-BI/MS cross reference MCP3301T-BI/MS vs MCP3301-BI/MS MCP3301T-BI/MS MSOP-8 footprint MCP3301T-BI/MS application circuit MCP3301T-BI/MS price MCP3301T-BI/MS stock Microchip Technology MCP3301T-BI/MS

Componentes & términos relacionados

Microchip Technology MCP3301T-BI/MS MCP3301-BI/MS MCP3301 13-bit ADC successive-approximation ADC SAR ADC analog-to-digital converter fully differential input SPI 100 kS/s 4.5 V to 5.5 V 50 nA input leakage 78 dB SNR MSOP-8 surface mount battery-powered systems remote data acquisition industrial process monitoring environmental sensors precision analog measurement RoHS reference voltage
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ