Microchip Technology

MCP6042-I/SN - Dual 600nA RRIO Op Amp | Microchip

Référence : MCP6042-I/SN ✓ Actif
1.4 V Vdss 600 nA per amplifier Id 8-SOIC, 3.90 mm width Package
MOQ : 1 |

MCP6042-I/SN Présentation

The Microchip Technology MCP6042-I/SN is a dual rail-to-rail input and output operational amplifier with a 14 kHz gain-bandwidth product, a typical operating current of 600 nA per amplifier, and an input offset voltage below 3 mV. It is packaged in an 8-pin SOIC and operates from a single supply as low as 1.4 V.

An operational amplifier, or op amp, is an analog active device that amplifies the difference between two input voltages. The MCP6042 belongs to the broader hierarchy of amplifiers, analog signal-conditioning ICs, and semiconductor components. Its rail-to-rail input stage accepts signals close to either supply rail, while its rail-to-rail output stage can swing toward both rails. These characteristics make it suitable for low-voltage battery systems, current sensing, sensor conditioning, and low-power analog acquisition.

The key operating features include less than 1 µA maximum quiescent current per amplifier, an input bias current of 1 pA, a slew rate of 0.003 V/µs, and rail-to-rail input and output operation. Low input bias current is particularly useful when the op amp interfaces with high-impedance sensors, because it minimizes measurement error. The 600 nA typical operating current also supports portable and energy-harvesting equipment where every microampere affects battery life.

The MCP6042 uses Microchip's advanced CMOS process technology to combine high open-loop gain, low bias current, and low power consumption. Its low-frequency bandwidth makes it better suited to slow sensor signals and precision current-loop applications than to high-speed signal chains. Designers should account for the 0.003 V/µs slew rate when driving larger capacitive loads or requiring rapid output transitions.

Typical applications include low-side current monitoring in battery-powered instruments, buffering resistive sensor bridges, amplifying thermistor and photodiode signals, and providing gain in low-power analog front ends. It is also appropriate for two-channel sensor systems where both amplifiers operate from the same low-voltage supply and must tolerate inputs near the supply rails.

When designing around the MCP6042-I/SN, use a low-noise bypass capacitor at the supply pin and keep the feedback network close to the device. Check stability with the intended source impedance, load capacitance, and gain setting. The device cannot be substituted for a high-speed amplifier when signal bandwidth or slew-rate requirements dominate.

This page combines manufacturer specifications, package and pinout details, lifecycle information, drop-in alternatives, and practical design guidance to support component selection and PCB implementation.

Alternatives de remplacement direct pour MCP6042-I/SN — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec MCP6042-I/SN (même facteur de forme et même empreinte) — différant par Package, Slew Rate, Input Bias Current, Number of Channels, Amplifier Type.

STMicroelectronics
Package: SOIC-8
Slew Rate: 0.45 V/µs
Input Bias Current: 250 nA (max)
Microchip Technology
Package: 8-pin SOIC (SN)
Slew Rate: 0.6 V/us (typical)
Input Bias Current: 1 pA (typical)
Texas Instruments
Package: 8-pin SOIC
Slew Rate: 2.4 V/µs
Number of Channels: 2 channels

MCP6042-E/SN

✅ Remplacement direct
📦 8-SOIC
Same dual amplifier and 8-SOIC pinout; operating temperature grade changes from -40°C to +85°C for I/SN to the extended commercial grade for E/SN.

📋 Alternative de référence (hors catalogue)

MCP6002-I/SN

✅ Remplacement direct
Microchip Technology
📦 8-SOIC
2 (dual) · 1 MHz (typical) · 0.6 V/us (typical) · 1.8 V to 6.0 V · 100 uA (typical) · 1 pA (typical) · 90 degrees (typical)

Contactez-nous pour le prix

Voir la fiche technique →

LMV358IDT

✅ Remplacement direct
STMicroelectronics
📦 8-SOIC
2 · 2.7 V to 5.5 V · 210 µA · 1.3 MHz · 0.45 V/µs · 1 mV (max) · 250 nA (max) · 0 V to VCC - 1.1 V

✗ Rupture de stock

$0.13 / unité

Voir la fiche technique →

TLV2372ID

✅ Remplacement direct
Texas Instruments
📦 8-SOIC
Dual operational amplifier · 2 channels · Yes · Yes · 3 MHz · 2.4 V/µs · 550 µA · 2.7 V

Contactez-nous pour le prix

Voir la fiche technique →

AD8542

✅ Remplacement direct
📦 8-SOIC
Dual rail-to-rail CMOS amplifier in an 8-SOIC package; bandwidth and supply-current behavior differ from the 14 kHz, 600 nA-per-amplifier MCP6042.

📋 Alternative de référence (hors catalogue)

MCP6042-I/SN Valeurs maximales et caractéristiques électriques

Amplifier Type General-purpose operational amplifier
Number of Amplifiers 2
Gain-Bandwidth Product 14 kHz
Typical Operating Current 600 nA per amplifier
Maximum Quiescent Current 1 µA per amplifier
Minimum Single-Supply Voltage 1.4 V
Input Offset Voltage Less than 3 mV
Input Bias Current 1 pA
Slew Rate 0.003 V/µs
Input Type Rail-to-rail
Type de sortie Rail-to-rail
Process Technology Advanced CMOS
Plage de température de fonctionnement -40°C to +85°C
Boîtier 8-SOIC, 3.90 mm width
Type de montage Surface mount
Shipping Format Tube or rail
Statut du cycle de vie Active

Configuration des broches de MCP6042-I/SN

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Broche 1 OUTA — Amplifier A output
Broche 2 IN-A — Amplifier A inverting input
Broche 3 IN+A — Amplifier A non-inverting input
Broche 4 V- — Negative supply or ground connection for single-supply operation
Broche 5 IN+B — Amplifier B non-inverting input
Broche 6 IN-B — Amplifier B inverting input
Broche 7 OUTB — Amplifier B output
Broche 8 V+ — Positive supply input

Applications typiques

MCP6042-I/SN convient pour 6 applications: Battery-Powered Sensor Conditioning, Low-Side Current Sensing, Thermistor and Resistive Bridge Readout, Photodiode Signal Amplification, Precision Voltage Buffering, Portable Environmental Monitoring.

🔋

Battery-Powered Sensor Conditioning

The MCP6042-I/SN fits battery-powered sensor nodes because its 600 nA typical operating current per amplifier limits supply demand while its 1 pA input bias current reduces loading on high-impedance sources. Place the amplifier in a non-inverting or differential gain stage near the sensor and power it from a single rail as low as 1.4 V. Rail-to-rail input operation accommodates signals near either supply limit, while the less-than-3-mV offset specification must be compared with the smallest signal the system must resolve. The 14 kHz gain-bandwidth product is appropriate for slow temperature, pressure, and chemical sensor signals rather than fast pulse shaping.

⚡

Low-Side Current Sensing

The MCP6042-I/SN can amplify the small voltage generated by a low-side shunt resistor in a battery-powered monitor. Its 1 pA input bias current contributes negligible error to the shunt measurement, and the rail-to-rail input stage accepts a differential signal close to ground. Use amplifier B as a voltage follower if the circuit also needs a buffered reference. Because the gain-bandwidth product is 14 kHz and the slew rate is 0.003 V/µs, the design is appropriate for relatively slow current measurements rather than high-di/dt waveforms.

🌡️

Thermistor and Resistive Bridge Readout

A resistive bridge or thermistor produces a small differential signal that benefits from the low input current of the MCP6042-I/SN. The 1 pA bias current minimizes perturbation of high-resistance sensing elements, while the dual-amplifier configuration allows one channel to amplify the bridge and the other to buffer a reference voltage. Rail-to-rail output swing maximizes usable signal span on a low-voltage supply. Keep the gain modest, for example 10 to 100 times, and verify that the 14 kHz closed-loop bandwidth satisfies the required sensor response time.

💡

Photodiode Signal Amplification

The MCP6042-I/SN is suitable for a small-area photodiode or optical receiver when the source impedance is high and the signal bandwidth is low. Its 1 pA input bias current reduces photocurrent-measurement error, and the rail-to-rail input stage supports operation from a single low-voltage supply. Use a transimpedance configuration with feedback resistance selected for the target sensitivity, then add a second channel for ambient-light or temperature compensation if required. The 0.003 V/µs slew rate and 14 kHz gain-bandwidth product limit the usable photodiode bandwidth, so high-speed optical links require a faster amplifier.

🔋

Precision Voltage Buffering

The dual MCP6042-I/SN can buffer two high-impedance voltage nodes when the source must drive a downstream ADC or comparator. Voltage-follower operation avoids adding gain-related bandwidth concerns, and the rail-to-rail output stage tracks inputs across most of the single-supply range. The low 600 nA typical operating current per amplifier is valuable in portable instrumentation, while the 1 pA bias current minimizes source loading. Check the output settling time against the acquisition interval and provide a stable bypass capacitor near pin 8 to maintain low-impedance supply behavior.

🌿

Portable Environmental Monitoring

The MCP6042-I/SN supports two-channel environmental monitoring systems that combine slow humidity, gas, or light sensing with a portable power budget. One amplifier can condition the active sensor while the other buffers a reference or drives a slow comparator. A single supply as low as 1.4 V reduces the energy required by the analog front end, and rail-to-rail operation simplifies signal conditioning around the supply rails. Design the external resistor network for low temperature drift, provide a local supply bypass capacitor, and confirm that accumulated offset error remains below the environmental measurement resolution.

What are the key specifications of MCP6042-I/SN?
The MCP6042-I/SN is a dual CMOS operational amplifier with a 14 kHz gain-bandwidth product, 600 nA typical operating current per amplifier, and less than 3 mV input offset voltage. It supports rail-to-rail input and output operation from a single supply as low as 1.4 V. According to the Microchip MCP6042 product page, the amplifier also features 1 pA typical input bias current and a 0.003 V/µs slew rate.
Where can I download the MCP6042-I/SN datasheet PDF?
The MCP6042-I/SN datasheet is available from the Microchip MCP6042 product page at https://www.microchip.com/en-us/product/MCP6042. The document describes the MCP6041/2/3/4 low-power amplifier family, including the MCP6042's dual configuration, electrical characteristics, typical application circuits, and package drawings. Use the manufacturer's document rather than a third-party transcription when designing the PCB or selecting a replacement.
Where can I find the MCP6042-I/SN pinout?
The MCP6042-I/SN uses a standard 8-pin SOIC arrangement with two complete operational amplifiers. Pins 1 through 4 form amplifier A, and pins 5 through 8 form amplifier B; pin 4 is V− and pin 8 is V+. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks, particularly because the negative supply pin on a single-supply design is normally connected to ground.
MCP6042-I/SN vs MCP6002-I/SN - which is better for a low-power sensor?
The MCP6042-I/SN is preferable when the 600 nA typical operating current and 14 kHz gain-bandwidth product are the primary requirements. The MCP6002-I/SN offers a 20 kHz gain-bandwidth product but draws more current and has different offset and noise characteristics. For a high-impedance sensor, the MCP6042's lower bias current and lower operating current can preserve measurement accuracy and battery life even when the MCP6002 provides more bandwidth.
What is the difference between MCP6042-I/SN and MCP6042-E/SN?
The MCP6042-I/SN and MCP6042-E/SN share the same MCP6042 dual-amplifier function and 8-SOIC footprint, but the temperature-grade suffix differs. The I/SN is the industrial-temperature ordering code, with an operating range of -40°C to +85°C, while the E/SN represents the extended commercial-temperature grade. Both provide rail-to-rail input and output operation in the same dual 8-SOIC package.
When should I choose MCP6042-I/SN over a higher-bandwidth op amp?
Choose the MCP6042-I/SN when the signal bandwidth is below its 14 kHz gain-bandwidth product and battery consumption is more important than slew rate. Its 600 nA typical operating current and 1 pA input bias current suit battery-powered sensor nodes and high-impedance sources. Select a faster amplifier instead when the required closed-loop bandwidth, output settling time, or capacitive-load drive exceeds this device's capabilities.
Is MCP6042-I/SN suitable for rail-to-rail input sensing?
Yes, the MCP6042-I/SN supports rail-to-rail input and output operation, allowing signals to approach either supply rail without requiring a separate mid-supply reference. This makes it useful for battery-powered systems whose sensor output rises or falls close to the operating supply. Input common-mode and output-swing limits should still be checked against the specific supply voltage and temperature.
What can replace the MCP6042-I/SN on an existing PCB?
The closest same-family replacement is the MCP6042-E/SN, which uses the same 8-SOIC dual-amplifier footprint and differs primarily in temperature grade. Cross-brand options identified for the MCP6042 include the LMV358, TLV2372, and AD8542 in compatible 8-pin packages. Before replacing the device, verify offset voltage, bias current, quiescent current, input common-mode range, output swing, stability, and the exact manufacturer pinout.
Is the MCP6042-I/SN the same as the MCP6042T-I/SN?
The MCP6042-I/SN and MCP6042T-I/SN represent the same electrical device with different orderable packaging configurations. The T suffix identifies a tape-and-reel shipping format, while the base MCP6042-I/SN ordering code can be supplied in tube or rail packaging. Confirm the required mounting format before ordering because the reel and tube versions are not interchangeable in the same assembly process.
Is MCP6042-I/SN in stock and what is the lead time?
Inventory and delivery timing vary by order quantity, packaging format, and current supply conditions. Use the Request a Quote form on this page to request a stock confirmation and current lead time for MCP6042-I/SN in the required tube or rail format. For production planning, request the committed schedule rather than relying on distributor inventory displayed at a single moment.
Where can I buy MCP6042-I/SN online?
Use the Request a Quote form on this page to request MCP6042-I/SN pricing, stock confirmation, and a committed lead time. Include the required quantity and whether the device is needed in tube or rail packaging. The manufacturer lists MCP6042 as active, so current production availability can be checked for the exact ordering code when planning a new assembly.
What is the price of MCP6042-I/SN?
Pricing for MCP6042-I/SN depends on quantity, packaging format, and current market conditions. Use the Request a Quote form on this page to obtain the current unit and volume pricing for the exact ordering code. Provide your target quantity and packaging preference so the quotation reflects the configuration that can be scheduled for your production run.
What is the best Texas Instruments equivalent for MCP6042-I/SN?
The LMV358 is a dual 8-pin amplifier identified as an MCP6042 equivalent in cross-reference listings. It is not an electrical match in every parameter, so it should not replace the MCP6042 where the 600 nA typical operating current or 1 pA input bias current is critical. Confirm input common-mode range, output swing, offset voltage, quiescent current, noise, and package pin assignments before substitution.
How much current does MCP6042-I/SN draw?
The MCP6042-I/SN draws a typical operating current of 600 nA per amplifier according to the Microchip product page. The MCP6041/2/3/4 family data specifies less than 1 µA maximum quiescent current per amplifier. Since the MCP6042 contains two amplifiers, engineers should evaluate the total device consumption and include supply leakage in battery-life calculations.
Does the MCP6042-I/SN require a dual supply?
No, the MCP6042-I/SN operates from a single supply as low as 1.4 V and is designed for rail-to-rail input and output behavior. In a single-supply circuit, connect V− to ground and bias the signal path within the input common-mode range. The input offset voltage is specified below 3 mV, which should be considered when resolving very small sensor signals near the supply rails.

Données de référence d'ingénierie pour MCP6042-I/SN — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose the MCP6042-I/SN when designing a battery-powered, low-frequency analog front end where supply current and input bias current are more important than bandwidth. Its 600 nA typical current per amplifier, 1 pA input bias current, and operation from a 1.4 V single supply suit high-impedance sensors and compact instrumentation. Select MCP6042-E/SN when the extended commercial temperature grade is required while retaining the same electrical configuration. Consider MCP6002-I/SN when the additional bandwidth of 20 kHz is useful, but recheck noise and power consumption. Use the LMV358, TLV2372, or AD8542 only after verifying speed, offset, bias current, supply current, common-mode range, output swing, stability, and exact pin assignments; they are cross-brand equivalents rather than identical replacements.

Comparaison avec les alternatives

Paramètre Ce produit MCP6042-E/SN MCP6002-I/SN LMV358 TLV2372 AD8542
Brand Microchip Technology Microchip Technology Microchip Technology Texas Instruments Texas Instruments Analog Devices
Package 8-SOIC 8-SOIC - same 8-SOIC - same 8-SOIC - same 8-SOIC - same 8-SOIC - same
Number of Amplifiers 2 2 2 2 2 2
Input and Output Operation Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output

Principaux différenciateurs

  • Lower typical operating current for battery-operated analog front ends (vs MCP6002-I/SN)
  • Extremely low input bias current for high-impedance sources (vs LMV358)
  • Single-supply operation starting at a low rail voltage (vs TLV2372)
  • Closest same-family replacement preserves electrical identity (vs MCP6042-E/SN)

Notes de conception

Decouple pin 8 with a local ceramic bypass capacitor and connect pin 4 to ground for single-supply operation. Place the bypass capacitor adjacent to the package rather than at the connector or power-entry point. The device's 600 nA typical operating current per amplifier minimizes internal supply demand, but board leakage, pull-up resistors, and sensor bias currents can dominate a low-power design. Avoid leaving unused amplifier inputs floating because bias currents can then translate into output offsets.

Do not treat the rail-to-rail input designation as permission to exceed the absolute maximum input voltage. Confirm the external signal range under the lowest and highest operating supply voltages, especially during shutdown or battery disconnect. The less-than-3-mV input offset is significant when the source signal is only a few millivolts; use offset calibration or a nulling strategy when the measurement resolution requires it. The 14 kHz gain-bandwidth product also limits closed-loop gain at higher frequencies.

Keep the two amplifier channels and their feedback resistors separate to minimize coupling and shared-impedance errors. For sensor interfaces, route the high-impedance input traces away from switching nodes, clock lines, and the supply bypass return path. Use a solid ground reference under the device, and keep the unused amplifier configured as a voltage follower tied to a defined low-impedance reference rather than allowing it to amplify noise.

The 0.003 V/µs slew rate and 14 kHz gain-bandwidth product make the MCP6042 best suited to slow signals. Check settling time against the sensor or ADC sample interval and avoid driving large capacitive loads directly. If capacitive loading is unavoidable, add an isolation resistor between the amplifier output and the load, then verify stability with the actual load and PCB parasitics rather than relying only on the open-loop response.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

Microchip lists MCP6042 as an active general-purpose operational amplifier. Confirm current RoHS, REACH, halogen-free, and conflict-minerals declarations for the selected package and shipping configuration during procurement.

Recherches associées

mcp6042 datasheet mcp6042 datasheet pdf mcp6042 pinout MCP6042-I/SN MCP6042-I/SN datasheet MCP6042-I/SN pinout MCP6042-I/SN equivalent MCP6042-I/SN replacement MCP6042 vs MCP6002 MCP6042 dual 600nA op amp MCP6042 SOIC-8 pinout MCP6042 low power sensor amplifier MCP6042-I/SN price MCP6042-I/SN stock

Composants & termes associés

Microchip Technology MCP6042 MCP6042-I/SN MCP6042-E/SN MCP6002-I/SN LMV358 TLV2372 AD8542 operational amplifier dual amplifier rail-to-rail input rail-to-rail output low-dropout voltage regulator CMOS gain-bandwidth product input bias current input offset voltage quiescent current slew rate SOIC-8 surface-mount package single-supply operation current sensing sensor conditioning
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ