MCP6042-I/SN - Dual 600nA RRIO Op Amp | Microchip
MPN: MCP6042-I/SN ✓ פעילMCP6042-I/SN סקירה
An operational amplifier, or op amp, is an analog active device that amplifies the difference between two input voltages. The MCP6042 belongs to the broader hierarchy of amplifiers, analog signal-conditioning ICs, and semiconductor components. Its rail-to-rail input stage accepts signals close to either supply rail, while its rail-to-rail output stage can swing toward both rails. These characteristics make it suitable for low-voltage battery systems, current sensing, sensor conditioning, and low-power analog acquisition.
The key operating features include less than 1 µA maximum quiescent current per amplifier, an input bias current of 1 pA, a slew rate of 0.003 V/µs, and rail-to-rail input and output operation. Low input bias current is particularly useful when the op amp interfaces with high-impedance sensors, because it minimizes measurement error. The 600 nA typical operating current also supports portable and energy-harvesting equipment where every microampere affects battery life.
The MCP6042 uses Microchip's advanced CMOS process technology to combine high open-loop gain, low bias current, and low power consumption. Its low-frequency bandwidth makes it better suited to slow sensor signals and precision current-loop applications than to high-speed signal chains. Designers should account for the 0.003 V/µs slew rate when driving larger capacitive loads or requiring rapid output transitions.
Typical applications include low-side current monitoring in battery-powered instruments, buffering resistive sensor bridges, amplifying thermistor and photodiode signals, and providing gain in low-power analog front ends. It is also appropriate for two-channel sensor systems where both amplifiers operate from the same low-voltage supply and must tolerate inputs near the supply rails.
When designing around the MCP6042-I/SN, use a low-noise bypass capacitor at the supply pin and keep the feedback network close to the device. Check stability with the intended source impedance, load capacitance, and gain setting. The device cannot be substituted for a high-speed amplifier when signal bandwidth or slew-rate requirements dominate.
This page combines manufacturer specifications, package and pinout details, lifecycle information, drop-in alternatives, and practical design guidance to support component selection and PCB implementation.
חלופות תחליף ישיר עבור MCP6042-I/SN — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם MCP6042-I/SN (אותו גורם צורה וטביעת רגל) — שונים ב Package, Slew Rate, Input Bias Current, Number of Channels, Amplifier Type.
MCP6042-E/SN
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MCP6002-I/SN
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LMV358IDT
✅ Drop-In✗ אזל מהמלאי
$0.13 / יחידה
הצג גיליון נתונים ←TLV2372ID
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←AD8542
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MCP6042-I/SN דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | General-purpose operational amplifier |
| Number of Amplifiers | 2 |
| Gain-Bandwidth Product | 14 kHz |
| Typical Operating Current | 600 nA per amplifier |
| Maximum Quiescent Current | 1 µA per amplifier |
| Minimum Single-Supply Voltage | 1.4 V |
| Input Offset Voltage | Less than 3 mV |
| Input Bias Current | 1 pA |
| Slew Rate | 0.003 V/µs |
| Input Type | Rail-to-rail |
| סוג פלט | Rail-to-rail |
| Process Technology | Advanced CMOS |
| טווח טמפרטורת פעולה | -40°C to +85°C |
| מארז | 8-SOIC, 3.90 mm width |
| סוג הרכבה | Surface mount |
| Shipping Format | Tube or rail |
| סטטוס מחזור חיים | Active |
תצורת פינים של MCP6042-I/SN
| פין 1 | OUTA — Amplifier A output |
| פין 2 | IN-A — Amplifier A inverting input |
| פין 3 | IN+A — Amplifier A non-inverting input |
| פין 4 | V- — Negative supply or ground connection for single-supply operation |
| פין 5 | IN+B — Amplifier B non-inverting input |
| פין 6 | IN-B — Amplifier B inverting input |
| פין 7 | OUTB — Amplifier B output |
| פין 8 | V+ — Positive supply input |
יישומים טיפוסיים
MCP6042-I/SN מתאים עבור 6 יישוםs: Battery-Powered Sensor Conditioning, Low-Side Current Sensing, Thermistor and Resistive Bridge Readout, Photodiode Signal Amplification, Precision Voltage Buffering, Portable Environmental Monitoring.
Battery-Powered Sensor Conditioning
The MCP6042-I/SN fits battery-powered sensor nodes because its 600 nA typical operating current per amplifier limits supply demand while its 1 pA input bias current reduces loading on high-impedance sources. Place the amplifier in a non-inverting or differential gain stage near the sensor and power it from a single rail as low as 1.4 V. Rail-to-rail input operation accommodates signals near either supply limit, while the less-than-3-mV offset specification must be compared with the smallest signal the system must resolve. The 14 kHz gain-bandwidth product is appropriate for slow temperature, pressure, and chemical sensor signals rather than fast pulse shaping.
מומלץ
Low-Side Current Sensing
The MCP6042-I/SN can amplify the small voltage generated by a low-side shunt resistor in a battery-powered monitor. Its 1 pA input bias current contributes negligible error to the shunt measurement, and the rail-to-rail input stage accepts a differential signal close to ground. Use amplifier B as a voltage follower if the circuit also needs a buffered reference. Because the gain-bandwidth product is 14 kHz and the slew rate is 0.003 V/µs, the design is appropriate for relatively slow current measurements rather than high-di/dt waveforms.
מומלץ
Thermistor and Resistive Bridge Readout
A resistive bridge or thermistor produces a small differential signal that benefits from the low input current of the MCP6042-I/SN. The 1 pA bias current minimizes perturbation of high-resistance sensing elements, while the dual-amplifier configuration allows one channel to amplify the bridge and the other to buffer a reference voltage. Rail-to-rail output swing maximizes usable signal span on a low-voltage supply. Keep the gain modest, for example 10 to 100 times, and verify that the 14 kHz closed-loop bandwidth satisfies the required sensor response time.
מומלץ
Photodiode Signal Amplification
The MCP6042-I/SN is suitable for a small-area photodiode or optical receiver when the source impedance is high and the signal bandwidth is low. Its 1 pA input bias current reduces photocurrent-measurement error, and the rail-to-rail input stage supports operation from a single low-voltage supply. Use a transimpedance configuration with feedback resistance selected for the target sensitivity, then add a second channel for ambient-light or temperature compensation if required. The 0.003 V/µs slew rate and 14 kHz gain-bandwidth product limit the usable photodiode bandwidth, so high-speed optical links require a faster amplifier.
מומלץ
Precision Voltage Buffering
The dual MCP6042-I/SN can buffer two high-impedance voltage nodes when the source must drive a downstream ADC or comparator. Voltage-follower operation avoids adding gain-related bandwidth concerns, and the rail-to-rail output stage tracks inputs across most of the single-supply range. The low 600 nA typical operating current per amplifier is valuable in portable instrumentation, while the 1 pA bias current minimizes source loading. Check the output settling time against the acquisition interval and provide a stable bypass capacitor near pin 8 to maintain low-impedance supply behavior.
מומלץ
Portable Environmental Monitoring
The MCP6042-I/SN supports two-channel environmental monitoring systems that combine slow humidity, gas, or light sensing with a portable power budget. One amplifier can condition the active sensor while the other buffers a reference or drives a slow comparator. A single supply as low as 1.4 V reduces the energy required by the analog front end, and rail-to-rail operation simplifies signal conditioning around the supply rails. Design the external resistor network for low temperature drift, provide a local supply bypass capacitor, and confirm that accumulated offset error remains below the environmental measurement resolution.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור MCP6042-I/SN — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MCP6042-E/SN | MCP6002-I/SN | LMV358 | TLV2372 | AD8542 |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Texas Instruments | Texas Instruments | Analog Devices |
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same |
| Number of Amplifiers | 2 | 2 | 2 | 2 | 2 | 2 |
| Input and Output Operation | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
מבדילים עיקריים
- Lower typical operating current for battery-operated analog front ends (לעומתMCP6002-I/SN)
- Extremely low input bias current for high-impedance sources (לעומתLMV358)
- Single-supply operation starting at a low rail voltage (לעומתTLV2372)
- Closest same-family replacement preserves electrical identity (לעומתMCP6042-E/SN)
הערות תכנון
Decouple pin 8 with a local ceramic bypass capacitor and connect pin 4 to ground for single-supply operation. Place the bypass capacitor adjacent to the package rather than at the connector or power-entry point. The device's 600 nA typical operating current per amplifier minimizes internal supply demand, but board leakage, pull-up resistors, and sensor bias currents can dominate a low-power design. Avoid leaving unused amplifier inputs floating because bias currents can then translate into output offsets.
Do not treat the rail-to-rail input designation as permission to exceed the absolute maximum input voltage. Confirm the external signal range under the lowest and highest operating supply voltages, especially during shutdown or battery disconnect. The less-than-3-mV input offset is significant when the source signal is only a few millivolts; use offset calibration or a nulling strategy when the measurement resolution requires it. The 14 kHz gain-bandwidth product also limits closed-loop gain at higher frequencies.
Keep the two amplifier channels and their feedback resistors separate to minimize coupling and shared-impedance errors. For sensor interfaces, route the high-impedance input traces away from switching nodes, clock lines, and the supply bypass return path. Use a solid ground reference under the device, and keep the unused amplifier configured as a voltage follower tied to a defined low-impedance reference rather than allowing it to amplify noise.
The 0.003 V/µs slew rate and 14 kHz gain-bandwidth product make the MCP6042 best suited to slow signals. Check settling time against the sensor or ADC sample interval and avoid driving large capacitive loads directly. If capacitive loading is unavoidable, add an isolation resistor between the amplifier output and the load, then verify stability with the actual load and PCB parasitics rather than relying only on the open-loop response.
מידע על תאימות
Microchip lists MCP6042 as an active general-purpose operational amplifier. Confirm current RoHS, REACH, halogen-free, and conflict-minerals declarations for the selected package and shipping configuration during procurement.