MPX4250GP - 250kPa Vented Gauge Pressure Sensor | NXP Semiconductors
Référence : MPX4250GP ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $17.5 | $17,50 |
| 10 | $15.6 | $156,00 |
| 100 | $13.5 | $1 350,00 |
| 500 | $11.2 | $5 600,00 |
| 1 000 | $9.85 | $9 850,00 |
MPX4250GP Présentation
A vented-gauge pressure sensor is a transducer that converts an applied pressure (relative to a vented reference, typically atmosphere) into an electrical signal; the silicon die uses piezoresistive strain gauges whose resistance changes with membrane deflection. Modern integrated pressure sensors like the MPX4250GP place the strain-gauge bridge, signal amplifier, temperature-compensation network, and calibration EEPROM on a single monolithic die, eliminating the external compensation circuit required by earlier raw-bridge sensors. In a typical engine-control ECU the device sits downstream of the inlet manifold, providing one of two key inputs (the other being air temperature) to the speed-density air-mass calculation.
Key features include 0.2 V to 4.9 V ratiometric output, 18.8 mV/kPa sensitivity, 0 to 250 kPa (36.26 PSI) operating range, and integrated ASIC signal conditioning. The package is a 6-pin SIP (Single Inline Package) module with a vertical port for tube-mounting and a barbed pressure inlet.
Typical applications include automotive manifold absolute pressure (MAP) sensing, turbo boost pressure monitoring, industrial process pressure measurement, and HVAC duct pressure sensing. The wide 0-250 kPa range supports both naturally aspirated and boosted engines.
When designing with this device, ensure the 5V supply is well-regulated, decouple VCC with 100 nF ceramic close to the pin, and protect the port from water and debris ingress; the vented-gauge design requires the rear vent to remain unobstructed for accurate atmospheric reference.
Alternatives de remplacement direct pour MPX4250GP — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MPX4250GP (même facteur de forme et même empreinte) — différant par Mounting Type, Supply Voltage, Output Voltage Range, Operating Temperature, Operating Pressure Range.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
MPX4250DP
✅ Remplacement direct✓ En stock
$10.4 / unité
Voir la fiche technique →MPX4250A
✅ Remplacement direct✓ En stock
$8.95 / unité
Voir la fiche technique →MPX5500DP
✅ Remplacement direct✓ En stock
$4.86 / unité
Voir la fiche technique →MPX5010GP
✅ Remplacement direct✓ En stock
$10.85 / unité
Voir la fiche technique →MPX4115AS
✅ Remplacement direct✓ En stock
$9.95 / unité
Voir la fiche technique →MPX4250GP Valeurs maximales et caractéristiques électriques
| Manufacturer | NXP Semiconductors |
| Pressure Type | Vented Gauge |
| Operating Pressure Range | 0 kPa to 250 kPa (0 to 36.26 PSI) |
| Type de sortie | Analog, Ratiometric |
| Plage de tension de sortie | 0.2 V to 4.9 V |
| Sensitivity | 18.8 mV/kPa (nominal) |
| Tension d'alimentation | 4.85 V to 5.35 V |
| Température de fonctionnement | -40C to +125C |
| Port Size | 0.19 inch (4.93 mm) male tube / barbed |
| Boîtier | 6-SIP Module (6-pin Single Inline Package) |
| Type de montage | Through-hole SIP module |
| Compensation | On-chip temperature compensated and calibrated |
Configuration des broches de MPX4250GP
| Broche 1 | VCC — +5 V supply voltage |
| Broche 2 | VOUT — Analog ratiometric pressure output (0.2 V to 4.9 V) |
| Broche 3 | GND — Ground return |
| Broche 4 | N/C — Not connected (per datasheet) |
| Broche 5 | N/C — Not connected (per datasheet) |
| Broche 6 | N/C — Not connected (per datasheet) |
Applications typiques
MPX4250GP convient pour 6 applications: Manifold Absolute Pressure (MAP) Sensor for Engine Control, Turbo Boost Pressure Monitoring, Industrial Process Pressure Measurement, HVAC Duct Static Pressure Sensing, Portable Barometric / Altitude Data Logger, Fuel and Oil Pressure Monitoring Systems.
Manifold Absolute Pressure (MAP) Sensor for Engine Control
The MPX4250GP was designed specifically for automotive manifold absolute pressure sensing, and a 0-250 kPa vented-gauge range with 18.8 mV/kPa sensitivity maps cleanly to naturally aspirated and lightly boosted gasoline engines. The on-chip temperature compensation eliminates the thermistor network older MAP sensors required, simplifying ECU firmware by feeding the ADC a clean 0.2 V to 4.9 V signal proportional to boost. The 6-SIP barbed port mounts directly to a vacuum nipple on the intake manifold.
Recommandé
Turbo Boost Pressure Monitoring
Although rated to 250 kPa, the MPX4250GP is widely used in aftermarket turbo boost gauges up to about 15 PSI of gauge pressure, well within its full-scale range. Mounting the sensor down-stream of the turbo/intercooler lets the gauge display rapid boost transients with 18.8 mV/kPa resolution, fast enough to capture spool events. The MPX4250GP's internal vented-gauge design means no external reference hose is required, a key advantage over absolute-pressure variants in open-boost-gauge installations.
Recommandé
Industrial Process Pressure Measurement
In factory automation systems, the MPX4250GP serves as a 0-250 kPa process-pressure transducer for low-pressure gas and liquid lines - common in pneumatic control loops, water-line pressure monitoring, and HVAC duct pressure sensing. The integrated temperature compensation and calibration yield better than 1 percent accuracy across the -40 C to +125 C industrial range, suitable for PLC analog inputs without further linearization. Engineers typically pair the device with a rail-to-rail op-amp buffer and a 16-bit sigma-delta ADC for instrumentation-grade readings.
Recommandé
HVAC Duct Static Pressure Sensing
Building-automation systems often measure duct static pressure in the +/- 250 kPa range to verify filter loading and fan performance. The MPX4250GP's differential sensitivity of 18.8 mV/kPa and 5 V ratiometric supply match common HVAC controller analog inputs, while the barbed port simplifies field installation with standard pneumatic tubing. The -40 C to +125 C operating range covers rooftop and mechanical-room environments, and the integrated ASIC handles drift correction that bare-bridge sensors used to require.
Recommandé
Portable Barometric / Altitude Data Logger
Battery-powered data loggers benefit from the MPX4250GP's low supply current and single-rail 5 V operation, simplifying the power tree in field-portable instruments. The vented-gauge configuration also doubles as an altimeter or weather-station barometer - subtract the local reference pressure and the output becomes a precise altitude reading up to roughly 10 km altitude. Designers typically pair the sensor with a low-power MCU and a microSD logger; the analog output eliminates need for digital sensor drivers.
Recommandé
Fuel and Oil Pressure Monitoring Systems
Heavy-duty diesel and marine engines use pressure sensors in fuel rails and oil galleries; the MPX4250GP's 250 kPa range suits low-pressure oil circuits and low-pressure fuel systems (intake side of the lift pump). The 6-SIP package and barbed port make mechanical mounting straightforward on engine blocks, while the ratiometric output drives common panel gauges and ECU analog inputs. The -40 C to +125 C operating range covers harsh under-hood conditions including crankcase and transmission oil-pan environments.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MPX4250GP — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MPX4250DP | MPX4250A | MPX5500DP | MPX5010GP | MPX4115AS |
|---|---|---|---|---|---|---|
| Package | 6-SIP Module | 6-SIP Module - same | 6-SIP Module - same | 6-SIP Module - same | 6-SIP Module - same | 6-SIP Module - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Pressure Range | 0-250 kPa (0-36.26 PSI) | 0-250 kPa | 0-250 kPa | 0-500 kPa | 0-10 kPa | 0-115 kPa absolute |
| Sensitivity | 18.8 mV/kPa | 18.8 mV/kPa | 18.8 mV/kPa | 9.0 mV/kPa | 450 mV/kPa | 40.8 mV/kPa |
| Output Voltage Range | 0.2 V to 4.9 V | 0.2 V to 4.9 V | 0.2 V to 4.9 V | 0.2 V to 4.9 V | 0.2 V to 4.9 V | 0.2 V to 4.9 V |
| Supply Voltage | 4.85 V to 5.35 V | 4.85 V to 5.35 V | 4.85 V to 5.35 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.85 V to 5.35 V |
| Port Style | Single barbed, GP | Dual port, DP | Absolute (single port) | Dual port, DP | Single barbed, GP | Single port, AS |
| Operating Temperature | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C |
Principaux différenciateurs
- Same 250 kPa range as MPX4250DP (vs MPX4250DP)
- Higher full-scale than legacy MPX4115AS (vs MPX4115AS)
- Lower current consumption than MPX5500DP (vs MPX5500DP)
Notes de conception
The MPX4250GP's output is ratiometric to the 5 V supply, so any noise or sag on VCC translates directly into pressure-reading error. Use a low-noise regulator (LDO such as the MAX176ACPA or equivalent) rather than a switching converter for the sensor rail, and place a 100 nF ceramic decoupling capacitor directly at the sensor VCC pin. Wire the device ground to the analog ground plane to avoid digital switching noise coupling into the analog output.
Route the MPX4250GP analog output trace away from high-frequency switching nodes (DC-DC inductors, MOSFET switches, microSD connectors). Keep the trace short - ideally less than 25 mm - and place a 1 kohm series resistor plus 100 pF shunt to ground at the receiving ADC input for a first-order RC anti-alias filter. Add an op-amp buffer (e.g. the MAX150ACWP+T) close to the sensor if the ADC is more than 50 mm away.
The MPX4250GP is a vented-gauge sensor and requires the rear vent port to remain unobstructed for accurate readings. Mount the device so the vent faces downward and is not blocked by sealant, condensation, or contamination. Do not apply pressures exceeding 250 kPa without consulting the overpressure rating in the datasheet - the silicon membrane can crack if the proof-pressure limit is exceeded.
The 6-SIP module sits vertically on the PCB; design the through-hole pad pattern to accept the standard 2.54 mm pin pitch of the MPXxx family. Use strain-relief on the pneumatic tube so the barbed port is not loaded axially - repeated tube-pulling can crack the plastic body. If the sensor is remote from the board, run the VCC, GND, and VOUT as a shielded twisted pair with ground on the drain wire.
Informations de conformité
Compliance status not explicitly stated in the searched snippets. AEC-Q100 qualification not explicitly stated in the verified data - automotive-grade compatibility should be confirmed with NXP directly before use in production automotive designs.
