Texas Instruments

MSP430F156IPM - 8MHz 16-Bit Mixed-Signal MCU | TI

Référence : MSP430F156IPM ✓ Actif
1.8 V to 3.6 V Vdss 330 µA at 1 MHz and 2.2 V Id 64-LQFP, 10 x 10 mm Package 8 MHz Speed 24 KB (24K x 8 plus 256 B) Memory
MOQ : 1 |

MSP430F156IPM Présentation

Texas Instruments MSP430F156IPM is an 8 MHz, 16-bit mixed-signal microcontroller with 24 KB of Flash memory, 1 KB of SRAM, and a 64-LQFP 10 x 10 mm package. The device integrates a 12-bit ADC, dual 12-bit DACs, a comparator, and a three-channel internal DMA controller for compact embedded measurement and control systems.

A microcontroller is a programmable system-on-chip that combines a processor core, memory, peripherals, and input/output interfaces on one package. The MSP430 belongs to the mixed-signal microcontroller hierarchy, combining a 16-bit RISC processor with analog measurement and conversion functions. This integration allows one device to control digital logic while acquiring, comparing, and generating analog signals, reducing component count in instrument and sensor designs.

The MSP430 CPU provides a 125 ns instruction cycle time at 8 MHz, 16-bit registers, and constant generators that support efficient code generation. Its 24 KB Flash configuration holds programmed firmware, while 1 KB of SRAM provides working memory. A three-channel DMA controller can transfer data between memory and peripherals with reduced processor intervention, which is useful when measurements must continue at predictable rates.

The analog subsystem includes a 12-bit ADC with internal reference and sample-and-hold capability, two 12-bit DAC channels, and a comparator. Serial connectivity covers I2C, SPI, and UART. The I2C controller complies with the Philips I2C specification version 2.1, supports standard mode up to 100 kbps and fast mode up to 400 kbps, and offers 7-bit and 10-bit addressing in master and slave modes.

Low-power operation is central to the architecture. The device operates from 1.8 V to 3.6 V and provides five power-saving modes. Published figures include 330 µA active current at 1 MHz and 2.2 V, 1.1 µA in standby, and 0.2 µA in off mode with RAM retention. Wake-up from standby can occur in less than 6 µs, supporting battery-powered equipment that spends most of its operating time in a low-energy state.

Typical uses include industrial sensor controllers, portable instrumentation, low-power data loggers, actuator control, and mixed-signal products requiring local ADC, DAC, and comparator resources. Designers should select decoupling capacitors and analog reference components according to the manufacturer application guidance, validate pin multiplexing in the device pin table, and keep the 1.8 V to 3.6 V supply range within the final product's environmental limits.

This page combines the manufacturer product information, distributor availability records, interface specifications, operating characteristics, application guidance, and verified replacement analysis to support faster component selection and board-level design.

Alternatives de remplacement direct pour MSP430F156IPM — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec MSP430F156IPM (même facteur de forme et même empreinte) — différant par Package, Flash Memory, Comparator, SRAM, CPU Architecture.

Texas Instruments
Flash Memory: 32 KB (32K x 8 bits plus 256 bytes)
Comparer avec MSP430F156IPM →
Texas Instruments
Package: 64-LQFP (PM), 10x10 mm
Comparator: Yes (integrated)
Comparer avec MSP430F156IPM →
Texas Instruments
Package: 64-pin LQFP (PM), 10 x 10 mm
Flash Memory: 48 KB
SRAM: 2 KB
Comparer avec MSP430F156IPM →
Texas Instruments
Package: 64-LQFP (PM), 10x10 mm
Comparer avec MSP430F156IPM →
Texas Instruments
Flash Memory: 16 KB
Comparator: 1 integrated comparator
SRAM: 512 B
Comparer avec MSP430F156IPM →
Texas Instruments
Package: 64-LQFP (PM), 10 mm x 10 mm
Flash Memory: 32 KB
Comparator: 1 comparator
Comparer avec MSP430F156IPM →
Texas Instruments
Package: 64-LQFP (10 x 10 mm)
Flash Memory: 48 KB
SRAM: 2 KB
Comparer avec MSP430F156IPM →

MSP430F149IPM

✅ Remplacement direct
Texas Instruments
📦 64-LQFP (10 x 10 mm)
MSP430 CPU16 (16-bit RISC) · MSP430x1xx · 8 MHz · 60 KB Flash (60K x 8 + 256B info) · 2 KB · 1.8 V to 3.6 V · 280 µA · 1.6 µA

Contactez-nous pour le prix

Voir la fiche technique →

MSP430F156IPM Valeurs maximales et caractéristiques électriques

Product Type 16-bit mixed-signal microcontroller
CPU Architecture 16-bit RISC
Maximum Clock Speed 8 MHz
Instruction Cycle Time 125 ns
Flash Memory 24 KB (24K x 8 plus 256 B)
SRAM 1 KB
ADC Resolution 12 bit
DAC Configuration Dual 12-bit DAC
Comparator Integrated
DMA Controller 3-channel internal DMA
Serial Interfaces I2C, SPI, and UART
I2C Maximum Data Rate 400 kbps
Supply Voltage Range 1.8 V to 3.6 V
Active Current 330 µA at 1 MHz and 2.2 V
Standby Current 1.1 µA
Off Current with RAM Retention 0.2 µA
Wake-Up Time from Standby Less than 6 µs
Power-Saving Modes 5
I/O Port Count 22
Boîtier 64-LQFP, 10 x 10 mm
Type de montage Surface mount
Operating Temperature Grade Industrial

Guide de configuration des broches du MSP430F156IPM 64-lqfp, 10 x 10 mm

Configuration des broches du MSP430F156IPM (boîtier 64-lqfp, 10 x 10 mm). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.

Schéma de brochage du boîtier 64-lqfp, 10 x 10 mm pour le MSP430F156IPM

Aucune donnée de brochage détaillée disponible pour MSP430F156IPM.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

MSP430F156IPM convient pour 6 applications: Portable Sensor Instrumentation, Industrial Sensor Control, Battery-Powered Data Logger, Precision Analog Signal Generation, Actuator and Motor Interface Control, Embedded Communication Gateway.

📱

Portable Sensor Instrumentation

The MSP430F156IPM fits portable measurement instruments that must acquire analog signals while conserving battery charge. Its 12-bit ADC, internal reference, sample-and-hold function, and three-channel DMA provide a compact path from sensor input to processed data. The 8 MHz 16-bit RISC CPU offers 125 ns instruction cycles, while five power-saving modes support designs that spend most of their time at 1.1 µA in standby. Wake-up in less than 6 µs helps the instrument respond quickly to operator input or scheduled sampling events without maintaining a continuously active processor.

🏭

Industrial Sensor Control

The MSP430F156IPM is suitable for industrial sensor-control modules that combine measurement, local decision-making, and actuator communication. The 12-bit ADC supports analog sensor conditioning, the comparator can handle threshold events, and the dual 12-bit DACs can generate control or reference voltages. Its I2C interface operates up to 400 kbps, while SPI and UART provide additional paths to sensors, converters, and remote communications. Operation from 1.8 V to 3.6 V supports low-voltage industrial designs, provided the board uses appropriate protection and decoupling.

🔧

Battery-Powered Data Logger

The MSP430F156IPM supports battery-powered data loggers that periodically sample analog channels and store or transmit results. Its three-channel DMA can move ADC data with limited processor intervention, while the 24 KB of Flash provides space for firmware and compact data structures. The 330 µA active current at 1 MHz and 2.2 V offers a defined basis for duty-cycle calculations, and the 0.2 µA off-mode current with RAM retention helps preserve operating state between measurement intervals. Storage endurance and sleep-mode current should be evaluated for each selected memory technology and sampling interval.

🎧

Precision Analog Signal Generation

The MSP430F156IPM is appropriate for compact analog-output equipment that needs accurate digital-to-analog conversion alongside embedded control. Two 12-bit DAC channels can generate reference or control voltages without requiring a separate DAC package, while the ADC provides a feedback path for monitoring the result. The 8 MHz RISC CPU can execute compensation and control algorithms with a 125 ns instruction cycle time. Designers should treat DAC output noise, reference stability, settling behavior, and output loading as board-level considerations and follow the manufacturer layout guidance for sensitive analog signals.

⚡

Actuator and Motor Interface Control

The MSP430F156IPM can serve as the supervisory controller in actuator, valve, or motor-control systems where local logic must coordinate sensors and drive signals. The comparator supports fast threshold monitoring, the ADC captures slower feedback values, and the dual DACs can provide control references. UART and SPI permit connection to gate drivers, position sensors, or communications modules, while I2C supports lower-speed peripherals. The MCU's 1.8 V to 3.6 V range integrates readily with low-voltage logic, although motor transients require separate protection and careful grounding.

🌐

Embedded Communication Gateway

The MSP430F156IPM can act as a small embedded gateway between sensors and a higher-level communications link. I2C supports standard mode through 100 kbps and fast mode through 400 kbps with 7-bit or 10-bit addressing, making it suitable for multiple slow peripherals. SPI offers higher-throughput connectivity for radio or storage devices, and UART handles simple host or module links. Five power-saving modes reduce idle consumption, while DMA can service transfers and reduce processor overhead. Production firmware must validate bus timing, interrupt priorities, and peripheral pin multiplexing for the selected board configuration.

What is the MSP430F156IPM?
The MSP430F156IPM is an active, 8 MHz, 16-bit mixed-signal microcontroller from Texas Instruments. It combines 24 KB of Flash, 1 KB of SRAM, a 12-bit ADC, two 12-bit DACs, a comparator, and a three-channel DMA controller in a 64-LQFP 10 x 10 mm package. According to the manufacturer product page and datasheet, the device also provides I2C, SPI, UART, and five power-saving modes.
What are the key specifications of MSP430F156IPM that engineers should know?
The MSP430F156IPM provides an 8 MHz clock, 125 ns instruction cycles, 24 KB of Flash, 1 KB of SRAM, and 1.8 V to 3.6 V operation. Its mixed-signal resources include a 12-bit ADC, dual 12-bit DACs, a comparator, and three-channel DMA. According to the Texas Instruments datasheet, I2C supports standard mode through 100 kbps and fast mode through 400 kbps.
Where can I download the MSP430F156IPM datasheet PDF?
The MSP430F156IPM datasheet is available through the Texas Instruments product resources for the MSP430F156, with a direct manufacturer PDF link listed on this page. Use the manufacturer datasheet for the complete pin-description table, register definitions, timing characteristics, and recommended operating circuit. The product page also provides ordering information, quality documentation, and device support resources for the MSP430F156 family.
Where can I find the MSP430F156IPM pinout?
Use the pin-description table in the Texas Instruments MSP430F156 manufacturer datasheet to assign PCB tracks and select the correct port functions. The verified ordering information identifies the MSP430F156IPM as a 64-pin LQFP in a 10 x 10 mm package. Because a complete numbered pin list is not established by the available product summaries, use the datasheet pin table as the controlling assignment for analog, communication, power, and port signals.
Is MSP430F156IPM suitable for low-power battery applications?
Yes, the MSP430F156IPM is suitable for low-power battery applications because it offers five power-saving modes and low standby and off-mode current. According to the manufacturer datasheet, typical figures include 1.1 µA in standby and 0.2 µA in off mode with RAM retention, plus wake-up from standby in less than 6 µs. Actual battery life depends on duty cycle, leakage, sensor load, and regulator efficiency.
What is the difference between MSP430F156IPM and MSP430F149IPM?
The MSP430F156IPM is optimized around 24 KB of Flash and 1 KB of SRAM, while the MSP430F149IPM belongs to the higher-memory MSP430F149 family and offers a larger memory configuration in a comparable 64-LQFP device. The manufacturer lists the MSP430F149IPM as a related comparison part. Confirm pin multiplexing, interrupt assignments, analog peripheral availability, and software device support before treating it as a drop-in replacement.
Is MSP430F156IPM the same as MSP430F149IPM?
The MSP430F156IPM and MSP430F149IPM are not identical, although they are related MSP430 devices associated with the same 64-LQFP package family. The target has 24 KB of Flash and 1 KB of SRAM, while the MSP430F149IPM provides a larger memory configuration. Firmware, peripheral availability, and pin functions must be checked in the manufacturer datasheet before substituting one for the other.
When should I choose MSP430F156IPM over another MSP430 microcontroller?
Choose the MSP430F156IPM when a design needs a compact mixed-signal MCU with an 8 MHz 16-bit CPU, 12-bit ADC, dual 12-bit DACs, comparator, DMA, and low-power operation in a 64-LQFP package. It is particularly suitable for portable measurement systems and sensor-control products. Select another family member when memory, analog-channel count, communication resources, or package pin count better matches the final design.
Can MSP430F149IPM replace MSP430F156IPM?
The MSP430F149IPM is a potential related replacement, but replacement requires software and hardware review rather than package-name matching alone. The MSP430F156IPM has 24 KB of Flash and 1 KB of SRAM, whereas the MSP430F149IPM offers a larger memory configuration. Check the manufacturer pin table, peripheral resources, clock setup, memory size, and application firmware before approving the substitution.
What is the best drop-in replacement for MSP430F156IPM?
The MSP430F149IPM is the closest verified related replacement identified for the MSP430F156IPM, with a comparable 64-LQFP format and the same Texas Instruments MSP430 family origin. It is not an exact functional equivalent because its memory configuration differs from the target's 24 KB Flash and 1 KB of SRAM. Verify pin functions, peripheral availability, voltage limits, timing, and firmware compatibility before using it as a drop-in replacement.
What is the best equivalent MSP430F149IPM replacement for MSP430F156IPM?
No cross-brand equivalent is established by the available manufacturer and distributor records. The MSP430F149IPM is the practical same-brand alternative to evaluate because it appears in a direct comparison with the MSP430F156IPM and uses a comparable 64-LQFP format. Because cross-manufacturer microcontrollers may differ in pin multiplexing, interrupt layout, analog calibration, and firmware support, they should not be treated as drop-in parts without complete design validation.
How much current does MSP430F156IPM consume?
The MSP430F156IPM consumes 330 µA in active mode at a 1 MHz clock and 2.2 V supply according to the manufacturer datasheet. Its typical standby current is 1.1 µA, while off mode with RAM retention is 0.2 µA. These operating-mode figures are more useful for battery sizing than a single maximum-current number because consumption changes with clock rate, peripherals, I/O activity, and duty cycle.
Does MSP430F156IPM support I2C, SPI, and UART?
Yes, the MSP430F156IPM supports I2C, SPI, and UART serial interfaces. According to the manufacturer datasheet, its I2C implementation follows the Philips I2C specification version 2.1, supports master and slave modes, and offers 7-bit and 10-bit addressing. Standard-mode operation is specified up to 100 kbps and fast mode up to 400 kbps, making the device suitable for sensors, converters, and external transceivers.
Is MSP430F156IPM currently active?
The MSP430F156IPM is listed with an active lifecycle status. The manufacturer product page provides ordering, quality, and support information for the MSP430F156 family, while current distributor records identify the exact MSP430F156IPM ordering code. Use the Request a Quote form on this page for current commercial availability, minimum order quantity, and delivery information.
Where can I buy MSP430F156IPM and what is its lead time?
Use the Request a Quote form on this page to request MSP430F156IPM pricing, current stock, minimum order quantity, and production lead time. The exact device is identified by distributor listings in the 64-LQFP 10 x 10 mm configuration, but availability and lead time can change with market conditions and order quantity. The manufacturer identifies the MSP430F156IPM as an active orderable configuration.

Données de référence d'ingénierie pour MSP430F156IPM — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose the MSP430F156IPM when the design needs a compact MSP430 mixed-signal controller with an 8 MHz 16-bit CPU, 12-bit ADC, dual 12-bit DACs, comparator, DMA, and low-power operation in a 64-LQFP package. Its 24 KB Flash and 1 KB SRAM are appropriate for focused firmware rather than memory-intensive applications. Evaluate the MSP430F149IPM when a related same-brand device with 60 KB Flash and 2 KB SRAM would simplify firmware growth or data buffering; its larger memory is the principal measured difference. Do not select a cross-brand replacement solely by package count. For either MSP430 option, verify the exact pin multiplexing, peripheral set, timing, voltage requirements, and software support before releasing a production design.

Comparaison avec les alternatives

Paramètre Ce produit MSP430F149IPM
Brand Texas Instruments Texas Instruments
Package 64-LQFP (10 x 10 mm) 64-LQFP (10 x 10 mm)
Maximum Clock Speed 8 MHz 8 MHz
CPU Architecture 16-bit RISC 16-bit RISC
Flash Memory 24 KB 60 KB
SRAM 1 KB 2 KB
ADC Resolution 12 bit 12 bit
Supply Voltage Range 1.8 V to 3.6 V 1.8 V to 3.6 V
Power-Saving Modes 5 5
Serial Interfaces I2C, SPI, and UART I2C, SPI, and UART

Principaux différenciateurs

  • Lower memory configuration supports firmware-cost optimization (vs MSP430F149IPM)
  • Integrated mixed-signal resources reduce external converter overhead (vs MSP430F149IPM)
  • Low-power operation supports battery-focused designs (vs MSP430F149IPM)

Notes de conception

Calculate the active duty cycle from the 330 µA figure at 1 MHz and 2.2 V, then add standby and off-mode contributions using 1.1 µA and 0.2 µA respectively. Keep the supply within 1.8 V to 3.6 V and include local bypass capacitance close to the device supply pins. Wake-up timing should be included in the response-time budget because standby wake-up can require less than 6 µs.

Separate analog and digital return currents as far as practical, maintain a compact ground reference around the ADC and DAC circuitry, and route sensitive analog inputs away from switching nodes and high-current return paths. Use the manufacturer pin-description table to verify analog, reference, communication, and port multiplexing. Validate the final layout with converter accuracy and noise measurements because package placement and grounding can materially affect mixed-signal performance.

Do not treat a shared package as proof of identical behavior. When evaluating MSP430F149IPM as a replacement, review memory size, peripheral availability, port multiplexing, interrupt assignments, clock configuration, and startup code. Also confirm the active-high or active-low polarity of every control signal in the actual schematic. A successful PCB fit alone does not establish function, timing, or firmware compatibility.

Assign I2C, SPI, and UART functions only after checking the alternate-function settings for the selected pins. I2C rise time and pull-up sizing depend on bus capacitance and speed, while SPI timing depends on the peripheral clock and trace loading. Use the manufacturer timing characteristics for setup and hold requirements and keep clock and data routing short, with a continuous ground reference beneath high-speed traces.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The device is identified as an industrial-grade mixed-signal microcontroller. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not established by the available product summaries.

Données vérifiées le : 2026-11-10 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

MSP430F156IPM datasheet MSP430F156IPM specifications MSP430F156IPM pinout MSP430F156IPM datasheet pdf Texas Instruments MSP430F156IPM MSP430F156IPM equivalent MSP430F156IPM replacement MSP430F156IPM vs MSP430F149IPM MSP430F156IPM 64-LQFP footprint MSP430F156IPM application circuit MSP430F156IPM price MSP430F156IPM stock

Composants & termes associés

Texas Instruments MSP430F156IPM MSP430F156 MSP430F149IPM mixed-signal microcontroller microcontroller system-on-chip 16-bit RISC reduced instruction set computer embedded processor semiconductor 12-bit ADC analog-to-digital converter dual 12-bit DAC digital-to-analog converter comparator DMA I2C SPI UART Philips I2C specification version 2.1 64-LQFP LQFP package family surface-mount package 5 V 1.8 V to 3.6 V 330 µA 1.1 µA 0.2 µA 8 MHz 24 KB Flash 1 KB SRAM RoHS REACH
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ