MSP430F2616TPN - 16MHz Mixed-Signal MCU | Texas Instruments
Référence : MSP430F2616TPN ✓ ActifMSP430F2616TPN Présentation
A mixed-signal microcontroller combines a digital processor with analog conversion and interface peripherals. Within the semiconductor hierarchy, the MSP430F2616TPN is an ultra-low-power MCU, a 16-bit RISC controller, and a mixed-signal embedded-processing device. Its 92 KB Flash supports firmware and application code, while 4 KB of SRAM provides working memory for real-time acquisition, control, and communication tasks.
The principal features include 16 MHz maximum clock operation, a 16-bit RISC architecture, a 12-bit ADC, dual 12-bit DAC outputs, and communication interfaces covering I2C, SPI, and UART. Two USCI blocks provide hardware support for serial communications, while DMA reduces the need for CPU intervention during peripheral transfers. The hardware multiplier is useful for signal-processing and control algorithms that benefit from efficient multiplication.
The MSP430 architecture is designed around low-power embedded control. Its peripheral integration allows a system to acquire analog measurements, perform computations, generate analog outputs, and exchange data through serial interfaces without requiring separate converters. This combination is especially useful when board area, energy use, and external component count are important. The MCU supports an industrial temperature range of -40 °C to 105 °C according to the Texas Instruments part-details listing.
Typical implementations include industrial sensor acquisition, low-power instrumentation, portable measurement equipment, actuator control, and connected embedded systems. The dual DAC can support reference or control outputs, while the ADC accommodates analog sensor inputs. I2C and SPI suit short-distance peripheral connections, and UART provides a straightforward interface for programming, diagnostics, or external controllers.
A practical design must account for the 80-pin LQFP footprint, separate analog and digital supply decoupling, and careful routing around high-impedance analog inputs. Firmware should also configure the unused peripheral pins and avoid leaving unnecessary communication interfaces or converters active in low-power operating states.
This page combines the MSP430F2616TPN device configuration with package information, application guidance, interface-focused comparisons, and replacement-selection criteria. It is intended to help engineers identify whether the MSP430F2616TPN provides the required mixed-signal resources before beginning PCB and firmware development.
Alternatives de remplacement direct pour MSP430F2616TPN — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MSP430F2616TPN (même facteur de forme et même empreinte) — différant par ADC Resolution, CPU Architecture, Hardware Multiplier, Package, SRAM.
Aucune alternative de remplacement direct disponible pour ce produit.
Demander des alternativesMSP430F2616TPN Valeurs maximales et caractéristiques électriques
| CPU Architecture | 16-bit RISC |
| Fréquence d'horloge maximale | 16 MHz |
| Flash Memory | 92 KB |
| SRAM | 4 KB |
| ADC Resolution | 12 bit |
| DAC Resolution | 12 bit |
| DAC Channels | 2 channels |
| Serial Communication Interfaces | I2C, SPI, and UART |
| USCI Blocks | 2 blocks |
| Hardware Multiplier | Present |
| Direct Memory Access | Present |
| Tension d'alimentation | 2.5 V or 3.3 V |
| Température de fonctionnement | -40 °C to 105 °C |
| Boîtier | 80-pin LQFP, 12 x 12 mm |
| Terminal Count | 80 pins |
| Type de montage | Surface mount |
| Temperature Grade | Industrial |
| Statut RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
Guide de configuration des broches du MSP430F2616TPN 80-pin lqfp, 12 x 12 mm
Configuration des broches du MSP430F2616TPN (boîtier 80-pin lqfp, 12 x 12 mm). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour MSP430F2616TPN.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MSP430F2616TPN convient pour 6 applications: Industrial Sensor Acquisition, Portable Measurement Equipment, Programmable Analog Output Control, Communications Controller, Low-Power Data Logger, Actuator and Process Control.
Industrial Sensor Acquisition
The MSP430F2616TPN fits industrial sensor-acquisition systems that need both analog measurement and local control in one package. Its 12-bit ADC samples analog inputs, while the 16 MHz CPU can perform filtering, calibration, and threshold decisions before forwarding results. Four kilobytes of SRAM provides working space for acquisition buffers and control variables, and 92 KB of Flash accommodates firmware, lookup tables, and configuration data. The -40 °C to 105 °C industrial range supports equipment operating across demanding ambient conditions. Place the analog inputs near the ADC pins, use a quiet reference and local decoupling, and isolate sensitive sensor traces from switching and digital outputs to preserve measurement quality.
Recommandé
Portable Measurement Equipment
The MSP430F2616TPN is suitable for portable instruments that combine analog measurement, data processing, and low-power serial communication. Its 16-bit RISC core supports responsive control and signal calculations at clock rates up to 16 MHz, while the integrated 12-bit ADC removes the need for a separate converter in many designs. Two 12-bit DAC channels can generate test signals, excitation levels, or calibration outputs, and I2C, SPI, and UART support external sensors, storage, and host computers. Because the MCU is designed for low-power operation, firmware should use the appropriate standby or shutdown states between measurements. Power budgeting must include ADC, DAC, interface, and I/O activity rather than relying on a single nominal current figure.
Recommandé
Programmable Analog Output Control
The MSP430F2616TPN can serve as the controller in systems requiring accurate programmable analog outputs. Its two 12-bit DAC channels are useful for equipment setpoints, actuator commands, sensor excitation, or waveform generation, while the ADC can close the loop by measuring the resulting analog condition. The 16 MHz processor provides enough control bandwidth for common feedback tasks, and the hardware multiplier supports filtering and calibration calculations. Firmware should establish a defined startup sequence for the DAC outputs so that external equipment does not receive an uncontrolled voltage. The PCB should provide analog ground continuity, short output paths, and filtering appropriate to the expected load and output bandwidth.
Recommandé
Communications Controller
The MSP430F2616TPN fits communication-hub designs that require more than a basic serial interface. Two USCI blocks support I2C, SPI, or UART configurations, allowing the MCU to connect sensors, transceivers, memories, and service interfaces while executing application logic. The 16 MHz CPU can handle protocol processing and real-time tasks, and DMA reduces CPU involvement during supported peripheral transfers. Firmware architecture should assign each USCI instance deliberately, reserve pins for alternate functions, and verify that simultaneous interface activity does not exceed timing or multiplexing constraints. For PCB implementation, route serial signals away from analog inputs, maintain defined levels on unused pins, and check rise-time requirements at the selected clock rate.
Recommandé
Low-Power Data Logger
The MSP430F2616TPN can act as the central processor in a low-power data logger that periodically samples analog inputs and stores or transmits measurements. The 92 KB of Flash provides more program storage than many compact control MCUs, while the 4 KB of SRAM can hold acquisition records and working state. I2C and SPI suit external sensors and nonvolatile memory, and UART can transfer summarized data to a host. The industrial temperature range supports equipment exposed to variable ambient conditions. Design the duty cycle around actual sensor and interface activity, retain only required RAM state during idle periods, and place bulk storage behind a serial interface to avoid consuming package pins for parallel data buses.
Recommandé
Actuator and Process Control
The MSP430F2616TPN is appropriate for compact actuator and process-control loops where sensors, control calculations, and drive signals share one board. A 12-bit ADC measures process variables, the CPU executes control logic, and two 12-bit DAC channels can create analog command signals for amplifiers, valves, or transducers. Its two USCI blocks allow independent serial connections to local sensors and supervisory equipment, while DMA can reduce processor intervention during supported transfers. A practical implementation should separate analog and digital return paths, define fail-safe states for the DAC outputs, and include watchdog and reset behavior in firmware. Thermal and current requirements of external actuators should be handled outside the MCU rather than imposed directly on its pins.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MSP430F2616TPN — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit |
|---|---|
| Package | 80-pin LQFP, 12 x 12 mm |
| Brand | Texas Instruments |
| CPU Architecture | 16-bit RISC |
| Maximum Clock Frequency | 16 MHz |
| Flash Memory | 92 KB |
| SRAM | 4 KB |
| ADC | 12-bit ADC |
| DAC | Dual 12-bit DAC |
| Serial Interfaces | I2C, SPI, UART, and two USCI blocks |
| Special Features | Hardware multiplier and DMA |
| Supply Voltage | 2.5 V or 3.3 V |
| Operating Temperature | -40 °C to 105 °C |
Principaux différenciateurs
- Integrated dual-DAC mixed-signal capability (vs MSP430F2417TPN)
- Substantial on-chip Flash for embedded firmware (vs MSP430F2417TPN)
- Multiple dedicated serial-controller resources (vs MSP430F2417TPN)
- Industrial temperature coverage (vs MSP430F2616TPNR)
Notes de conception
Route the 12-bit ADC inputs and DAC outputs as short, quiet analog nets, and keep switching or high-current digital paths physically separated from them. Place analog bypass capacitors close to the associated supply and ground pins, with a dedicated analog ground region connected according to the manufacturer layout guidance. The 80-pin LQFP footprint provides ample signal access, but analog and digital return currents must not share a path that causes measurement-dependent disturbances.
Assign the two USCI blocks and all analog functions during schematic design because alternate peripheral functions can constrain the usable pin matrix. Check every selected pin against the MSP430F2616 pin-description table, reserve unused inputs in a defined state, and confirm that reset and debug functions are not accidentally reused. Place oscillator, reset, and decoupling components in accordance with the reference layout before authorizing the PCB footprint.
Base the power budget on the active peripherals that will actually be enabled, including the ADC, DAC, communication interfaces, and I/O loads. The 2.5 V and 3.3 V supply options do not imply identical internal operating points, so use the electrical-characteristics tables for each voltage. Firmware should disable unused converters and interfaces before low-power entry, and external actuator or sensor loads must not be powered directly from MCU pins.
Do not treat MSP430F2617TPM, MSP430F2417TPN, or similar family members as drop-in substitutes merely because they are MSP430 devices. The MSP430F2417TPN appears in an 80-pin LQFP comparison, but the available information does not prove matching pin assignments, memory, analog channels, or peripheral multiplexing. Likewise, MSP430F2616TPNR changes the ordering or packing designation and should be used only after production packaging requirements have been confirmed.
Informations de conformité
The manufacturer product information identifies an industrial-grade mixed-signal MCU but does not provide extractable RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations.