MSP430F2616TPN - 16MHz Mixed-Signal MCU | Texas Instruments
料号: MSP430F2616TPN ✓ 量产中MSP430F2616TPN 概述
A mixed-signal microcontroller combines a digital processor with analog conversion and interface peripherals. Within the semiconductor hierarchy, the MSP430F2616TPN is an ultra-low-power MCU, a 16-bit RISC controller, and a mixed-signal embedded-processing device. Its 92 KB Flash supports firmware and application code, while 4 KB of SRAM provides working memory for real-time acquisition, control, and communication tasks.
The principal features include 16 MHz maximum clock operation, a 16-bit RISC architecture, a 12-bit ADC, dual 12-bit DAC outputs, and communication interfaces covering I2C, SPI, and UART. Two USCI blocks provide hardware support for serial communications, while DMA reduces the need for CPU intervention during peripheral transfers. The hardware multiplier is useful for signal-processing and control algorithms that benefit from efficient multiplication.
The MSP430 architecture is designed around low-power embedded control. Its peripheral integration allows a system to acquire analog measurements, perform computations, generate analog outputs, and exchange data through serial interfaces without requiring separate converters. This combination is especially useful when board area, energy use, and external component count are important. The MCU supports an industrial temperature range of -40 °C to 105 °C according to the Texas Instruments part-details listing.
Typical implementations include industrial sensor acquisition, low-power instrumentation, portable measurement equipment, actuator control, and connected embedded systems. The dual DAC can support reference or control outputs, while the ADC accommodates analog sensor inputs. I2C and SPI suit short-distance peripheral connections, and UART provides a straightforward interface for programming, diagnostics, or external controllers.
A practical design must account for the 80-pin LQFP footprint, separate analog and digital supply decoupling, and careful routing around high-impedance analog inputs. Firmware should also configure the unused peripheral pins and avoid leaving unnecessary communication interfaces or converters active in low-power operating states.
This page combines the MSP430F2616TPN device configuration with package information, application guidance, interface-focused comparisons, and replacement-selection criteria. It is intended to help engineers identify whether the MSP430F2616TPN provides the required mixed-signal resources before beginning PCB and firmware development.
直接替换替代料: MSP430F2616TPN ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MSP430F2616TPN (相同外形与封装尺寸) ——差异在于 ADC Resolution, CPU Architecture, Hardware Multiplier, Package, SRAM.
该产品暂无直接替换替代料。
请求替代料MSP430F2616TPN 最大额定值与电气特性
| CPU Architecture | 16-bit RISC |
| 最大时钟频率 | 16 MHz |
| Flash Memory | 92 KB |
| SRAM | 4 KB |
| ADC Resolution | 12 bit |
| DAC Resolution | 12 bit |
| DAC Channels | 2 channels |
| Serial Communication Interfaces | I2C, SPI, and UART |
| USCI Blocks | 2 blocks |
| Hardware Multiplier | Present |
| Direct Memory Access | Present |
| 电源电压 | 2.5 V or 3.3 V |
| 工作温度 | -40 °C to 105 °C |
| 封装 | 80-pin LQFP, 12 x 12 mm |
| Terminal Count | 80 pins |
| 安装类型 | Surface mount |
| Temperature Grade | Industrial |
| RoHS 状态 | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
MSP430F2616TPN 80-pin lqfp, 12 x 12 mm 引脚配置指南
MSP430F2616TPN(80-pin lqfp, 12 x 12 mm 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: MSP430F2616TPN.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MSP430F2616TPN 适用于 6 应用s: Industrial Sensor Acquisition, Portable Measurement Equipment, Programmable Analog Output Control, Communications Controller, Low-Power Data Logger, Actuator and Process Control.
Industrial Sensor Acquisition
The MSP430F2616TPN fits industrial sensor-acquisition systems that need both analog measurement and local control in one package. Its 12-bit ADC samples analog inputs, while the 16 MHz CPU can perform filtering, calibration, and threshold decisions before forwarding results. Four kilobytes of SRAM provides working space for acquisition buffers and control variables, and 92 KB of Flash accommodates firmware, lookup tables, and configuration data. The -40 °C to 105 °C industrial range supports equipment operating across demanding ambient conditions. Place the analog inputs near the ADC pins, use a quiet reference and local decoupling, and isolate sensitive sensor traces from switching and digital outputs to preserve measurement quality.
推荐
Portable Measurement Equipment
The MSP430F2616TPN is suitable for portable instruments that combine analog measurement, data processing, and low-power serial communication. Its 16-bit RISC core supports responsive control and signal calculations at clock rates up to 16 MHz, while the integrated 12-bit ADC removes the need for a separate converter in many designs. Two 12-bit DAC channels can generate test signals, excitation levels, or calibration outputs, and I2C, SPI, and UART support external sensors, storage, and host computers. Because the MCU is designed for low-power operation, firmware should use the appropriate standby or shutdown states between measurements. Power budgeting must include ADC, DAC, interface, and I/O activity rather than relying on a single nominal current figure.
推荐
Programmable Analog Output Control
The MSP430F2616TPN can serve as the controller in systems requiring accurate programmable analog outputs. Its two 12-bit DAC channels are useful for equipment setpoints, actuator commands, sensor excitation, or waveform generation, while the ADC can close the loop by measuring the resulting analog condition. The 16 MHz processor provides enough control bandwidth for common feedback tasks, and the hardware multiplier supports filtering and calibration calculations. Firmware should establish a defined startup sequence for the DAC outputs so that external equipment does not receive an uncontrolled voltage. The PCB should provide analog ground continuity, short output paths, and filtering appropriate to the expected load and output bandwidth.
推荐
Communications Controller
The MSP430F2616TPN fits communication-hub designs that require more than a basic serial interface. Two USCI blocks support I2C, SPI, or UART configurations, allowing the MCU to connect sensors, transceivers, memories, and service interfaces while executing application logic. The 16 MHz CPU can handle protocol processing and real-time tasks, and DMA reduces CPU involvement during supported peripheral transfers. Firmware architecture should assign each USCI instance deliberately, reserve pins for alternate functions, and verify that simultaneous interface activity does not exceed timing or multiplexing constraints. For PCB implementation, route serial signals away from analog inputs, maintain defined levels on unused pins, and check rise-time requirements at the selected clock rate.
推荐
Low-Power Data Logger
The MSP430F2616TPN can act as the central processor in a low-power data logger that periodically samples analog inputs and stores or transmits measurements. The 92 KB of Flash provides more program storage than many compact control MCUs, while the 4 KB of SRAM can hold acquisition records and working state. I2C and SPI suit external sensors and nonvolatile memory, and UART can transfer summarized data to a host. The industrial temperature range supports equipment exposed to variable ambient conditions. Design the duty cycle around actual sensor and interface activity, retain only required RAM state during idle periods, and place bulk storage behind a serial interface to avoid consuming package pins for parallel data buses.
推荐
Actuator and Process Control
The MSP430F2616TPN is appropriate for compact actuator and process-control loops where sensors, control calculations, and drive signals share one board. A 12-bit ADC measures process variables, the CPU executes control logic, and two 12-bit DAC channels can create analog command signals for amplifiers, valves, or transducers. Its two USCI blocks allow independent serial connections to local sensors and supervisory equipment, while DMA can reduce processor intervention during supported transfers. A practical implementation should separate analog and digital return paths, define fail-safe states for the DAC outputs, and include watchdog and reset behavior in firmware. Thermal and current requirements of external actuators should be handled outside the MCU rather than imposed directly on its pins.
推荐
推荐产品汇总
工程参考数据: MSP430F2616TPN ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Package | 80-pin LQFP, 12 x 12 mm |
| Brand | Texas Instruments |
| CPU Architecture | 16-bit RISC |
| Maximum Clock Frequency | 16 MHz |
| Flash Memory | 92 KB |
| SRAM | 4 KB |
| ADC | 12-bit ADC |
| DAC | Dual 12-bit DAC |
| Serial Interfaces | I2C, SPI, UART, and two USCI blocks |
| Special Features | Hardware multiplier and DMA |
| Supply Voltage | 2.5 V or 3.3 V |
| Operating Temperature | -40 °C to 105 °C |
关键差异点
- Integrated dual-DAC mixed-signal capability (对比 MSP430F2417TPN)
- Substantial on-chip Flash for embedded firmware (对比 MSP430F2417TPN)
- Multiple dedicated serial-controller resources (对比 MSP430F2417TPN)
- Industrial temperature coverage (对比 MSP430F2616TPNR)
设计说明
Route the 12-bit ADC inputs and DAC outputs as short, quiet analog nets, and keep switching or high-current digital paths physically separated from them. Place analog bypass capacitors close to the associated supply and ground pins, with a dedicated analog ground region connected according to the manufacturer layout guidance. The 80-pin LQFP footprint provides ample signal access, but analog and digital return currents must not share a path that causes measurement-dependent disturbances.
Assign the two USCI blocks and all analog functions during schematic design because alternate peripheral functions can constrain the usable pin matrix. Check every selected pin against the MSP430F2616 pin-description table, reserve unused inputs in a defined state, and confirm that reset and debug functions are not accidentally reused. Place oscillator, reset, and decoupling components in accordance with the reference layout before authorizing the PCB footprint.
Base the power budget on the active peripherals that will actually be enabled, including the ADC, DAC, communication interfaces, and I/O loads. The 2.5 V and 3.3 V supply options do not imply identical internal operating points, so use the electrical-characteristics tables for each voltage. Firmware should disable unused converters and interfaces before low-power entry, and external actuator or sensor loads must not be powered directly from MCU pins.
Do not treat MSP430F2617TPM, MSP430F2417TPN, or similar family members as drop-in substitutes merely because they are MSP430 devices. The MSP430F2417TPN appears in an 80-pin LQFP comparison, but the available information does not prove matching pin assignments, memory, analog channels, or peripheral multiplexing. Likewise, MSP430F2616TPNR changes the ordering or packing designation and should be used only after production packaging requirements have been confirmed.
合规信息
The manufacturer product information identifies an industrial-grade mixed-signal MCU but does not provide extractable RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations.