MSP430F4371IPN - 8MHz 16-Bit MCU with 32KB Flash | TI
Référence : MSP430F4371IPN ✓ ActifMSP430F4371IPN Présentation
An ultra-low-power mixed-signal microcontroller is a semiconductor device that integrates a CPU, memory, analog functions, and communication peripherals into one compact component. The MSP430 architecture uses 16-bit registers and constant generators to support efficient embedded software execution, while its low-power modes are intended to extend battery life in systems that spend substantial time asleep.
The MSP430F4371IPN operates at up to 8 MHz and includes 32 KB of Flash for program storage plus 1 KB of SRAM for data. Its integrated comparator supports basic analog threshold and signal-conditioning tasks, while SPI and UART interfaces enable connection to sensors, displays, transceivers, and data-acquisition equipment. A 160-segment LCD capability can also reduce the need for separate display-driver circuitry in segmented-panel designs.
The device belongs to the MSP430x43x mixed-signal family and uses the MSP430 CPU16 architecture. Its combination of 16-bit processing, Flash memory, SRAM, comparator resources, serial interfaces, and LCD support is useful where designers want one controller to handle both control logic and local human-interface functions. The 80-pin LQFP (PN) package provides substantially more I/O and peripheral connectivity than the smaller MSP430 devices intended for compact, low-pin-count designs.
Typical applications include industrial panel controls, portable measurement instruments, low-power sensor nodes, data loggers, building-control modules, and compact serial-interface equipment. In a measurement product, the comparator can support fast threshold detection while the CPU handles control, calibration, and communications. SPI can connect to higher-bandwidth sensors or memory, while UART provides a simple interface for configuration and diagnostics.
Designers should assign pins from the manufacturer pin-description table and verify the complete pin multiplexing, LCD-segment mapping, and peripheral-instance assignments for the selected firmware. The 80-LQFP layout also requires careful examination of exposed-pad, thermal, and board-routing requirements where those are specified for the package. Software configuration must account for the shared analog and digital peripheral resources rather than assuming every function is simultaneously available.
This page combines the exact device identity, package, memory, interface, and temperature information with focused replacement guidance and engineering-oriented selection notes. It also distinguishes electrically similar MSP430 family members from confirmed drop-in choices, helping engineers assess PCB compatibility, firmware implications, and application suitability before committing to a replacement.
Alternatives de remplacement direct pour MSP430F4371IPN — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MSP430F4371IPN (même facteur de forme et même empreinte) — différant par Flash Memory, CPU Architecture, Comparator, Operating Temperature, Package.
MSP430F435IPN
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MSP430F436IPN
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →MSP430F4376IPN
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MSP430F4377IPN
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MSP430F4371IPN Valeurs maximales et caractéristiques électriques
| Product Type | 16-bit ultra-low-power mixed-signal microcontroller |
| CPU Architecture | MSP430 CPU16 |
| Fréquence d'horloge maximale | 8 MHz |
| Word Size | 16 bit |
| Flash Memory | 32 KB |
| SRAM | 1 KB |
| Additional Flash Detail | 256 byte |
| Comparator | Integrated |
| SPI Interface | Integrated |
| UART Interface | Integrated |
| LCD Segment Support | 160 segments |
| Boîtier | 80-pin LQFP (PN), 12 mm x 12 mm |
| Type de montage | Surface mount |
| Température de fonctionnement | -40 °C to +85 °C |
| Product Category | Mixed-signal microcontroller |
Guide de configuration des broches du MSP430F4371IPN 80-pin lqfp (pn), 12 mm x 12 mm
Configuration des broches du MSP430F4371IPN (boîtier 80-pin lqfp (pn), 12 mm x 12 mm). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour MSP430F4371IPN.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MSP430F4371IPN convient pour 6 applications: Industrial LCD Control Panel, Portable Data Logger, Battery-Powered Sensor Node, Serial Measurement Instrument, Building Control Module, Configuration and Diagnostics Interface.
Industrial LCD Control Panel
The MSP430F4371IPN fits industrial panel designs that require substantial display capability and local control in one controller. Its support for 160 LCD segments can drive a segmented status display while the 16-bit MSP430 CPU handles button logic, alarms, configuration, and supervisory tasks. The 80-pin LQFP (PN) package provides a substantial I/O budget for keys, indicator control, communication, and discrete sensing. With 32 KB of Flash and 1 KB of SRAM, the device can host application code and working data for a dedicated panel controller. Engineers should map segment outputs directly from the manufacturer LCD tables and reserve pins for required peripherals before committing the board layout.
Recommandé
Portable Data Logger
The MSP430F4371IPN is suitable for a portable logger combining an 8 MHz control core, 32 KB Flash, and 1 KB SRAM with low-power MSP430 operation. The CPU can coordinate sensor acquisition, timestamps, local status indication, and serial data transfer, while SPI provides a path to higher-speed sensors or storage and UART supports configuration or synchronization. Battery-operated operation makes low-power mode selection, interrupt-driven sampling, and peripheral shutdown behavior central to the design. The 80-pin LQFP package also leaves enough external connectivity for sensors, a battery monitor, and protection circuitry. Validate worst-case memory usage and wake-up behavior in the intended firmware configuration.
Recommandé
Battery-Powered Sensor Node
The MSP430F4371IPN can serve as the local controller in a battery-powered sensor node that needs more serial connectivity and display flexibility than a minimal MSP430 design. Its integrated comparator supports fast threshold or signal-change detection, the 8 MHz CPU performs acquisition logic, and SPI or UART connects the node to sensors and an external radio. The 32 KB Flash provides room for protocol and application code, while 1 KB SRAM accommodates active buffers and stack requirements. Because the MCU alone does not determine total battery life, the system designer should minimize peripheral run time and use event-driven wake-up behavior. The 80-pin LQFP footprint is helpful when multiple sensing and communication lines are required.
Recommandé
Serial Measurement Instrument
The MSP430F4371IPN is appropriate for a compact measurement instrument that combines acquisition control with a local readout and serial data exchange. The comparator provides a basic analog comparison function, SPI can connect to precision converters or sensors, and UART can carry commands, results, and diagnostics. Its 16-bit CPU and 32 KB Flash support structured control software, while 1 KB SRAM is suitable for modest working sets and buffered results. A segmented LCD can present operating state without adding a dedicated display controller. In implementation, verify comparator input ranges, ADC needs, peripheral multiplexing, and timing against the manufacturer electrical tables. The 80-pin package offers ample connectivity for analog conditioning and user-interface signals.
Recommandé
Building Control Module
The MSP430F4371IPN can act as a low-power building-control module when a design combines distributed sensing with local status display and serial connectivity. Its 160-segment LCD capability can drive zone indicators or a service display, while comparator inputs can provide threshold detection for simple analog conditions. SPI and UART permit connection to environmental sensors, gateways, and service interfaces, and the 32 KB Flash provides sufficient storage for structured control logic. The 80-pin LQFP (PN) package simplifies access to a broad set of I/O resources for switches, indicators, and interconnects. Designers should define power states carefully to avoid unnecessary peripheral current and confirm that the LCD and communication interfaces can operate concurrently in the selected device configuration.
Recommandé
Configuration and Diagnostics Interface
The MSP430F4371IPN works well as a configuration and diagnostics interface for an embedded product that needs more processing and display resources than a basic serial bridge. Its 8 MHz MSP430 CPU can manage menus, status pages, input handling, logs, and command processing, while UART provides a direct host interface and SPI supports local expansion. The integrated 160-segment LCD capability can show operating modes, diagnostics, and calibration information without a separate display MCU. With 32 KB Flash and 1 KB SRAM, application organization should account for code growth, communication buffers, and stack depth. The 80-pin package leaves ample pins for buttons, indicators, and expansion buses, but every alternate peripheral function must be checked against the manufacturer pin-mux rules.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MSP430F4371IPN — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MSP430F435IPN | MSP430F436IPN | MSP430F4376IPN | MSP430F4377IPN |
|---|---|---|---|---|---|
| Package | 80-pin LQFP (PN), 12 mm x 12 mm | 80-pin LQFP (PN), 12 mm x 12 mm | 80-pin LQFP (PN), 12 mm x 12 mm | 80-pin LQFP (PN), 12 mm x 12 mm | 80-pin LQFP (PN), 12 mm x 12 mm |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
Principaux différenciateurs
- Largest explicitly documented LCD segment capability in the comparison set (vs MSP430F435IPN)
- 32 KB Flash and 1 KB SRAM for local application code and working data (vs MSP430F4377IPN)
- Integrated comparator plus SPI and UART in one mixed-signal controller (vs MSP430F436IPN)
Notes de conception
Plan the power tree around the MSP430's active and low-power states, including every external sensor, transceiver, and LCD load. The MCU can operate at 8 MHz, but clock choice and peripheral activity materially affect current draw. Use the manufacturer power-supply and decoupling recommendations, place bulk and high-frequency capacitors close to the relevant pins, and avoid allowing unused analog or communication resources to remain active when the firmware enters a low-energy state.
Do not infer the 80-pin LQFP (PN) netlist from the general MSP430x43x family description. Start with the manufacturer pin-description table, then assign LCD segments, comparator inputs, SPI, UART, clock, reset, and power pins using the intended peripheral multiplexing. Preserve the package's thermal and electrical layout exactly, and route sensitive analog comparator inputs away from fast-switching nodes to reduce coupling into measurement thresholds.
A shared 80-pin footprint does not guarantee drop-in firmware compatibility. Before substituting an MSP430x43x member, compare memory size, LCD segment maps, analog-channel assignments, port-mux options, interrupt vectors, clock initialization, and peripheral-instance locations. In particular, verify whether the replacement supports all 160 LCD segments used by the target design and whether code relies on the target device's 32 KB Flash and 1 KB SRAM boundaries.
Keep SPI traces short and continuous, provide a defined ground reference close to the interface, and route them away from comparator inputs and switching power nodes. For UART, minimize unnecessary stubs and maintain signal levels appropriate to the selected logic voltage. If the LCD is used, place its drive connections according to the manufacturer recommended layout and keep external analog conditioning components away from high-current switching paths to preserve reliable threshold detection.
Informations de conformité
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements were included in the verified product information. The industrial temperature range does not by itself establish AEC-Q100 qualification.