NC7SZ125M5X - UHS Single Buffer, 3-State, SOT-23-5 | onsemi
Référence : NC7SZ125M5X ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $0.45 | $0,45 |
| 10 | $0.36 | $3,60 |
| 100 | $0.25 | $25,00 |
| 500 | $0.18 | $90,00 |
| 1 000 | $0.13 | $130,00 |
| 3 000 | $0.1 | $300,00 |
NC7SZ125M5X Présentation
A non-inverting buffer (also called a line driver or signal repeater) is a single-input, single-output logic function that reproduces the logic level present at its input at the output, providing current gain and isolation between a weak source and a heavier load. Within the broader logic IC hierarchy, this part belongs to the TinyLogic UHS family from onsemi, a subset of CMOS logic gates that trade absolute speed for low power consumption. The 3-STATE output allows multiple buffers to share a common bus, with the disabled buffer entering a high-impedance state to avoid contention. The SOT-23-5 package is one of the most ubiquitous footprints in modern surface-mount design.
Key features of the NC7SZ125M5X include balanced propagation delays, very low quiescent current (typically 1 µA at room temperature), ±24 mA output drive at 5 V (enabling direct drive of LEDs or small relays), and a wide VCC operating range that makes it compatible with 1.8 V, 2.5 V, 3.3 V, and 5 V logic families. The device contains a single Schmitt-trigger input, providing hysteresis for slow or noisy input edges. Tape and reel packaging (suffix X) supports high-volume automated assembly.
From a technical perspective, the NC7SZ125M5X uses a standard CMOS push-pull output stage. The output enable pin OE is internally pulled high through a weak pull-up, so the output remains in high-impedance until actively driven low. Input structures tolerate voltages up to 5.5 V regardless of VCC, allowing level translation between 1.8 V and 5 V domains. ESD protection exceeds 2000 V HBM per industry standards, and latch-up immunity is rated above 100 mA per JESD78.
Typical applications include signal buffering between low-drive microcontroller GPIOs and heavier loads such as LEDs, level translation between mixed-voltage logic domains (e.g., 1.8 V to 3.3 V), bus isolation and multiplexing in distributed systems, and general-purpose logic inversion-free signal restoration in handheld and battery-powered designs. In industrial PLCs, it isolates backplane logic from field-side noise. In consumer audio and wearables, it buffers buttons or I2C lines between SoCs and accessory connectors.
When designing with this part, ensure OE is driven to a defined logic level rather than left floating, especially in noisy environments, to avoid inadvertent bus contention. Place a 0.1 µF decoupling capacitor close to the VCC pin to suppress logic-stage switching transients, and avoid exceeding the absolute maximum VCC of 6 V. This TinyLogic buffer excels where a single-bit driver, three-state capability, and tiny footprint are required simultaneously.
This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives, comparison parameters, and practical design notes that go beyond what is printed in the manufacturer datasheet alone, giving engineers a faster path from selection to validated PCB layout.
Alternatives de remplacement direct pour NC7SZ125M5X — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec NC7SZ125M5X (même facteur de forme et même empreinte) — différant par Operating Temperature, MSL Level, RoHS Status, Function, Input Voltage Tolerance.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
NC7SZ125P5X
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
NC7SZ125FHX
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
NC7SZ125L6X
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
SN74LVC1G125DBVR
✅ Remplacement direct✓ En stock
$0.13 / unité
Voir la fiche technique →74LVC1G125GV
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
NLU1G125M5X
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MC74VHC1G125DF1G
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
NC7SZ125M5X Valeurs maximales et caractéristiques électriques
| Logic Type | Buffer, Non-Inverting |
| Number of Elements | 1 |
| Number of Bits per Element | 1 |
| Type de sortie | 3-State |
| Supply Voltage (VCC) | 1.65 V to 5.5 V |
| Input Voltage Tolerance | 0 V to 5.5 V (over-voltage tolerant) |
| Propagation Delay (typ @ 5 V) | 2.6 ns |
| Output Drive (IOH/IOL @ 5 V) | ±24 mA |
| Quiescent Current (typ) | 1 µA |
| Input Type | Schmitt Trigger (with hysteresis) |
| Output Enable (OE) | Active-low, internal pull-up |
| Température de fonctionnement | -40 °C to +85 °C |
| Boîtier / Format | SOT-23-5 (M5) |
| Type de montage | Surface Mount |
| Niveau MSL | 1 |
| Statut RoHS | Compliant |
| Family / Series | TinyLogic UHS |
| Technology | CMOS |
Configuration des broches de NC7SZ125M5X
| Broche 1 | OE — Output Enable, with internal pull-up; LOW = enabled, HIGH = high-impedance |
| Broche 2 | GND — Ground reference |
| Broche 3 | A — Data input |
| Broche 4 | Y — Data output (3-State) |
| Broche 5 | VCC — Supply voltage (1.65 V to 5.5 V) |
Applications typiques
NC7SZ125M5X convient pour 6 applications: GPIO Buffer for Microcontrollers, Level Translation Between Logic Domains, Bus Isolation and Multiplexing, Handheld and Battery-Powered Devices, Industrial PLC Logic Isolation, LED Driving and Indicator Circuits.
GPIO Buffer for Microcontrollers
The NC7SZ125M5X's 2.6 ns propagation delay and ±24 mA drive at 5 V make it ideal for buffering low-drive microcontroller GPIOs to heavier downstream loads. Placed between a Cortex-M MCU GPIO and an LED array or relay driver input, it isolates the MCU pin from back-EMF while providing a clean, low-impedance logic edge. Unlike a discrete MOSFET, it adds no quiescent leakage (typically 1 µA) and occupies only 2.9 x 1.6 mm of PCB area in SOT-23-5. The 3-STATE OE pin also enables multi-source bus multiplexing without contention.
Recommandé
Level Translation Between Logic Domains
The NC7SZ125M5X's 1.65 V to 5.5 V VCC range and 5.5 V-tolerant inputs support unidirectional level translation between mixed-voltage domains - for example, 1.8 V SoC to 3.3 V peripheral, or 3.3 V to 5 V bus. With the input driven from a 1.8 V logic signal and VCC at 3.3 V, the output swings the full 0 V to 3.3 V rail cleanly within 2.6 ns. This is faster and lower-power than a discrete MOSFET level shifter, and the SOT-23-5 footprint makes it ideal for space-constrained wearables and IoT modules.
Recommandé
Bus Isolation and Multiplexing
The active-low 3-STATE output enable on the NC7SZ125M5X allows multiple buffers to share a common bus, with the disabled buffer entering high-impedance to avoid contention. In a distributed sensor array, individual sensor outputs can be wire-ORed to a single MCU ADC input, with each sensor's OE controlled by a chip-select line. The 2.6 ns propagation delay supports >100 MHz bus operation, while the 1 µA quiescent current ensures minimal impact on battery life in portable instruments.
Recommandé
Handheld and Battery-Powered Devices
With a typical quiescent current of only 1 µA across the full 1.65 V to 5.5 V VCC range, the NC7SZ125M5X is purpose-built for handheld and battery-powered applications. In a BLE wearable, it can buffer a button-press signal from a coin-cell domain to the SoC's GPIO without draining the battery, even when continuously enabled. The SOT-23-5 footprint is one of the smallest 5-pin packages available, enabling compact PCB layouts in fitness bands and medical patches.
Recommandé
Industrial PLC Logic Isolation
In industrial PLC and factory-automation systems, the NC7SZ125M5X provides logic-level isolation between backplane digital logic and field-side signal conditioning. Its 5.5 V input tolerance exceeds typical 3.3 V logic noise margins, and the 2000 V HBM ESD rating protects against field-side transients. The wide -40 °C to +85 °C operating temperature range meets industrial environmental requirements, making it suitable for programmable logic controllers and motor-control interface boards.
Recommandé
LED Driving and Indicator Circuits
The NC7SZ125M5X's ±24 mA output drive at 5 V is sufficient to directly drive small LEDs and indicator circuits without an external driver transistor. In a status-indicator panel, the buffer converts a 1.8 V MCU GPIO signal to a clean 5 V signal capable of sinking 24 mA into a common-anode LED array. The 3-STATE OE pin allows PWM brightness control by toggling enable at high frequency, while the 2.6 ns propagation delay preserves fast switching edges for crisp indicator response.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour NC7SZ125M5X — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | NC7SZ125P5X | NC7SZ125FHX | SN74LVC1G125DBVR | 74LVC1G125GV | NLU1G125M5X |
|---|---|---|---|---|---|---|
| Package | SOT-23-5 (M5) | SC-70-5 (similar 5-pin SMD) | SOT-23-5 | SOT-23-5 (DBV) | SOT-23-5 / TSOP5 | SOT-23-5 |
| Brand | onsemi | onsemi | onsemi | Texas Instruments | Nexperia | onsemi |
| VCC Range | 1.65 V to 5.5 V | 1.65 V to 5.5 V | 1.65 V to 5.5 V | 1.65 V to 5.5 V | 1.65 V to 5.5 V | 1.65 V to 5.5 V |
| Propagation Delay (typ @5V) | 2.6 ns | 2.6 ns | 2.6 ns | 4 ns | 2.5 ns | 2.6 ns |
| Quiescent Current (typ) | 1 µA | 1 µA | 1 µA | 10 µA | 1 µA | 1 µA |
| Output Drive (5 V) | ±24 mA | ±24 mA | ±24 mA | ±24 mA | ±24 mA | ±24 mA |
| Output Enable Polarity | Active-Low (OE) | Active-Low (OE) | Active-Low (OE) | Active-Low (OE) | Active-Low (OE) | Active-Low (OE) |
| Operating Temperature | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +85 °C |
Principaux différenciateurs
- Lower quiescent current for battery-powered designs (vs SN74LVC1G125DBVR)
- Faster propagation delay at 5 V VCC (vs SN74LVC1G125DBVR)
- Smaller SC-70-5 same-family option for tight layouts (vs NC7SZ125P5X)
- Industrial temperature range advantage for harsh environments (vs SN74LVC1G125DBVR)
Notes de conception
Place a 0.1 µF X5R or X7R ceramic decoupling capacitor within 2 mm of the VCC pin (pin 5) to suppress logic-stage switching transients. The NC7SZ125M5X draws sub-microamp quiescent current when idle but produces fast 2.6 ns edges that inject high-frequency noise into the supply rail. Bulk capacitance (1-10 µF) at the board level is recommended for systems with multiple TinyLogic devices switching simultaneously.
Do not leave the OE pin floating in production designs, even though the NC7SZ125M5X has an internal pull-up. Floating OE can pick up noise in electrically noisy environments (motor drives, switch-mode supplies) and toggle the output state unpredictably. Always drive OE from a defined logic source. A floating OE that momentarily enables the buffer while another source drives the bus creates contention that can damage both parts.
The SOT-23-5 footprint is one of the smallest 5-pin SMD packages, but the exposed lead frame on the bottom can create a thermal via array if high-current switching is expected. For standard ±24 mA drive at low duty cycle, no thermal management is required. For continuous high-current loads approaching the absolute maximum, route the GND pin (pin 2) directly to a ground pour to provide a low-impedance return path.
When using the NC7SZ125M5X for high-speed signal conditioning (>50 MHz), keep output traces short (<25 mm) and maintain a 50 Ω characteristic impedance if possible. The 2.6 ns propagation delay corresponds to roughly 50 MHz of usable bandwidth; longer traces will create reflections that corrupt the signal. Place a series damping resistor (22-33 Ω) at the output if driving long cables or connectors.
Informations de conformité
RoHS and REACH compliant per onsemi product page. Lead-free and halogen-free per TinyLogic family datasheet. Not AEC-Q100 qualified - choose automotive-grade SN74LVC1G125QDRQ1 from TI for AEC-Q100 automotive applications.
