OPA2237EA/2K5 - Dual 1.5MHz Op Amp, 750µV Offset | TI
Référence : OPA2237EA/2K5 ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $1.18 | $1,18 |
| 10 | $1.06 | $10,60 |
| 100 | $0.89 | $89,00 |
| 500 | $0.74 | $370,00 |
| 1 000 | $0.62 | $620,00 |
| 2 500 | $0.55 | $1 375,00 |
OPA2237EA/2K5 Présentation
A dual operational amplifier (op amp) is a single integrated circuit that contains two independent op-amp cells sharing common power pins; it is a member of the broader linear IC hierarchy that includes op amps -> amplifiers -> signal conditioning ICs -> analog ICs -> semiconductors. The OPA2237's dual configuration saves PCB area versus two single op amps while keeping channel-to-channel matching tight for instrumentation paths.
Key features include low input bias current (~20 nA), wide bandwidth suitable for active filters and audio preamplifiers, and MicroAmplifier-series miniaturization that targets space-limited portable designs. The 750 µV maximum offset makes the part accurate enough for sensor signal conditioning without external trimming, while the 350 µA quiescent current keeps battery drain modest.
Architecturally, the OPA2237 uses a bipolar input stage optimized for low-offset single-supply operation, with internal compensation that stabilizes the part at unity gain. The wide supply range (±18V or +36V single-supply) lets one part cover both low-voltage battery and higher-voltage industrial signal chains.
Typical applications include battery-powered instrumentation, PCMCIA cards, portable medical devices, transducer amplifiers, and general-purpose signal conditioning in industrial and consumer designs. The MSOP-8 footprint is footprint-compatible with the SOIC-8 OPA2237UA variant for layout reuse.
When designing with this op amp, observe the input common-mode range that includes the negative rail (true single-supply operation) and use a low-impedance ground return to keep offset drift under temperature. Add an output resistor if driving capacitive loads above 1 nF to maintain phase margin.
This page synthesizes verified distributor pricing, drop-in alternatives, comparison data, and engineering design notes not found in the manufacturer datasheet alone.
Alternatives de remplacement direct pour OPA2237EA/2K5 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec OPA2237EA/2K5 (même facteur de forme et même empreinte) — différant par Input Bias Current (typ), Input Offset Voltage (max), Operating Temperature Range, Slew Rate, Supply Voltage Range (Dual).
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
OPA2237EA
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
OPA2237EA/250
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
OPA2237EA/250G4
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
OPA2336E/2K5G4
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
OPA2192IDGKR
✅ Remplacement direct✓ En stock
$1.78 / unité
Voir la fiche technique →OPA2237EA/2K5 Valeurs maximales et caractéristiques électriques
| Number of Channels | 2 (Dual) |
| Amplifier Type | General Purpose, Single-Supply |
| Gain Bandwidth Product | 1.5 MHz |
| Slew Rate | 0.5 V/µs |
| Input Offset Voltage (max) | 750 µV |
| Input Bias Current (typ) | 20 nA |
| Quiescent Current per Channel (max) | 350 µA |
| Supply Voltage Range (Single) | +2.7 V to +36 V |
| Supply Voltage Range (Dual) | ±1.35 V to ±18 V |
| Plage de température de fonctionnement | -40 °C to +85 °C |
| Boîtier / Format | 8-MSOP (VSSOP), 8-pin |
| Type de montage | Surface Mount |
| Packaging | Tape & Reel, 2,500 pcs/reel (/2K5) |
| Series | MicroAmplifier™ |
| Statut RoHS | Compliant |
| Nombre de broches | 8 |
Configuration des broches de OPA2237EA/2K5
| Broche 1 | OUT A — Output of amplifier A |
| Broche 2 | IN- A — Inverting input of amplifier A |
| Broche 3 | IN+ A — Non-inverting input of amplifier A |
| Broche 4 | V- / GND — Negative supply or ground for single-supply operation |
| Broche 5 | IN+ B — Non-inverting input of amplifier B |
| Broche 6 | IN- B — Inverting input of amplifier B |
| Broche 7 | OUT B — Output of amplifier B |
| Broche 8 | V+ — Positive supply |
Applications typiques
OPA2237EA/2K5 convient pour 6 applications: Battery-Powered Sensor Signal Conditioning, Portable Medical Instrumentation, PCMCIA / Card-Sized Industrial Modules, Active Audio Filter and Tone-Control Stages, Transducer and Bridge Amplifiers, General-Purpose Signal Conditioning in PLC and DAQ Systems.
Battery-Powered Sensor Signal Conditioning
The OPA2237EA/2K5's 750 µV maximum input offset and 350 µA quiescent current make it well suited for conditioning low-level sensor signals in Li-ion battery systems. With a single-supply range down to 2.7 V the part can run directly from a single-cell Li-ion or two AA cells, eliminating the need for a negative rail. Its true single-supply input stage that includes the negative rail simplifies bridge-amp circuits for strain gauges and pressure sensors. The 1.5 MHz GBW is sufficient for thermocouple and RTD amplification up to several kHz signal bandwidth.
Recommandé
Portable Medical Instrumentation
The OPA2237EA/2K5 supports portable medical devices where MSOP-8 footprint, low power, and a wide supply range are critical. With ±18 V dual-supply capability the part can handle ECG and EMG front-end signals that swing several volts around ground. The 750 µV offset keeps baseline drift low across body-temperature operating conditions, while 350 µA quiescent current preserves battery life in handheld pulse oximeters and glucose monitors. Bipolar input design gives low input bias current, important for high-impedance electrode interfaces.
Recommandé
PCMCIA / Card-Sized Industrial Modules
Per TI's OPAx237 datasheet, the MicroAmplifier series was designed specifically for PCMCIA cards and other space-limited portable modules where the MSOP-8 footprint of the OPA2237EA/2K5 is a major advantage. The 8-pin MSOP saves roughly 60 percent board area versus SOIC-8, enabling dense multi-channel signal chains on a single card. With +36 V single-supply tolerance, the part survives industrial 24 V bus transients without additional protection, simplifying the BOM.
Recommandé
Active Audio Filter and Tone-Control Stages
The 1.5 MHz gain-bandwidth product and 0.5 V/µs slew rate of the OPA2237EA/2K5 are well matched to active audio filters operating in the 20 Hz to 20 kHz band. Per TI's datasheet, the part offers low total harmonic distortion in audio-band circuits and can serve as a Sallen-Key filter, multiple-feedback low-pass, or Baxandall tone-control stage. The dual-channel package simplifies stereo implementations, and the wide supply range supports both 5 V USB-powered headphone amps and ±15 V hi-fi signal chains.
Recommandé
Transducer and Bridge Amplifiers
The OPA2237EA/2K5's low 750 µV offset and 20 nA bias current give it adequate accuracy for strain-gauge bridges, load-cell amplifiers, and pressure-sensor front-ends. Per TI's application notes, the dual channel lets one IC handle both halves of a differential bridge excitation and read-back path. The single-supply capability from 2.7 V upward simplifies 3.3 V or 5 V transducer designs while the ±18 V dual-supply rating supports industrial 4-20 mA current-loop read-back electronics.
Recommandé
General-Purpose Signal Conditioning in PLC and DAQ Systems
Per TI's product page, the OPA2237EA/2K5 targets general-purpose signal conditioning in industrial PLC and DAQ modules where multi-channel analog front-ends interface with 4-20 mA loops, thermocouples, and 0-10 V signals. The 750 µV offset, ±18 V supply, and 8-pin MSOP make it a flexible building block. Its low 350 µA quiescent current lets designers place multiple OPA2237 chips per module without thermal concerns, and the dual package keeps the BOM count low versus dual SOIC-8 singles.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour OPA2237EA/2K5 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | OPA2237EA | OPA2237EA/250 | OPA2237EA/250G4 | OPA2336E/2K5G4 | OPA2192IDGKR |
|---|---|---|---|---|---|---|
| Package | MSOP-8 (VSSOP-8) | MSOP-8 (VSSOP-8) - same | MSOP-8 (VSSOP-8) - same | MSOP-8 (VSSOP-8) - same | MSOP-8 (VSSOP-8) - same | MSOP-8 (DGK) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Gain Bandwidth Product | 1.5 MHz | 1.5 MHz | 1.5 MHz | 1.5 MHz | 0.1 MHz | 10 MHz |
| Quiescent Current per Channel (max) | 350 µA | 350 µA | 350 µA | 350 µA | 20 µA | 1000 µA |
| Slew Rate | 0.5 V/µs | 0.5 V/µs | 0.5 V/µs | 0.5 V/µs | 0.03 V/µs | 20 V/µs |
| Supply Voltage Range (Single) | +2.7 V to +36 V | +2.7 V to +36 V | +2.7 V to +36 V | +2.7 V to +36 V | +2.7 V to +5.5 V | +4.5 V to +36 V |
| RoHS / Lead-Free | Yes | Yes | Yes | Yes | Yes | Yes |
Principaux différenciateurs
- Wide single-supply range up to +36 V (vs OPA2336E/2K5G4)
- 10x lower quiescent current vs OPA2192 (vs OPA2192IDGKR)
- MicroAmplifier-series miniaturization in MSOP-8 (vs OPA2237UA (SOIC-8))
Notes de conception
Place a 0.1 µF ceramic bypass capacitor as close as possible to the V+ pin (pin 8) of the OPA2237EA/2K5 to decouple high-frequency noise. Per TI's OPAx237 datasheet, additional bulk capacitance (1 µF to 10 µF) may be required if the op amp is more than a few centimeters from the main regulator. Keep the input traces short and guarded if high-impedance sensor signals are connected, and use a ground plane to minimize parasitic coupling between the two channels in the same MSOP-8 package.
Do not assume rail-to-rail output swing. Per TI's datasheet, the OPA2237's output stage does NOT swing to both rails; with a 5 V supply the typical output swing is within ~1 V of each rail at 1 mA load. For rail-to-rail output, choose OPA2192 instead. Also note that although the input common-mode range INCLUDES the negative rail (true single-supply input), exceeding the positive rail by more than 0.5 V can damage the input stage; add series input resistors if transients above V+ are possible.
When using the OPA2237EA/2K5 to drive capacitive loads above ~200 pF directly, add an isolation resistor of 20-50 Ω between the output and the load to preserve phase margin. Per TI's application notes, the part is internally compensated for unity-gain stability but may oscillate with heavy capacitive loading. For ADC driver applications, place a small series resistor plus a 1 nF to 10 nF capacitor on the output to form a noise/charge-kickback filter without exceeding the amplifier's capacitive-load drive limit.
Estimated: At maximum quiescent current of 350 µA per channel, the OPA2237EA/2K5 dissipates roughly 350 µA × 2 channels × V+ = 2.1 mW at 3 V supply or 25 mW at 36 V supply. The MSOP-8 package thermal resistance θJA is approximately 200 °C/W per JEDEC EIA/JESD51 standards, so the junction temperature rise is negligible (<5 °C) under normal conditions. No heatsink is required; however, ensure the PCB copper area around pins 4 and 8 (power pins) provides adequate thermal dissipation if the part is used in a high-channel-density module.
Informations de conformité
RoHS compliant per TI's OPAx237 product page. Not AEC-Q100 qualified; choose an automotive-grade dual op amp (e.g., OPA2333-Q1) for vehicle applications. Lead-free matte-tin terminations per JEDEC J-STD-020 reflow profiles.
