OPA234PA - Low-Power Precision Dual Op Amp | Texas Instruments
Référence : OPA234PA ✓ ActifOPA234PA Présentation
An operational amplifier is an active semiconductor device that uses high-gain differential amplification and negative feedback to create stable, accurate gain. The dual-amplifier configuration places two amplifiers in one package, allowing instrumentation, filtering, buffering, and signal-conditioning circuits to share a common package. The OPA234PA belongs to the low-power, precision single-supply operational-amplifier category and is intended to balance low current consumption with precision-oriented analog performance.
The main application advantages of the OPA234PA are its dual amplifier arrangement, wide supply-voltage capability, and low quiescent current. A dual amplifier can reduce the number of packages required in a circuit that needs two independent gain stages, while the low 250 µA per-amplifier quiescent current is relevant to battery-powered or otherwise power-constrained equipment. The device can also be used with either a single positive supply or split positive and negative supplies, depending on the signal and output-voltage requirements of the application.
OPA234PA is appropriate for precision measurement front ends, low-frequency active filters, sensor conditioning, audio and communications signal paths, and general-purpose analog processing. When using the device with a single supply, the input and output common-mode limits must be considered carefully. Decoupling capacitors should be placed close to the supply pins, and the unused amplifier section should be configured according to the manufacturer’s recommended practice to avoid instability or unintended oscillation.
This page combines the manufacturer and distributor product information for OPA234PA with application guidance, package details, specification gaps, and drop-in replacement analysis. Because the available material does not expose the complete manufacturer pin description table or detailed electrical limits, those values should be confirmed in the official OPA234 datasheet before final circuit release, qualification, or production use.
Alternatives de remplacement direct pour OPA234PA — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Aucune alternative de remplacement direct disponible pour ce produit.
Demander des alternativesOPA234PA Valeurs maximales et caractéristiques électriques
| Product Type | Dual precision operational amplifier |
| Number of Amplifiers | 2 amplifiers |
| Supply Voltage Range, Single Supply | Up to 36 V |
| Supply Voltage Range, Dual Supply | ±18 V |
| Guaranteed Performance Supplies | +2.7 V, +5 V, and ±15 V |
| Courant de repos | 250 µA per amplifier |
| Boîtier | 8-pin PDIP |
| Nombre de broches | 8 pins |
| Type de montage | Through-hole |
| Catégorie | Operational amplifier |
| Application Class | Precision analog signal conditioning |
| Supply Configuration | Single-supply or dual-supply operation |
Guide de configuration des broches du OPA234PA 8-pin pdip
Configuration des broches du OPA234PA (boîtier 8-pin pdip). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour OPA234PA.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
OPA234PA convient pour 6 applications: Portable Sensor Signal Conditioning, Precision Low-Frequency Active Filter, General-Purpose Instrumentation Amplifier, Low-Power Audio Preamplifier, Communications Interface Buffering, Precision Voltage Reference Buffer.
Portable Sensor Signal Conditioning
OPA234PA is well suited to portable sensor-conditioning blocks because it combines two precision amplifiers with a 250 µA per-amplifier quiescent-current specification. The device can operate from +2.7 V, allowing the signal chain to run directly from a low-voltage source when the sensor output remains inside the input common-mode range. One section can amplify or filter the sensor signal while the second can provide level shifting, gain, or active filtering. Low quiescent current helps limit continuous battery drain, while the dual package reduces board area compared with two separate amplifiers.
Recommandé
Precision Low-Frequency Active Filter
OPA234PA can implement a two-amplifier active-filter section where low power and precision are more important than high-speed operation. Its dual-amplifier arrangement supports cascaded low-pass or notch stages using the same 8-pin PDIP package. The device is compatible with +2.7 V, +5 V, and ±15 V supply arrangements, enabling the same general topology to serve portable, laboratory, and industrial systems. Component tolerances, capacitor selection, and the amplifier’s gain-bandwidth behavior remain critical because those values determine filter accuracy and stability.
Recommandé
General-Purpose Instrumentation Amplifier
OPA234PA can support a classic three-op-amp instrumentation-amplifier topology when two amplifier sections are combined with a third external amplifier. Its low 250 µA per-amplifier quiescent current reduces the bias burden of the two internal sections, while the precision-oriented family is appropriate for slow measurement signals from strain gauges, temperature sensors, and resistive bridges. The circuit requires careful common-mode and output-range analysis. Input bias current, offset voltage, gain-bandwidth product, and noise are not available in the accessible excerpts and must be confirmed from the datasheet before selecting resistors and setting gain.
Recommandé
Low-Power Audio Preamplifier
OPA234PA can provide two low-power preamplifier channels in audio equipment requiring modest bandwidth rather than the specialized performance of a dedicated high-voltage audio amplifier. The dual configuration suits stereo line-level conditioning, buffering, or tone-control stages. Operation from +5 V is useful in compact audio products, and ±15 V operation supports higher-swing laboratory equipment. Designers should verify output swing, input bias current, slew rate, and noise against the audio bandwidth before selecting the device for high-fidelity applications.
Recommandé
Communications Interface Buffering
OPA234PA is applicable to low-speed communications interfaces that need buffering, gain, or impedance isolation. Its dual architecture allows one amplifier to condition a transmit-side signal and the other to buffer a receive-side or feedback path. The low quiescent current benefits battery-powered communications equipment, while operation from +2.7 V, +5 V, or ±15 V supports several system architectures. The amplifier should be used only where its input common-mode range, output swing, bandwidth, slew rate, and stability characteristics satisfy the signal amplitude and edge-rate requirements.
Recommandé
Precision Voltage Reference Buffer
OPA234PA can buffer a low-current reference node when the source impedance is high or the load requires more drive than the reference can provide directly. Two amplifier sections may be used for reference buffering and auxiliary signal conditioning. The precision and low-power positioning of the OPA234 family fits measurement systems operating from +2.7 V, +5 V, or ±15 V. Before using it in a reference path, confirm input bias current, offset voltage, noise, output current capability, and stability from the manufacturer’s electrical-characteristics table because those specifications are not listed in the accessible product excerpts.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour OPA234PA — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Notes de conception
Place the supply-decoupling network close to the OPA234PA pins and use short, low-inductance connections between the capacitor and the device. Account for the documented 250 µA quiescent current per amplifier when sizing the supply budget, and include additional current for the output load and any bias paths. In single-supply designs, verify that signal excursions remain within the amplifier’s input common-mode and output-swing limits.
Do not treat every OPA234-family device as a drop-in substitute for OPA234PA. The PA suffix is associated with an 8-pin PDIP package, whereas other listed family options may use surface-mount packages. Confirm pin numbering and functions, input and output common-mode ranges, gain-bandwidth product, slew rate, offset voltage, and stability before replacing a part or revising a PCB.
Route the two amplifier channels to minimize coupling between high-impedance inputs, supply returns, and sensitive output nodes. Keep feedback components close to their associated amplifier pins, maintain a compact ground return, and avoid routing input traces beneath noisy supply or digital paths. When using one channel, configure the unused amplifier in the stable manner specified by the manufacturer rather than leaving its inputs floating.
Informations de conformité
No explicit compliance declarations were identified for OPA234PA in the accessible manufacturer or distributor excerpts.