OPA2681N - 280MHz Dual Current Feedback Op Amp | Texas Instruments
Référence : OPA2681N ✓ ActifOPA2681N Présentation
An operational amplifier is an analog signal-processing IC that uses high-gain feedback to amplify or shape voltage signals. A voltage-feedback amplifier uses feedback to control a differential-input error voltage, while a current-feedback amplifier senses current through its feedback network. The current-feedback approach is associated with high-speed amplification because it can maintain useful large-signal bandwidth as gain increases. The OPA2681N therefore belongs to the broad operational-amplifier and signal-conditioning hierarchy rather than to precision low-noise or micropower regulator families.
The principal verified characteristics are its dual-amplifier configuration, 280 MHz stated bandwidth, current-feedback topology, and 14-SOIC package. The package provides a compact surface-mount implementation for high-speed analog and mixed-signal circuits. Because this product is intended for wideband use, PCB layout is as important as the nominal bandwidth: short feedback paths, controlled ground return paths, appropriate decoupling, and minimization of parasitic capacitance help preserve signal integrity. The two amplifier channels should be evaluated for channel matching when the application depends on common-mode rejection, gain consistency, or differential signal cancellation.
Typical uses include active filters, video and communications signal conditioning, waveform-generation and measurement circuits, communications transceivers, analog instrumentation, and active impedance or termination networks. Current-feedback amplifiers are particularly useful when the signal has meaningful high-frequency content and when the required closed-loop gain is higher than the bandwidth divided by a conservative gain-bandwidth assumption. The circuit designer must select resistor values according to the manufacturer’s recommended feedback network rather than treating the amplifier as an ideal voltage-feedback device.
For a new design, begin with the manufacturer datasheet, verify the exact pin functions and disable behavior, and reproduce the recommended power-supply decoupling and feedback topology. The disable function should be checked against the system power-management requirements. When replacing an existing amplifier, verify package pinout, supply range, input and output headroom, output-current capability, disable logic, and stability with the actual load before treating it as a drop-in substitution.
This page combines the verified OPA2681N identity, package, topology, and bandwidth information with application guidance, comparison structure, and replacement-selection considerations. It is designed to help engineers move from part identification to circuit-level validation without relying solely on a catalog listing or an unstructured component-search result.
Alternatives de remplacement direct pour OPA2681N — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
OPA2681N-1
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
OPA2681N/2K5
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
OPA2681N Valeurs maximales et caractéristiques électriques
| Manufacturer | Texas Instruments |
| MPN | OPA2681N |
| Device Type | Operational Amplifier |
| Amplifier Configuration | Dual |
| Topologie | Current Feedback |
| Stated Bandwidth | 280 MHz |
| Boîtier | 14-SOIC |
| Number of Circuits | 2 circuits |
| Type de montage | Surface Mount |
| Product Description | Current Feedback Amplifier 2 Circuit 14-SOIC |
| Series | SpeedPlus |
| Disable Function | Yes |
Guide de configuration des broches du OPA2681N 14-soic
Configuration des broches du OPA2681N (boîtier 14-soic). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour OPA2681N.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
OPA2681N convient pour 6 applications: Wideband Active Filters, Communications Signal Conditioning, Video Amplification, Instrumentation Signal Conditioning, Active Termination Networks, Precision Waveform Generation.
Wideband Active Filters
OPA2681N fits high-speed active-filter stages because its stated 280 MHz bandwidth and current-feedback architecture support wideband signal shaping. Each channel can implement a filtering section when the circuit operates at frequencies where the selected gain, feedback resistor, source impedance, and load are compatible with the manufacturer’s stability guidance. The practical benefit is the availability of two amplifiers in one 14-SOIC package, reducing board area and supporting channel matching. However, high-speed filter design requires short PCB traces, grounded return paths, stable component tolerances, and parasitics-aware simulation. Verify the complete frequency response on the assembled board because the nominal 280 MHz device bandwidth does not by itself determine the usable filter bandwidth.
Recommandé
Communications Signal Conditioning
OPA2681N is suitable for communications signal conditioning, gain adjustment, and impedance-conversion stages that require a wideband analog amplifier. The 280 MHz stated bandwidth allows the device to process signals well beyond audio-frequency limits, while the current-feedback topology is intended to maintain useful large-signal behavior at higher closed-loop gains. The dual 14-SOIC package supports two related channels in compact communication equipment. Designers must choose feedback values from the manufacturer’s guidance and control trace length, supply return paths, and output loading. Confirm input/output headroom and disable-state requirements against the communications link before releasing the circuit.
Recommandé
Video Amplification
OPA2681N can serve in video and composite-signal amplification paths where a high-speed dual amplifier is useful for gain adjustment, termination, or active filtering. Its stated 280 MHz bandwidth is the principal reason to prefer this device over a low-speed general-purpose op amp, while the two-circuit package can implement matched processing channels. The design must preserve signal integrity through short traces, a continuous ground reference, and decoupling placed close to the supply pins. Because video systems can be sensitive to gain accuracy, overshoot, and channel mismatch, evaluate the complete source and load network and compare the measured output against the required video bandwidth before production.
Recommandé
Instrumentation Signal Conditioning
OPA2681N is useful in instrumentation front ends when the measured signal requires wideband amplification ahead of sampling, detection, or comparison. The 280 MHz stated bandwidth can support higher-frequency signals than conventional precision op amps, and the dual configuration can process two related channels. Current-feedback operation requires feedback-network selection according to the manufacturer’s recommendations, and the final error budget must include offset, noise, bias current, output swing, and load-dependent behavior. For low-level measurement channels, first confirm that the wideband architecture does not compromise the required accuracy, then validate noise, settling, and common-mode performance on the target board.
Recommandé
Active Termination Networks
OPA2681N can be used in active termination or impedance-conversion networks for high-speed lines and test equipment. Its current-feedback architecture and stated 280 MHz bandwidth allow it to implement feedback-controlled termination rather than relying only on passive resistors. This can improve signal integrity when the source and load impedances are poorly matched, particularly in instrumentation and communications equipment. The two amplifier channels in a 14-SOIC package provide compact implementation for paired or complementary networks. Validate output-current capability, output-voltage headroom, and loop stability against the terminated line. Keep the feedback trace short and place any compensation or termination components according to the manufacturer’s recommended layouts.
Recommandé
Precision Waveform Generation
OPA2681N fits precision waveform-generation buffers when the required output bandwidth approaches the capabilities of general-purpose amplifiers. Its stated 280 MHz bandwidth supports fast edges and wideband waveform fidelity, while current feedback makes the device appropriate for the high-speed gain stages often used in arbitrary-waveform and pulse-generation systems. The dual package allows two buffered outputs to be driven by separate stages. Designers should select resistor values and gain settings from the manufacturer’s recommended feedback network, then verify output swing and load stability. High-frequency PCB routing, grounding, and decoupling are critical because otherwise the practical waveform may be limited by the board rather than the amplifier.
Recommandé
Données de référence d'ingénierie pour OPA2681N — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | OPA2681N-1 | OPA2681N/2K5 |
|---|---|---|---|
| Manufacturer | Texas Instruments | Texas Instruments / Burr Brown | Texas Instruments |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-SOIC | 14-SOIC - same | 14-SOIC - same |
| Amplifier Configuration | Dual | Dual | Dual |
| Topology | Current Feedback | Current Feedback | Current Feedback |
| Stated Bandwidth | 280 MHz | 280 MHz | 280 MHz |
| Series | SpeedPlus | SpeedPlus | SpeedPlus |
| Disable Function | Yes | Yes | Yes |
Principaux différenciateurs
- Same-package dual current-feedback replacement options (vs OPA2681N-1)
- Documented 280 MHz wideband capability (vs OPA2681N/2K5)
- Two high-speed amplifiers in one package (vs OPA2681N-1)
Notes de conception
Keep input, output, and feedback paths short and continuous because the 280 MHz stated bandwidth makes PCB inductance and capacitance significant. Use a solid ground reference, avoid routing high-speed signals over split plane boundaries, and place decoupling capacitors close to the relevant supply pins. Match trace geometry between the two channels when differential or common-mode cancellation depends on channel consistency.
Do not choose feedback resistors using a generic voltage-feedback design rule. Current-feedback amplifiers require the manufacturer’s recommended feedback-network values and gain-dependent stability analysis. Confirm the final circuit with the intended source impedance, load capacitance, output current, and supply voltage. A PCB that appears correct at low frequency may become unstable when the amplifier drives a long cable, capacitive load, or high-speed probe.
Decouple each supply connection close to the device and use the manufacturer’s recommended power-supply arrangement. Because OPA2681N is a high-speed amplifier, supply-impedance interaction can affect output behavior and stability. Provide local ground return paths for output-current transients rather than relying on distant plane connections. Validate the disable function and power-up sequence to prevent uncontrolled output conditions in the final system.
Informations de conformité
Compliance attributes require confirmation from the manufacturer product page or the current manufacturer declaration. The supplied product listings identify the part, topology, bandwidth, and package but do not explicitly state the required compliance results.