P1013NSE2HFB557 - QorIQ 32-Bit Power Arch SoC 800MHz | NXP/Freescale
Référence : P1013NSE2HFB557 ✓ ActifP1013NSE2HFB557 Présentation
A QorIQ communications SoC (System-on-Chip) is a highly-integrated processor that combines one or more CPU cores, high-speed serial interfaces, packet processing engines, and security accelerators on a single die. Within the broader processor taxonomy, QorIQ SoCs sit between general-purpose microcontrollers and high-end multicore networking processors, optimized for deterministic throughput on packet data while retaining Linux/Power-Architecture software ecosystem compatibility. They are widely deployed in wired/wireless access equipment, industrial control, and military/aerospace embedded platforms.
The P1013NSE2HFB557 provides a single 32-bit Power Architecture e500 core with MMU, dual 32-bit DDR controllers supporting DDR2/DDR3 memory, three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs), a security engine (SEC 4.0) for encryption acceleration, and a wide array of high-speed serial interfaces. The integrated QUICC Engine technology simplifies development of multi-protocol applications. The SoC targets extended-temperature and industrial-grade reliability with a robust set of peripherals including USB 2.0, PCIe, SPI, I2C, and UART controllers.
Architecturally, the device combines a high-performance superscalar e500 core with hardware-based pattern matching, encryption accelerators, and DMA engines, freeing the CPU from I/O housekeeping. The combination of low power consumption, hardware virtualization support, and integrated GbE switch fabric makes it attractive for fanless industrial gateways, factory automation controllers, and secure networking appliances. The platform supports standard Linux distributions and VxWorks/RTOS environments.
Typical applications include industrial Ethernet switches and gateways, factory automation controllers, secure routers and firewalls, smart-grid and substation communication equipment, defense and aerospace networking gear, automotive telematics and infotainment modules, and medical imaging or diagnostic data acquisition systems requiring deterministic networking throughput with hardware-accelerated cryptography.
When designing with this device, allocate sufficient PCB area for the high-pin-count thermally-enhanced package and follow NXP hardware reference manual recommendations for DDR3 routing, decoupling, and thermal dissipation. Always verify boot configuration, JTAG chain, and SerDes reference clocking per the official reference manual before bringing up a new board.
This page synthesizes distributor pricing, package metadata, and practical design context that complement the official NXP P1013 reference manual and QorIQ P1 product brief, providing engineers a fast decision-ready overview beyond what datasheets alone expose.
Alternatives de remplacement direct pour P1013NSE2HFB557 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
P1014NSE2HFB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
P1025NSE2HFB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
P1010NSE2HFB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
P1013NSE2HFB558
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
P2020NSE2HFB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
P1013NSE2HFB557 Valeurs maximales et caractéristiques électriques
| Series | QorIQ P1 |
| Core Processor | Power Architecture e500 |
| Number of Cores | 1 |
| Core Speed | 800 MHz |
| Architecture | 32-bit |
| Product Type | Microprocessors (SoC) |
| Description | QORIQ, 32 BIT POWER ARCH SOC, 800 |
| Memory Interface | DDR2/DDR3 with 32-bit controllers |
| Ethernet Controllers | 3 x 10/100/1000 Mbps eTSEC |
| Security Engine | SEC 4.0 (crypto acceleration) |
| USB | USB 2.0 |
| PCIe | PCIe interface |
| Serial I/O | SPI, I2C, UART |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant |
| Manufacturer | NXP Semiconductors (formerly Freescale) |
| Boîtier | Surface-mount thermally-enhanced (HBGA family) |
Guide de configuration des broches du P1013NSE2HFB557 surface-mount thermally-enhanced (hbga family)
Configuration des broches du P1013NSE2HFB557 (boîtier surface-mount thermally-enhanced (hbga family)). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour P1013NSE2HFB557.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
P1013NSE2HFB557 convient pour 6 applications: Industrial Ethernet Switches and Gateways, Secure Routers and VPN Appliances, Factory Automation Controllers, Smart Grid and Substation Communication, Defense and Aerospace Embedded Networking, Automotive Telematics and Infotainment Modules.
Industrial Ethernet Switches and Gateways
The P1013NSE2HFB557 is purpose-built for managed industrial switches where deterministic per-packet latency and hardware-isolated networking matter more than raw multi-core throughput. Its three integrated gigabit eTSEC controllers deliver line-rate forwarding on at least three copper or fiber ports without external PHY bridging, while the SEC 4.0 engine offloads AES, 3DES, and IPSec at wire speed - critical for IPsec-protected industrial rings. Combined with the QorIQ P1 platform's long-life-cycle NXP support and industrial temperature grade, it drops directly into factory-floor DIN-rail gateways, protocol-conversion bridges (Profinet/EtherCAT/Ethernet/IP), and substation routers used in IEC 61850 environments.
Recommandé
Secure Routers and VPN Appliances
The P1013NSE2HFB557 is well-matched to small/branch-office VPN routers and secure firewalls where hardware-accelerated crypto and a deterministic Power Architecture core provide predictable throughput under load. Its SEC 4.0 engine handles AES-256-GCM and SHA-2 at line rates that an equivalent ARM Cortex-A application processor typically cannot sustain without thermal throttling. The dual 32-bit DDR2/DDR3 controllers sustain >4 GB/s aggregate memory bandwidth, enough for deep packet inspection buffers and concurrent IPSec tunnels. For SMB edge routers the P1013 is preferable to a low-end ARM SoC because of the SEC engine's maturity in NXP's ecosystem.
Recommandé
Factory Automation Controllers
Within PLCs and machine controllers, the P1013NSE2HFB557 serves as the deterministic networking brain, offloading industrial protocols from a separate MCU. The single e500 core at 800 MHz combined with hardware pattern matching accelerates CIP, PROFINET, and EtherCAT frames with sub-100-microsecond latency, while the PCIe endpoint can interface to a host CPU or to an FPGA for high-speed deterministic I/O expansion. Its industrial-grade temperature range and the QorIQ platform's certified long-term supply align with the 10-15 year lifecycle expected of factory equipment.
Recommandé
Smart Grid and Substation Communication
Substation communication equipment - IEC 61850 IEDs, teleprotection gateways, and PMU aggregators - relies on the P1013NSE2HFB557 because of its deterministic networking, hardware crypto, and proven long-term NXP support. The SEC 4.0 engine handles the authentication and MAC verification required for IEC 62351-6 while the e500 core runs the IEC 61850 stack with predictable timing. The package's extended temperature range and the platform's long-life commitment map cleanly onto the 15-20 year deployment horizon of utility substation equipment.
Recommandé
Defense and Aerospace Embedded Networking
Defense and aerospace programs adopt the P1013NSE2HFB557 because the QorIQ P1 family is widely accepted in safety-critical and avionics-grade design flows, with documentation packages and errata tailored to long-term aerospace programs. The Power Architecture e500 core, combined with hardware virtualization and SEC 4.0 crypto, supports partitioned secure/unsecure workloads on a single SoC - ideal for tactical radios, ground-vehicle networking, and mission-computer auxiliary processors. Its tolerance for extended operating temperature and the platform's mature Linux and VxWorks BSP ecosystem shorten aerospace qualification timelines.
Recommandé
Automotive Telematics and Infotainment Modules
Connected-vehicle telematics and fleet-management gateways leverage the P1013NSE2HFB557 for its three integrated gigabit Ethernet controllers and SEC 4.0 hardware encryption. Within a vehicle the SoC aggregates CAN, LIN, automotive Ethernet, and V2X traffic, runs the telematics stack on Linux, and offloads TLS/IPSec via the SEC engine without consuming core cycles. The platform's automotive-grade variants in the same QorIQ P1 package family enable drop-in migration to AEC-Q-qualified parts for production programs.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour P1013NSE2HFB557 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | P1014NSE2HFB | P1025NSE2HFB | P1010NSE2HFB | P2020NSE2HFB |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | HBGA (thermally-enhanced, QorIQ P1 family) | HBGA (thermally-enhanced, same QorIQ P1 family) - same | HBGA (thermally-enhanced, same QorIQ P1 family) - same | HBGA (thermally-enhanced, same QorIQ P1 family) - same | HBGA (thermally-enhanced, QorIQ P2 family) - drop-in footprint |
| Core Architecture | 32-bit Power Architecture e500 | 32-bit Power Architecture e500 - same | 32-bit Power Architecture e500 - same | 32-bit Power Architecture e500 - same | 32-bit Power Architecture e500 - same |
| Core Count | 1 | 1 | 2 | 1 | 2 |
| Core Speed | 800 MHz | 1.0 GHz | 1.4 GHz (dual-core aggregate) | 667 MHz | 1.2 GHz (dual-core aggregate) |
| Gigabit Ethernet Controllers | 3 x eTSEC | 3 x eTSEC | 3 x eTSEC | 2 x eTSEC | 3 x eTSEC + 10 GbE option |
| Security Engine | SEC 4.0 | SEC 4.0 | SEC 4.0 | SEC 3.0 | SEC 4.0 |
| Target Market | Industrial / Networking / Aerospace | Industrial / Networking / Aerospace | Industrial / Networking / Aerospace | Cost-sensitive industrial | Mid-range networking |
| Unit Price (qty-1, USD, as of 2026-10-17) | 78.40 | 85.60 | 120.00 | 55.00 | 150.00 |
Principaux différenciateurs
- Single-core 800 MHz cost-optimized QorIQ P1 part (vs P1025NSE2HFB)
- Three gigabit Ethernet controllers with SEC 4.0 (vs P1010NSE2HFB)
- Same-family drop-in upgrade path to P1014 (vs P1014NSE2HFB)
Notes de conception
The P1013NSE2HFB557 is supplied in a high-pin-count thermally-enhanced HBGA package. Per NXP's QorIQ P1013 hardware reference manual, maintain a minimum 6-layer PCB stack-up with continuous ground planes under the BGA, and route DDR2/DDR3 traces with matched-length (within +/-25 mil) for byte-lane pairs to avoid signal-integrity issues at 800 MHz. Place bulk decoupling capacitors within 5 mm of the SoC supply balls and follow the reference manual's decoupling table verbatim.
Estimated: at full 800 MHz operation with all three eTSECs active, the P1013NSE2HFB557 dissipates approximately 5-7 W; with a typical HBGA theta-JA of around 15-20 C/W, junction temperature rise above ambient is approximately 75-100 C. Ensure adequate airflow or a heatsink in industrial enclosures with ambient temperatures above 50 C, and validate with the manufacturer's thermal model before finalizing the enclosure layout.
Do not assume all P1013 family variants are pin-compatible: the P1013/P1014/P1010 share the same QorIQ P1 HBGA footprint, but industrial-grade and aerospace-screened variants differ in temperature range and errata. Always cross-check the device's hardware errata document against your reference manual revision, and verify boot configuration (cfg_rcw[1:8] pins) before bringing up new hardware. A common pitfall is mismatching the reference-clock frequency, which silently breaks PCIe link training.
Informations de conformité
RoHS and lead-free confirmed by JLCPCB/LCSC listings as of 2026-10-17. AEC-Q100 not applicable - this is an industrial/aerospace-grade SoC, not an automotive-qualified part; for AEC-Q100 programs, contact NXP for the automotive QorIQ P1 variant.
