NXP Semiconductors

PCA9564D - 400 kHz Parallel-to-I2C Controller | NXP Semiconductors

Référence : PCA9564D ✓ Actif
2.3 V to 3.6 V Vdss 6 mA Id 20-pin SO, 7.50 mm width Package 400 kHz Speed
MOQ : 1 |

PCA9564D Présentation

The NXP Semiconductors PCA9564D is a parallel-bus to I2C-bus controller with a 2.3 V to 3.6 V operating supply range and a 400 kHz I2C interface in a 20-pin SO package. It converts data presented by an 8-bit parallel host interface into serial I2C transactions, allowing a microcontroller or processor with limited I2C capability to communicate with serial devices.

A parallel-to-I2C bus controller is an interface IC that bridges two different digital communication methods. The parallel side accepts byte-oriented data and associated control signals, while the I2C side generates the clock and serial data required by an I2C bus. In the broader semiconductor hierarchy, the PCA9564D belongs to the interface-controller class, specifically parallel-bus-to-I2C-bus conversion.

The verified device information identifies a controller type of parallel bus to I2C bus, a 2.3 V minimum supply voltage, a 3.6 V maximum supply voltage, and approximately 6 mA supply current. The associated 20-pin SO package occupies a 7.50 mm body width. These characteristics make the device applicable to embedded control systems that need an efficient bridge between a parallel CPU or programmable-logic interface and a 400 kHz I2C peripheral bus.

The 400 kHz bus capability provides faster serial transfer than the traditional 100 kHz I2C rate while retaining compatibility with the established two-wire interface. The device can therefore reduce the number of serial transactions required when communicating with slower I2C peripherals, provided the selected peripheral supports fast-mode operation and the complete bus meets the required timing and rise-time characteristics.

Typical uses include industrial control systems, automated test equipment, programmable-logic controllers, embedded instruments, and communication peripherals. In each case, the controller separates the host-side byte-oriented data path from the serial peripheral bus, simplifying firmware and reducing the number of host I2C transactions when both sides are controlled by the same system.

Designers should confirm the exact logical pin assignments, address configuration, and electrical characteristics in the manufacturer datasheet before laying out the PCB. The 2.3 V to 3.6 V supply range requires compatible pull-ups and signal levels across the entire parallel and I2C interface. PCB placement should minimize parallel-bus switching noise and provide a clean return path between the controller, supply network, and attached I2C devices.

This page consolidates the verified device specifications, ordering variants, drop-in comparison, and practical interface-design guidance into one engineering-focused reference. It also distinguishes confirmed electrical facts from parameters that still require confirmation from the complete manufacturer datasheet before a new design is released to production.

Alternatives de remplacement direct pour PCA9564D — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec PCA9564D (même facteur de forme et même empreinte) — différant par Package Type.

NXP Semiconductors
Package Type: SSOP-24
Comparer avec PCA9564D →
NXP Semiconductors
Package Type: SSOP-24
Comparer avec PCA9564D →

PCA9564D,118

✅ Remplacement direct
📦 20-SO
Same PCA9564D function, terminal arrangement, 2.3 V to 3.6 V supply range, and 20-SO package; ordering suffix differs

📋 Alternative de référence (hors catalogue)

PCA9564D Spécifications

Controller Type Parallel bus to I2C bus controller
Parallel Interface 8-bit parallel bus
Serial Interface I2C bus
Supply Voltage Range 2.3 V to 3.6 V
Nominal Supply Voltage 2.5 V or 3.3 V
Courant d'alimentation 6 mA
Maximum I2C Bus Frequency 400 kHz
Boîtier 20-pin SO, 7.50 mm width
Package Type SOIC-20
Type de montage Surface mount
Nombre de broches 20
Parallel Data Width 8 bits

Guide de configuration des broches du PCA9564D soic-20

Configuration des broches du PCA9564D (boîtier soic-20). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.

Schéma de brochage du boîtier soic-20 pour le PCA9564D

Aucune donnée de brochage détaillée disponible pour PCA9564D.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

PCA9564D convient pour 6 applications: Industrial Control Interfaces, Programmable Logic Controller Peripherals, Automated Test Equipment, Embedded Instrumentation, Communication Peripheral Expansion, Data Acquisition Modules.

🏭

Industrial Control Interfaces

The PCA9564D fits industrial controllers that expose an 8-bit parallel register interface but must operate I2C sensors, memory devices, or communications peripherals. Its 2.3 V to 3.6 V supply range supports 3.3 V control systems, while the 400 kHz I2C rate can reduce transaction time relative to a 100 kHz bus. The controller keeps serial-bus activity outside the host firmware’s parallel data path, simplifying register mapping. Designers should match all interface levels and confirm the operating-temperature grade before deployment.

🔧

Programmable Logic Controller Peripherals

The PCA9564D is useful when a programmable-logic controller needs a structured parallel interface to an I2C peripheral bus. The 8-bit parallel side accommodates byte-oriented control data, while the controller handles conversion to the two-wire I2C format at up to 400 kHz. This arrangement can shorten design time in laboratory and industrial automation equipment. Confirm address behavior, control-signal timing, pull-up values, and package-level pin assignments in the manufacturer datasheet before fixing the logic design.

📡

Automated Test Equipment

The PCA9564D can bridge test-vector or configuration registers in a parallel-format instrument to I2C-controlled DUT support devices. Its 2.5 V and 3.3 V operating points suit modern low-voltage test electronics, while the 400 kHz bus rate supports faster configuration transfers. Keeping the I2C transaction handling in dedicated hardware can make instrument firmware more predictable. Signal-integrity checks should include pull-up selection, bus capacitance, clock rise time, and isolation boundaries.

📺

Embedded Instrumentation

The PCA9564D suits embedded instruments whose control processor presents commands through an 8-bit parallel bus but accesses calibration memories, sensors, or display controllers through I2C. The dedicated converter reduces repeated host-side bit manipulation and supports I2C operation up to 400 kHz. With a 2.3 V to 3.6 V supply range and approximately 6 mA supply current, it can fit into compact 3.3 V instrument electronics. Verify timing margins under the worst-case bus capacitance and operating temperature.

🌐

Communication Peripheral Expansion

The PCA9564D can provide a parallel-domain front end for I2C communication peripherals in compact embedded systems. This is especially helpful when the principal processor has limited available I2C pins or when byte-oriented legacy logic must coexist with modern serial peripherals. The 400 kHz bus capability improves transfer efficiency, while the 20-pin SO package supports conventional surface-mount assembly. Verify the complete pinout, address-selection method, and electrical timing before replacing an existing parallel-to-serial bridge.

🖥️

Data Acquisition Modules

The PCA9564D can connect a parallel control section of a data-acquisition module to I2C sensor front ends, configuration DACs, or external memory. The controller’s 2.3 V to 3.6 V operating range aligns with 3.3 V acquisition electronics, and the 400 kHz I2C rate supports timely configuration and monitoring. It is particularly useful when acquisition channels are managed through byte-oriented logic. Designers should account for pull-up rise time, shared-bus loading, and separate analog and digital grounding in the PCB layout.

Récapitulatif des produits recommandés

PCA9564D,118 Same-controller ordering option Utilisé dans : Industrial Control Interfaces, Programmable Logic Controller Peripherals, Automated Test Equipment, Embedded Instrumentation, Communication Peripheral Expansion, Data Acquisition Modules PCA9564D,112 Same-controller ordering option Utilisé dans : Industrial Control Interfaces, Automated Test Equipment, Communication Peripheral Expansion
What is the PCA9564D?
The PCA9564D is an NXP Semiconductors parallel-bus to I2C-bus controller packaged in a 20-pin SO device. According to the manufacturer datasheet, it is intended to bridge an 8-bit parallel data interface with an I2C peripheral bus. The device operates from 2.3 V to 3.6 V and supports an I2C bus frequency of up to 400 kHz, making it useful where a host processor lacks convenient or sufficient I2C resources.
What is the operating voltage of PCA9564D?
The PCA9564D operates from 2.3 V to 3.6 V, with 2.5 V and 3.3 V identified as the principal operating points in the device documentation. The same voltage domain must be used for the parallel interface, I2C pull-ups, and associated digital circuitry. According to the manufacturer datasheet, the device consumes approximately 6 mA of supply current, which should be included in power-budget calculations.
What is the I2C bus frequency of PCA9564D?
The PCA9564D supports an I2C bus frequency of up to 400 kHz. This is the fast-mode operating rate identified for the device and can reduce transaction time compared with a 100 kHz bus. According to the manufacturer datasheet, actual bus operation also depends on peripheral support, pull-up resistance, capacitance, clock stretching, and the rise-time limits of the complete PCB.
Where can I download the PCA9564D datasheet PDF?
The PCA9564D datasheet PDF can be accessed through the documented datasheet link on this page, while the manufacturer product documentation should be the authority for design release. The document describes a parallel-bus to I2C-bus controller with a 2.3 V to 3.6 V supply range, approximately 6 mA supply current, 400 kHz I2C operation, and a 20-pin SO package. Use its pin-description table when assigning PCB nets.
Where is the PCA9564D pinout located?
The PCA9564D pin assignment and package drawing are located in the manufacturer datasheet, which this page references through its datasheet link. The device uses a 20-pin SO package, but an individual pin-name list is not published in the concise device record. Use the datasheet pin-description table to identify power, ground, parallel-bus, control, clock, and serial-data connections before creating a PCB footprint.
Where can I buy PCA9564D online?
The PCA9564D can be requested through the Request a Quote form on this page, which is the appropriate route for current commercial availability and shipment requirements. The documented manufacturer variants include PCA9564D,112 and PCA9564D,118, both associated with a 20-pin SO package. Share the required quantity, date code, and target shipment location with the supplier to obtain an accurate quotation.
What is the price of PCA9564D?
Current PCA9564D pricing is best obtained through the Request a Quote form on this page because commercial conditions can change with quantity, packaging, date code, and availability. The verified product records identify the relevant ordering variants but do not present a qualifying exact-MPN quantity-break table. Submit the required quantity and packaging preference to receive a current quotation without relying on an outdated or incomplete price.
What is the lead time for PCA9564D?
The current PCA9564D lead time should be confirmed through the Request a Quote form on this page using the selected ordering code, quantity, and desired delivery date. Distributor records confirm active sourcing of PCA9564D,112 and PCA9564D,118, but they do not establish a fixed lead time for every quantity. Providing a forecast and required ship date allows the supplier to check the relevant production and inventory status.
Is PCA9564D in stock?
PCA9564D availability varies by ordering code, quantity, packaging, and date code. The Request a Quote form on this page is the reliable route for checking the current stock position and the associated shipment plan. The documented variants are PCA9564D,112 and PCA9564D,118 in a 20-pin SO package; specify the exact suffix required by the BOM when requesting availability confirmation.
What can replace PCA9564D?
PCA9564D,118 is the documented same-package drop-in candidate because it retains the PCA9564D function, terminal arrangement, and 20-pin SO package. It should be treated as an ordering-code alternative rather than a functional upgrade. A broader replacement cannot be confirmed from the available cross-reference material, so validate the complete pin list, I2C timing, address behavior, and supply requirements before approving any substitute.
Is PCA9564D,118 the same as PCA9564D?
PCA9564D,118 is functionally and electrically a source-identifiable ordering option of the PCA9564D in the same 20-pin SO package. The comparison information identifies consistent terminals, package, and principal performance characteristics. The suffix distinguishes the orderable packaging or delivery form rather than introducing a different controller function, so an existing PCA9564D design can generally use PCA9564D,118 without PCB changes.
When should I choose PCA9564D instead of a software I2C implementation?
Choose the PCA9564D when the host interface is naturally parallel and the design benefits from dedicated I2C transaction handling at up to 400 kHz. The hardware bridge can reduce host-side I2C driver complexity and separate serial peripheral communication from the parallel data path. It is less attractive when the host already has plentiful I2C controller resources, because a software implementation may then avoid the extra IC and associated routing requirements.
Is PCA9564D suitable for industrial control systems?
The PCA9564D is suitable for many 2.5 V or 3.3 V industrial embedded-control systems that need an 8-bit parallel host interface to control I2C peripherals. Its 400 kHz bus rate and approximately 6 mA supply current are appropriate for many embedded subsystems. Final suitability depends on the industrial temperature grade, EMC requirements, isolation strategy, and peripheral specifications, which must be confirmed from the complete datasheet.
What is the best cross-brand equivalent for PCA9564D?
No cross-brand drop-in equivalent is established by the available cross-reference information for the PCA9564D. The closest documented candidates are NXP ordering variants, while the comparison with PCA9555DB indicates a different 24-pin SSOP package and is therefore not pin compatible. Do not substitute a cross-brand controller solely from generic interface similarities; require a documented 20-pin SO footprint, matching I2C timing, address scheme, and control logic.
What are the key specifications of PCA9564D that engineers should know?
The key PCA9564D specifications are its parallel-bus to I2C-bus controller function, 2.3 V to 3.6 V supply range, approximately 6 mA supply current, 400 kHz I2C operation, and 20-pin SO package. According to the manufacturer datasheet, the device bridges an 8-bit parallel interface to a serial I2C bus. These are the principal values to use for architecture selection, logic-level matching, PCB planning, and bus timing review.

Données de référence d'ingénierie pour PCA9564D — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose the PCA9564D when an embedded system needs a dedicated bridge from an 8-bit parallel host interface to an I2C peripheral bus. Its 400 kHz I2C capability is valuable when configuration or monitoring transfers must complete faster than on a 100 kHz bus, while the 2.3 V to 3.6 V supply range fits low-voltage 3.3 V equipment. PCA9564D,118 is the appropriate drop-in ordering option when the same 20-SO device, terminal arrangement, and electrical behavior are required under a fully specified purchasing code. Do not select PCA9555DB as a direct replacement because it uses a different 24-pin SSOP package. A cross-brand substitute should be chosen only after its footprint, parallel control signals, I2C timing, address configuration, supply pins, and operating-temperature limits have been checked against the manufacturer datasheet.

Comparaison avec les alternatives

Paramètre Ce produit PCA9564D,118
Brand NXP Semiconductors NXP Semiconductors
Package 20-SO, 7.50 mm width 20-SO
Controller Type Parallel bus to I2C bus controller Parallel bus to I2C bus controller
Supply Voltage Range 2.3 V to 3.6 V 2.3 V to 3.6 V
Supply Current 6 mA 6 mA
I2C Bus Frequency 400 kHz 400 kHz
Parallel Data Width 8 bits 8 bits
Interface Parallel and I2C Parallel and I2C
Ordering Suffix PCA9564D ,118 ordering suffix

Principaux différenciateurs

  • Direct 8-bit parallel-to-I2C conversion (vs PCA9564D,118)
  • Fast-mode I2C operation (vs PCA9564D,118)
  • Low-voltage system compatibility (vs PCA9564D,118)

Notes de conception

Use the manufacturer datasheet pin-description table when routing the 20-pin SO footprint and assign the I2C pull-up resistors directly to the SDA and SCL pins. Keep parallel-bus routing away from the serial clock and data nets, and provide a continuous ground reference beneath the device. The listed 7.50 mm package width must also be reconciled with the manufacturer land pattern before releasing artwork.

Select I2C pull-up resistance from the bus capacitance, clock rise-time requirement, and sink-current limit rather than using a fixed value without calculation. A 400 kHz bus has less timing margin than a 100 kHz bus. Confirm that every connected peripheral supports the selected rate, and account for clock stretching and additional capacitance introduced by long traces or test points.

Do not substitute a controller merely because it supports I2C and uses a 20-pin package. Pin-to-pin replacement requires compatible supply pins, ground connections, parallel-bus control signals, I2C behavior, address configuration, and electrical timing. PCA9555DB is not a drop-in option because it uses a different 24-pin SSOP package. Verify the full manufacturer pinout and application timing before approving any alternate source.

Design the 2.3 V to 3.6 V supply rail with local decoupling close to the device and account for approximately 6 mA supply current in the system budget. Avoid placing the I2C pull-up return current through sensitive analog ground paths. If the parallel host interface crosses voltage domains, use properly rated level-shifting or isolation components rather than relying on pull-ups alone.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The concise device records do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is recorded as not applicable because this is a general-purpose interface controller rather than an automotive-qualified device claim.

Recherches associées

PCA9564D datasheet PCA9564D datasheet pdf PCA9564D pinout PCA9564D specifications PCA9564D equivalent PCA9564D replacement PCA9564D cross reference PCA9564D 20-SO footprint PCA9564D 400 kHz I2C NXP PCA9564D PCA9564D price PCA9564D stock

Composants & termes associés

NXP Semiconductors PCA9564D PCA9564D,112 PCA9564D,118 PCA9555DB Parallel bus to I2C bus controller Parallel interface I2C I2C bus controller Interface IC 8-bit parallel bus 400 kHz I2C 2.3 V to 3.6 V supply 6 mA supply current 20-SO package SOIC-20 Surface-mount package Industrial control Programmable-logic controller Automated test equipment Embedded instrumentation Data acquisition I2C pull-up resistor SDA SCL
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ