PCA9564D - 400 kHz Parallel-to-I2C Controller | NXP Semiconductors
N.º da peça: PCA9564D ✓ AtivoPCA9564D Visão geral
A parallel-to-I2C bus controller is an interface IC that bridges two different digital communication methods. The parallel side accepts byte-oriented data and associated control signals, while the I2C side generates the clock and serial data required by an I2C bus. In the broader semiconductor hierarchy, the PCA9564D belongs to the interface-controller class, specifically parallel-bus-to-I2C-bus conversion.
The verified device information identifies a controller type of parallel bus to I2C bus, a 2.3 V minimum supply voltage, a 3.6 V maximum supply voltage, and approximately 6 mA supply current. The associated 20-pin SO package occupies a 7.50 mm body width. These characteristics make the device applicable to embedded control systems that need an efficient bridge between a parallel CPU or programmable-logic interface and a 400 kHz I2C peripheral bus.
The 400 kHz bus capability provides faster serial transfer than the traditional 100 kHz I2C rate while retaining compatibility with the established two-wire interface. The device can therefore reduce the number of serial transactions required when communicating with slower I2C peripherals, provided the selected peripheral supports fast-mode operation and the complete bus meets the required timing and rise-time characteristics.
Typical uses include industrial control systems, automated test equipment, programmable-logic controllers, embedded instruments, and communication peripherals. In each case, the controller separates the host-side byte-oriented data path from the serial peripheral bus, simplifying firmware and reducing the number of host I2C transactions when both sides are controlled by the same system.
Designers should confirm the exact logical pin assignments, address configuration, and electrical characteristics in the manufacturer datasheet before laying out the PCB. The 2.3 V to 3.6 V supply range requires compatible pull-ups and signal levels across the entire parallel and I2C interface. PCB placement should minimize parallel-bus switching noise and provide a clean return path between the controller, supply network, and attached I2C devices.
This page consolidates the verified device specifications, ordering variants, drop-in comparison, and practical interface-design guidance into one engineering-focused reference. It also distinguishes confirmed electrical facts from parameters that still require confirmation from the complete manufacturer datasheet before a new design is released to production.
Alternativas drop-in para PCA9564D — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PCA9564D (mesmo formato e footprint) — diferindo em Package Type.
PCA9564D,118
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PCA9564D Especificações
| Controller Type | Parallel bus to I2C bus controller |
| Parallel Interface | 8-bit parallel bus |
| Serial Interface | I2C bus |
| Supply Voltage Range | 2.3 V to 3.6 V |
| Nominal Supply Voltage | 2.5 V or 3.3 V |
| Corrente de alimentação | 6 mA |
| Maximum I2C Bus Frequency | 400 kHz |
| Encapsulamento | 20-pin SO, 7.50 mm width |
| Package Type | SOIC-20 |
| Tipo de montagem | Surface mount |
| Número de pinos | 20 |
| Parallel Data Width | 8 bits |
Guia de Configuração de Pinos do PCA9564D soic-20
Configuração de pinos para PCA9564D (pacote soic-20). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para PCA9564D.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
PCA9564D é adequado para 6 aplicaçãos: Industrial Control Interfaces, Programmable Logic Controller Peripherals, Automated Test Equipment, Embedded Instrumentation, Communication Peripheral Expansion, Data Acquisition Modules.
Industrial Control Interfaces
The PCA9564D fits industrial controllers that expose an 8-bit parallel register interface but must operate I2C sensors, memory devices, or communications peripherals. Its 2.3 V to 3.6 V supply range supports 3.3 V control systems, while the 400 kHz I2C rate can reduce transaction time relative to a 100 kHz bus. The controller keeps serial-bus activity outside the host firmware’s parallel data path, simplifying register mapping. Designers should match all interface levels and confirm the operating-temperature grade before deployment.
Recomendado
Programmable Logic Controller Peripherals
The PCA9564D is useful when a programmable-logic controller needs a structured parallel interface to an I2C peripheral bus. The 8-bit parallel side accommodates byte-oriented control data, while the controller handles conversion to the two-wire I2C format at up to 400 kHz. This arrangement can shorten design time in laboratory and industrial automation equipment. Confirm address behavior, control-signal timing, pull-up values, and package-level pin assignments in the manufacturer datasheet before fixing the logic design.
Recomendado
Automated Test Equipment
The PCA9564D can bridge test-vector or configuration registers in a parallel-format instrument to I2C-controlled DUT support devices. Its 2.5 V and 3.3 V operating points suit modern low-voltage test electronics, while the 400 kHz bus rate supports faster configuration transfers. Keeping the I2C transaction handling in dedicated hardware can make instrument firmware more predictable. Signal-integrity checks should include pull-up selection, bus capacitance, clock rise time, and isolation boundaries.
Recomendado
Embedded Instrumentation
The PCA9564D suits embedded instruments whose control processor presents commands through an 8-bit parallel bus but accesses calibration memories, sensors, or display controllers through I2C. The dedicated converter reduces repeated host-side bit manipulation and supports I2C operation up to 400 kHz. With a 2.3 V to 3.6 V supply range and approximately 6 mA supply current, it can fit into compact 3.3 V instrument electronics. Verify timing margins under the worst-case bus capacitance and operating temperature.
Recomendado
Communication Peripheral Expansion
The PCA9564D can provide a parallel-domain front end for I2C communication peripherals in compact embedded systems. This is especially helpful when the principal processor has limited available I2C pins or when byte-oriented legacy logic must coexist with modern serial peripherals. The 400 kHz bus capability improves transfer efficiency, while the 20-pin SO package supports conventional surface-mount assembly. Verify the complete pinout, address-selection method, and electrical timing before replacing an existing parallel-to-serial bridge.
Recomendado
Data Acquisition Modules
The PCA9564D can connect a parallel control section of a data-acquisition module to I2C sensor front ends, configuration DACs, or external memory. The controller’s 2.3 V to 3.6 V operating range aligns with 3.3 V acquisition electronics, and the 400 kHz I2C rate supports timely configuration and monitoring. It is particularly useful when acquisition channels are managed through byte-oriented logic. Designers should account for pull-up rise time, shared-bus loading, and separate analog and digital grounding in the PCB layout.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PCA9564D — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PCA9564D,118 |
|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors |
| Package | 20-SO, 7.50 mm width | 20-SO |
| Controller Type | Parallel bus to I2C bus controller | Parallel bus to I2C bus controller |
| Supply Voltage Range | 2.3 V to 3.6 V | 2.3 V to 3.6 V |
| Supply Current | 6 mA | 6 mA |
| I2C Bus Frequency | 400 kHz | 400 kHz |
| Parallel Data Width | 8 bits | 8 bits |
| Interface | Parallel and I2C | Parallel and I2C |
| Ordering Suffix | PCA9564D | ,118 ordering suffix |
Principais diferenciais
- Direct 8-bit parallel-to-I2C conversion (vs PCA9564D,118)
- Fast-mode I2C operation (vs PCA9564D,118)
- Low-voltage system compatibility (vs PCA9564D,118)
Notas de projeto
Use the manufacturer datasheet pin-description table when routing the 20-pin SO footprint and assign the I2C pull-up resistors directly to the SDA and SCL pins. Keep parallel-bus routing away from the serial clock and data nets, and provide a continuous ground reference beneath the device. The listed 7.50 mm package width must also be reconciled with the manufacturer land pattern before releasing artwork.
Select I2C pull-up resistance from the bus capacitance, clock rise-time requirement, and sink-current limit rather than using a fixed value without calculation. A 400 kHz bus has less timing margin than a 100 kHz bus. Confirm that every connected peripheral supports the selected rate, and account for clock stretching and additional capacitance introduced by long traces or test points.
Do not substitute a controller merely because it supports I2C and uses a 20-pin package. Pin-to-pin replacement requires compatible supply pins, ground connections, parallel-bus control signals, I2C behavior, address configuration, and electrical timing. PCA9555DB is not a drop-in option because it uses a different 24-pin SSOP package. Verify the full manufacturer pinout and application timing before approving any alternate source.
Design the 2.3 V to 3.6 V supply rail with local decoupling close to the device and account for approximately 6 mA supply current in the system budget. Avoid placing the I2C pull-up return current through sensitive analog ground paths. If the parallel host interface crosses voltage domains, use properly rated level-shifting or isolation components rather than relying on pull-ups alone.
Informações de conformidade
The concise device records do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is recorded as not applicable because this is a general-purpose interface controller rather than an automotive-qualified device claim.