PCA9621D - 8-Bit 65mA I/O Expander | NXP | LED Drive
Référence : PCA9621D ✓ ActifPCA9621D Présentation
An I/O expander is an interface IC that adds independently controlled digital outputs to a host processor. The PCA9621D belongs to the broader serial-interface controller hierarchy: it receives register writes over a 2-wire bus and converts those commands into eight configurable output-port states. This architecture reduces the number of GPIO pins required by a host and makes it useful when an embedded controller needs additional discrete output drive.
The primary headline specifications are an 8-bit output port, 65 mA sink capability per device output, and operation from a 2-wire serial interface with support for I2C and SMBus. Its 16-SO package supports compact surface-mount PCB layouts. The output state is held in a programmable 8-bit register that the host can read and write through the serial interface.
Each output can be treated as a general-purpose logic output rather than being limited to a conventional LED-driver function. The NXP product page specifically identifies the 65 mA sink capability as suitable for driving LEDs, while the general-purpose output architecture also supports relay, indicator, or logic-level signaling where the electrical limits are respected. The serial interface allows the host microcontroller to update output patterns without dedicating eight separate GPIO pins.
Typical uses include status and indicator LED banks, alarm and warning lamps, industrial annunciation panels, lighting-control modules, and embedded systems with limited GPIO availability. A microcontroller or other 2-wire-bus controller writes the desired output pattern to the PCA9621D, and the device presents the corresponding states at its eight outputs. A device such as the PCA9621D can therefore consolidate repetitive indicator or lamp control into one serial interface.
The principal design considerations are the absolute output current limit, the voltage levels accepted by the attached loads, and correct I2C or SMBus implementation. Each load path and output driver must remain within the device's stated 65 mA sink capability, while the PCB must provide adequate copper and thermal margin for the selected duty cycle. The manufacturer datasheet should be used for the complete pin description, electrical limits, timing information, and recommended application circuit.
This page organizes the manufacturer specifications, purchasing information, application guidance, and pin-level design considerations for engineers evaluating the PCA9621D. It also provides a comparison framework for evaluating other 8-bit, 2-wire output-port devices against package, interface, output-current, and functional requirements.
Alternatives de remplacement direct pour PCA9621D — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Aucune alternative de remplacement direct disponible pour ce produit.
Demander des alternativesPCA9621D Spécifications
| Product Type | 8-bit 2-wire bus output port |
| Output Port Width | 8 bits |
| Output Sink Capability | 65 mA |
| Serial Interface | 2-wire bus |
| Supported Bus Standards | I2C-bus, SMBus, PMBus and similar systems |
| Maximum Bus Frequency | 1 MHz |
| Output State Register | Programmable and readable 8-bit register |
| Boîtier | 16-pin SOIC, 3.9 mm wide body |
| Type de montage | Surface mount |
Guide de configuration des broches du PCA9621D 16-pin soic, 3.9 mm wide body
Configuration des broches du PCA9621D (boîtier 16-pin soic, 3.9 mm wide body). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour PCA9621D.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
PCA9621D convient pour 6 applications: Status LED Banks, Industrial Alarm Annunciation, Relay Control Interface, Lighting Control Module, Embedded Indicator Interface, Diagnostic Indicator Panel.
Status LED Banks
The PCA9621D fits status-indicator designs because it combines eight programmable outputs with 65 mA sink capability. A host controller can write a complete output pattern through the 2-wire interface rather than driving eight separate GPIO lines. This simplifies firmware and PCB routing when several lamps, status indicators, or diagnostic LEDs share a controlled board. The NXP manufacturer product page identifies LED driving as a suitable use for the output sink capability. Engineering checks should include LED forward current, supply level, duty cycle, and the complete electrical-limit table. The 16-pin SOIC package also supports conventional compact surface-mount assembly.
Recommandé
Industrial Alarm Annunciation
The PCA9621D is suitable for industrial alarm and annunciation panels because a serial-controlled output port can operate multiple visible or audible indicators without consuming eight host GPIO pins. Its programmable 8-bit register allows the controller to set, clear, and read output states over I2C or SMBus. The NXP product description confirms compatibility with these bus concepts and specifies 65 mA sink capability. Designers must still verify each alarm-driver circuit against the device's output limits and add the appropriate protection for inductive or externally powered loads.
Recommandé
Relay Control Interface
The PCA9621D can provide a compact logic interface for relay-control circuits when each relay driver remains within the output and thermal limits of the system. Its eight-bit output register simplifies grouped control of alarm relays, contactors, or reset signals, and the 65 mA sink specification provides the key output-current reference. Because the device is a general-purpose output port rather than an isolated relay driver, flyback diodes, transistor stages, and separate supply-domain design may still be required. Consult the manufacturer datasheet before connecting inductive loads.
Recommandé
Lighting Control Module
The PCA9621D works well in small lighting-control modules that need several binary lamp channels rather than individually regulated LED drive. The host can update all eight output states over the 2-wire bus, reducing connector count and host-controller pin demand. NXP explicitly identifies the 65 mA sink capability as suitable for LEDs. For production designs, verify that the selected lamp arrangement, resistor or transistor network, and ambient operating conditions stay within the complete manufacturer electrical limits. Add local supply decoupling and keep high-current traces compact.
Recommandé
Embedded Indicator Interface
The PCA9621D is useful in embedded systems where a main controller has reserved most of its GPIO for sensors, communications, or safety functions. Eight additional binary outputs can be controlled through the same two-wire interface used for other bus-connected peripherals, and their states remain readable through the device's output register. The 16-pin SOIC package provides a straightforward surface-mount implementation. Firmware should define register-access sequencing and handle bus errors or contention according to the manufacturer's timing and interface requirements.
Recommandé
Diagnostic Indicator Panel
The PCA9621D can drive a bank of diagnostic indicators in test, measurement, or service equipment where the controller needs to report multiple discrete states. Register-based output control makes it practical to map system states to visible lamps through a compact serial connection. The NXP manufacturer product page identifies the device as an 8-bit 2-wire bus output port with 65 mA sink capability. Panel designers should check current per indicator, the maximum duty cycle, and the power-supply arrangement. The final circuit must comply with the manufacturer's recommended operating conditions.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PCA9621D — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit |
|---|---|
| Package | 16-pin SOIC |
| Brand | NXP Semiconductors |
| Product Type | 2-wire bus output port |
| Output Port Width | 8 bits |
| Output Sink Capability | 65 mA |
| Serial Interface | 2-wire bus |
| Bus Compatibility | I2C-bus, SMBus, PMBus and similar systems |
| Maximum Bus Frequency | 1 MHz |
| Output Control | Programmable and readable 8-bit register |
| Mounting Type | Surface mount |
Principaux différenciateurs
- Eight outputs controlled through a two-wire interface (vs Direct host GPIO outputs)
- Substantial output sink capability for indicator applications (vs Standard logic-only GPIO output)
- Readable and writable output-state register (vs Write-only output driver)
Notes de conception
Treat the 65 mA figure as an output sink capability and verify the actual operating condition, duty cycle, and package thermal limit from the manufacturer datasheet. If one output drives several LEDs, calculate the total current through that output rather than treating each LED independently. Keep the load supply capable of the peak current and provide local supply decoupling close to the device.
Route the 2-wire bus as a compact, controlled-impedance communication path where appropriate, and place the device's required bus and supply capacitors close to their associated pins. Keep the clock and data traces away from high-current LED paths, relay traces, and switching-node copper. Confirm all PCB tracks and pads against the official 16-pin SOIC footprint and pin-description table.
Do not assume that a similarly named LED-driver IC is pin-compatible with the PCA9621D. A drop-in substitution must match the package, pin arrangement, address behavior, output logic, timing, and electrical drive. Likewise, do not connect inductive loads directly without suitable protection and verify the supply-voltage requirements against the complete operating and absolute-maximum tables before layout release.
Informations de conformité
Compliance attributes were not stated in the manufacturer product page or distributor listings included for this MPN. Confirm the current declarations and qualification status in the official PCA9621D documentation before production release.