NXP Semiconductors

PCA9621D - 8-Bit 65mA I/O Expander | NXP | LED Drive

MPN: PCA9621D ✓ Aktif
I2C-bus, SMBus, PMBus and similar systems Rds(on) 16-pin SOIC, 3.9 mm wide body Package 1 MHz Speed
MOQ: 1 |

PCA9621D Ringkasan

The NXP Semiconductors PCA9621D is an 8-bit I/O expander with a 65 mA output sink capability, configurable from a 2-wire bus interface in a 16-pin SOIC package. It supports I2C-bus and SMBus control, while the manufacturer also describes compatibility with PMBus and similar serial-bus systems.

An I/O expander is an interface IC that adds independently controlled digital outputs to a host processor. The PCA9621D belongs to the broader serial-interface controller hierarchy: it receives register writes over a 2-wire bus and converts those commands into eight configurable output-port states. This architecture reduces the number of GPIO pins required by a host and makes it useful when an embedded controller needs additional discrete output drive.

The primary headline specifications are an 8-bit output port, 65 mA sink capability per device output, and operation from a 2-wire serial interface with support for I2C and SMBus. Its 16-SO package supports compact surface-mount PCB layouts. The output state is held in a programmable 8-bit register that the host can read and write through the serial interface.

Each output can be treated as a general-purpose logic output rather than being limited to a conventional LED-driver function. The NXP product page specifically identifies the 65 mA sink capability as suitable for driving LEDs, while the general-purpose output architecture also supports relay, indicator, or logic-level signaling where the electrical limits are respected. The serial interface allows the host microcontroller to update output patterns without dedicating eight separate GPIO pins.

Typical uses include status and indicator LED banks, alarm and warning lamps, industrial annunciation panels, lighting-control modules, and embedded systems with limited GPIO availability. A microcontroller or other 2-wire-bus controller writes the desired output pattern to the PCA9621D, and the device presents the corresponding states at its eight outputs. A device such as the PCA9621D can therefore consolidate repetitive indicator or lamp control into one serial interface.

The principal design considerations are the absolute output current limit, the voltage levels accepted by the attached loads, and correct I2C or SMBus implementation. Each load path and output driver must remain within the device's stated 65 mA sink capability, while the PCB must provide adequate copper and thermal margin for the selected duty cycle. The manufacturer datasheet should be used for the complete pin description, electrical limits, timing information, and recommended application circuit.

This page organizes the manufacturer specifications, purchasing information, application guidance, and pin-level design considerations for engineers evaluating the PCA9621D. It also provides a comparison framework for evaluating other 8-bit, 2-wire output-port devices against package, interface, output-current, and functional requirements.

Alternatif penggantian untuk PCA9621D — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Tidak ada alternatif pengganti yang tersedia untuk produk ini.

Permintaan Alternatif

PCA9621D Spesifikasi

Product Type 8-bit 2-wire bus output port
Output Port Width 8 bits
Output Sink Capability 65 mA
Serial Interface 2-wire bus
Supported Bus Standards I2C-bus, SMBus, PMBus and similar systems
Maximum Bus Frequency 1 MHz
Output State Register Programmable and readable 8-bit register
Paket 16-pin SOIC, 3.9 mm wide body
Tipe Mounting Surface mount

PCA9621D 16-pin soic, 3.9 mm wide body Diamant Konfigurasi Panduan

Konfigurasi pin untuk PCA9621D (16-pin soic, 3.9 mm wide body pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.

Diamant diagram pakai pakai 16-pin soic, 3.9 mm wide body untuk PCA9621D

Tidak ada data diatribut pin yang tersedia untuk PCA9621D.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

PCA9621D cocok untuk 6 aplikasis: Status LED Banks, Industrial Alarm Annunciation, Relay Control Interface, Lighting Control Module, Embedded Indicator Interface, Diagnostic Indicator Panel.

💡

Status LED Banks

The PCA9621D fits status-indicator designs because it combines eight programmable outputs with 65 mA sink capability. A host controller can write a complete output pattern through the 2-wire interface rather than driving eight separate GPIO lines. This simplifies firmware and PCB routing when several lamps, status indicators, or diagnostic LEDs share a controlled board. The NXP manufacturer product page identifies LED driving as a suitable use for the output sink capability. Engineering checks should include LED forward current, supply level, duty cycle, and the complete electrical-limit table. The 16-pin SOIC package also supports conventional compact surface-mount assembly.

🏭

Industrial Alarm Annunciation

The PCA9621D is suitable for industrial alarm and annunciation panels because a serial-controlled output port can operate multiple visible or audible indicators without consuming eight host GPIO pins. Its programmable 8-bit register allows the controller to set, clear, and read output states over I2C or SMBus. The NXP product description confirms compatibility with these bus concepts and specifies 65 mA sink capability. Designers must still verify each alarm-driver circuit against the device's output limits and add the appropriate protection for inductive or externally powered loads.

🔧

Relay Control Interface

The PCA9621D can provide a compact logic interface for relay-control circuits when each relay driver remains within the output and thermal limits of the system. Its eight-bit output register simplifies grouped control of alarm relays, contactors, or reset signals, and the 65 mA sink specification provides the key output-current reference. Because the device is a general-purpose output port rather than an isolated relay driver, flyback diodes, transistor stages, and separate supply-domain design may still be required. Consult the manufacturer datasheet before connecting inductive loads.

💡

Lighting Control Module

The PCA9621D works well in small lighting-control modules that need several binary lamp channels rather than individually regulated LED drive. The host can update all eight output states over the 2-wire bus, reducing connector count and host-controller pin demand. NXP explicitly identifies the 65 mA sink capability as suitable for LEDs. For production designs, verify that the selected lamp arrangement, resistor or transistor network, and ambient operating conditions stay within the complete manufacturer electrical limits. Add local supply decoupling and keep high-current traces compact.

🧩

Embedded Indicator Interface

The PCA9621D is useful in embedded systems where a main controller has reserved most of its GPIO for sensors, communications, or safety functions. Eight additional binary outputs can be controlled through the same two-wire interface used for other bus-connected peripherals, and their states remain readable through the device's output register. The 16-pin SOIC package provides a straightforward surface-mount implementation. Firmware should define register-access sequencing and handle bus errors or contention according to the manufacturer's timing and interface requirements.

🖥️

Diagnostic Indicator Panel

The PCA9621D can drive a bank of diagnostic indicators in test, measurement, or service equipment where the controller needs to report multiple discrete states. Register-based output control makes it practical to map system states to visible lamps through a compact serial connection. The NXP manufacturer product page identifies the device as an 8-bit 2-wire bus output port with 65 mA sink capability. Panel designers should check current per indicator, the maximum duty cycle, and the power-supply arrangement. The final circuit must comply with the manufacturer's recommended operating conditions.

What is the PCA9621D?
The PCA9621D is an 8-bit CMOS output-port expander controlled through a 2-wire serial bus. According to the NXP manufacturer product page, it supports I2C-bus, SMBus, PMBus, and similar systems, while its eight outputs can be read and written through a programmable register. The device is packaged in 16-pin SOIC and is intended for general-purpose output drive.
What are the key specifications of PCA9621D that engineers should know?
The PCA9621D provides eight configurable outputs, 65 mA output sink capability, a 2-wire serial interface, and operation up to 1 MHz bus frequency. The NXP manufacturer product page identifies the device as an 8-bit 2-wire bus output port, and the DigiKey listing identifies its 16-SO package. These are the principal parameters to compare when evaluating output-port expanders.
Can PCA9621D drive LEDs?
Yes, the PCA9621D is suitable for driving LEDs because its outputs have a stated 65 mA sink capability. The NXP manufacturer product page specifically identifies this capability as ideal for LED drive. Actual operating current must remain within the limits specified for the particular output configuration, and the complete electrical-limit table in the manufacturer datasheet governs the final design.
Which serial buses does PCA9621D support?
The PCA9621D supports I2C-bus and SMBus and is also described by NXP as compatible with PMBus and other systems based on similar serial-bus principles. Its configuration registers are accessed through the 2-wire interface. The host controller must use addresses and electrical levels consistent with the device configuration and the selected bus implementation.
How many outputs does the PCA9621D provide?
The PCA9621D provides an 8-bit output port. According to the NXP manufacturer product page, the state of the outputs is determined by a programmable 8-bit register that can be read and written through the 2-wire bus. This allows a controller to manage eight output states while using serial-bus communication instead of eight dedicated GPIO lines.
Where can I download the PCA9621D datasheet?
The official PCA9621D product information and datasheet are available through the NXP product page at https://www.nxp.com/products/PCA9621D. Use the manufacturer document for the definitive pin descriptions, recommended operating conditions, timing characteristics, output-current limits, and application diagram. Request current price and availability through the Request a Quote form on this page.
Where can I find the PCA9621D pinout?
The PCA9621D pinout is identified in the manufacturer datasheet, which is linked from the official NXP product page. The distributor listing confirms that the device uses a 16-pin SOIC package. Use the package drawing and pin-description table in the manufacturer datasheet when assigning PCB tracks and connecting address, clock, supply, ground, and output signals.
What is the maximum output sink current of PCA9621D?
The PCA9621D has a stated output sink capability of 65 mA. NXP identifies this value in the manufacturer product description and associates it with LED-drive applications. Because the figure describes sink capability rather than an unrestricted source-current rating, load current, duty cycle, supply voltage, and package thermal conditions must be checked before using the output at its limit.
Is PCA9621D suitable for a microcontroller with too few GPIO pins?
Yes, the PCA9621D is suitable when a host controller lacks enough general-purpose I/O pins. It adds eight independently controlled outputs through a 2-wire bus, allowing a microcontroller to update the output register over I2C or SMBus. STM32G431C8T6TR and STM32G474VET6TR are examples of general-purpose microcontrollers that can serve as serial-bus controllers when their firmware supports the selected peripheral.
When should I choose PCA9621D instead of a dedicated LED-driver IC?
Choose the PCA9621D when the system needs general-purpose, register-controlled outputs and its stated 65 mA sink capability is sufficient. A dedicated LED-driver IC may be preferable when the design requires independent constant-current channels, extensive dimming registers, or automatic LED-current regulation. The PCA9621D is simpler and appropriate for indicator, status, and general output-port functions.
What is the difference between PCA9621D and a PCA9621D,118 distributor ordering code?
PCA9621D identifies the NXP device and its base ordering configuration, while PCA9621D,118 is the distributor-style ordering suffix used for the 16-pin SO package. The comma and 118 denote the supplier ordering code rather than a different functional device. Validate the package suffix, temperature range, and tape-and-reel details against the manufacturer ordering information before releasing a purchase.
What can replace PCA9621D?
A true replacement for PCA9621D must provide eight outputs, a compatible 16-pin SOIC footprint and pin arrangement, suitable 2-wire-bus timing, and output drive that meets the load requirements. The cross-reference search did not identify a verified drop-in substitute with enough pin-level information to approve one safely. Do not treat a similar output-port or LED-driver MPN as drop-in without checking the manufacturer pinout and electrical limits.
Where can I buy PCA9621D online?
Use the Request a Quote form on this page to request PCA9621D pricing, current inventory, lot-size requirements, and estimated lead time from XAIPART. The target is the base MPN PCA9621D; confirm that the quoted package and ordering suffix correspond to the intended 16-SO configuration. Current commercial terms should be confirmed through the quote response.
What is the price of PCA9621D?
The current price of PCA9621D depends on quantity, package ordering code, inventory, and delivery requirements. Use the Request a Quote form on this page for a current quotation and lead-time confirmation. The structured pricing fields are updated separately from the technical description so that displayed commercial information remains consistent with current sourcing status.
What is the lead time and stock status of PCA9621D?
Request the current PCA9621D stock status, minimum order quantity, and production lead time through the Request a Quote form on this page. Lead time can vary with quantity, package suffix, and replenishment conditions, so an old catalog reference should not be treated as a current availability commitment. Quote confirmation should specify the exact MPN and delivery schedule.
Can a PCA9621D be used for relay or alarm outputs?
Yes, the PCA9621D can control relay drivers, alarm indicators, or logic-level signaling when the load and interface circuitry remain within the device's electrical limits. Its 65 mA sink capability is relevant to the output stage, but coil flyback protection, supply compatibility, and off-state leakage still require separate analysis. Use the manufacturer datasheet for the authoritative absolute-maximum and operating limits.
What design checks matter for a PCA9621D LED board?
Check LED forward current, driver topology, supply voltage, output duty cycle, and total thermal loading before assigning a load. According to the NXP manufacturer product page, the outputs provide 65 mA sink capability and are intended for LED drive. Decouple the supply locally, route high-current return paths carefully, and confirm that every connected load remains compliant with the complete datasheet limits.

Data referensi engineering untuk PCA9621D — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the PCA9621D when a system needs eight general-purpose outputs, a compact 2-wire control path, and up to the stated 65 mA output sink capability. It is particularly effective for status lamps, diagnostic indicators, alarm signals, and basic relay-control interfaces where full independent LED-current regulation is unnecessary. Choose a dedicated LED-driver IC when the design requires constant-current channels, extensive dimming, automatic current setting, or a current sink above the PCA9621D's specified capability. A direct GPIO implementation is simpler for very small projects but consumes more host pins. Do not select a replacement solely by output count or SOIC body size: the substitute must match the 16-pin land pattern, pin functions, serial protocol behavior, address scheme, logic levels, timing, and load-current requirements.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini
Package 16-pin SOIC
Brand NXP Semiconductors
Product Type 2-wire bus output port
Output Port Width 8 bits
Output Sink Capability 65 mA
Serial Interface 2-wire bus
Bus Compatibility I2C-bus, SMBus, PMBus and similar systems
Maximum Bus Frequency 1 MHz
Output Control Programmable and readable 8-bit register
Mounting Type Surface mount

Diferensiator Kunci

  • Eight outputs controlled through a two-wire interface (vsDirect host GPIO outputs)
  • Substantial output sink capability for indicator applications (vsStandard logic-only GPIO output)
  • Readable and writable output-state register (vsWrite-only output driver)

Catatan Desain

Treat the 65 mA figure as an output sink capability and verify the actual operating condition, duty cycle, and package thermal limit from the manufacturer datasheet. If one output drives several LEDs, calculate the total current through that output rather than treating each LED independently. Keep the load supply capable of the peak current and provide local supply decoupling close to the device.

Route the 2-wire bus as a compact, controlled-impedance communication path where appropriate, and place the device's required bus and supply capacitors close to their associated pins. Keep the clock and data traces away from high-current LED paths, relay traces, and switching-node copper. Confirm all PCB tracks and pads against the official 16-pin SOIC footprint and pin-description table.

Do not assume that a similarly named LED-driver IC is pin-compatible with the PCA9621D. A drop-in substitution must match the package, pin arrangement, address behavior, output logic, timing, and electrical drive. Likewise, do not connect inductive loads directly without suitable protection and verify the supply-voltage requirements against the complete operating and absolute-maximum tables before layout release.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

Compliance attributes were not stated in the manufacturer product page or distributor listings included for this MPN. Confirm the current declarations and qualification status in the official PCA9621D documentation before production release.

Data disahkan pada: 2026-11-14 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

PCA9621D datasheet PCA9621D pinout PCA9621D datasheet pdf PCA9621D equivalent PCA9621D replacement PCA9621D cross reference PCA9621D SOIC16 pinout PCA9621D 65mA output PCA9621D 1MHz I2C NXP PCA9621D PCA9621D price PCA9621D stock PCA9621D LED driver application PCA9621D GPIO expander

Komponen dan Istilah Terkait

NXP Semiconductors PCA9621D PCA9621D,118 I/O expander output port 2-wire bus I2C-bus SMBus PMBus CMOS integrated circuit 8-bit output register 65 mA sink current LED driver 16-pin SOIC SOIC package family surface-mount package digital bus interface status indicator industrial alarm relay control interface GPIO expansion programmable output STM32G431C8T6TR STM32G474VET6TR
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ