PCA9674N - 8-Bit 1MHz I2C I/O Expander | NXP
Référence : PCA9674N ✓ ActifPCA9674N Présentation
An I/O expander is an interface IC that extends the number of digital input or output pins available to a microcontroller or other bus controller. The PCA9674 belongs to the broader hierarchy of I2C interface ICs, parallel-port expanders, GPIO controllers, and power-management system semiconductors. It is useful when the host device has insufficient direct GPIO pins or when remote peripherals need to share a two-wire control bus.
Three address-select inputs allow the PCA9674 to be assigned among 64 addresses, supporting up to 126 PCA9674 and PCA9674A devices on one I2C-bus without bus buffers and as many as 1,008 controlled I/Os. Its 1 MHz bus speed exceeds the 100 kHz Standard-mode rate, while the 2.3 V to 5.5 V supply range supports both 3.3 V and 5 V systems. The interrupt output enables a host to respond to port events without continuously polling all eight outputs.
The device separates serial bus control from parallel output handling. The host writes to the PCA9674 registers over I2C and receives an interrupt when a configured output state changes. Its 8-bit organization and hardware-selectable address pins make multiple expanders practical in LED panels, control boards, and distributed peripheral interfaces. The through-hole 16-DIP format is also convenient for prototyping and through-hole industrial assemblies.
Typical uses include LED status indicators, relay or contactor control, display and keypad interfaces, industrial control modules, and general-purpose board I/O expansion. The PCA9674 is particularly suitable when a microcontroller must monitor remote logic states while preserving limited pins for communications, timing, or analog functions.
For reliable implementation, connect pull-up resistors to the SDA and SCL lines, route the bus away from noisy switching nodes, and treat the address pins as board-level configuration. Verify the 2.3 V to 5.5 V operating range against the voltage applied to VDD and the logic levels used by the connected host.
This page consolidates the NXP device specifications, address architecture, package information, selection guidance, and practical integration notes. It also identifies the closest same-footprint alternatives while clearly distinguishing confirmed orderable variants from functionally similar devices that require additional design review.
Alternatives de remplacement direct pour PCA9674N — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
PCA9674N,112
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PCA9674
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PCA9674A
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
PCA9674A,112
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
PCA9674N Spécifications
| Product Type | 8-bit remote I/O expander |
| Interface | I2C-bus |
| I2C Bus Speed | 1 MHz |
| Number of I/O | 8 outputs |
| Supply Voltage Range | 2.3 V to 5.5 V |
| Maximum Supply Voltage | 5.5 V |
| Address Select Inputs | 3 hardware address pins |
| PCA9674 Decoded Addresses | 64 addresses |
| Combined PCA9674 and PCA9674A Bus Capacity | Up to 126 expanders |
| Combined I/O Capacity | Up to 1,008 I/Os |
| Interrupt Output | Yes |
| Boîtier | 16-DIP, 0.300 inch, 7.62 mm pitch |
| Nombre de broches | 16 pins |
| Type de montage | Through-hole |
| Temperature Grade | Industrial |
| Pull-Up Configuration | Software-configurable pull-ups |
Configuration des broches de PCA9674N
| Broche 1 | A0 — Hardware-selectable address input 0 |
| Broche 2 | A1 — Hardware-selectable address input 1 |
| Broche 3 | A2 — Hardware-selectable address input 2 |
| Broche 4 | SCL — I2C serial clock input |
| Broche 5 | SDA — I2C serial data input and output |
| Broche 6 | INT — Interrupt output for port events |
| Broche 7 | P0 — I/O port bit 0 |
| Broche 8 | P1 — I/O port bit 1 |
| Broche 9 | P2 — I/O port bit 2 |
| Broche 10 | P3 — I/O port bit 3 |
| Broche 11 | GND — Ground |
| Broche 12 | VDD — Positive supply voltage |
| Broche 13 | P4 — I/O port bit 4 |
| Broche 14 | P5 — I/O port bit 5 |
| Broche 15 | P6 — I/O port bit 6 |
| Broche 16 | P7 — I/O port bit 7 |
Applications typiques
PCA9674N convient pour 6 applications: Industrial Control and Automation, LED Status and Signage Panels, Relay and Discrete Actuator Control, Remote Sensor and Peripheral Interface, Instrumentation and Test Equipment, Human-Machine Interface Control.
Industrial Control and Automation
The PCA9674N fits industrial controller boards that need additional relay, alarm, valve, or status outputs without expanding the host footprint. Its 8-bit parallel output structure connects to external logic drivers while the 1 MHz I2C-bus communicates efficiently with a host microcontroller. Three hardware address inputs allow several expanders to share one bus, and the interrupt output lets the controller react to output-state changes rather than polling continuously. Its 2.3 V to 5.5 V operating range supports common industrial logic levels, while the 16-DIP package simplifies through-hole assembly and prototype rework.
Recommandé
LED Status and Signage Panels
The PCA9674N is useful for LED status panels because one expander controls eight outputs while the host manages patterns over I2C. The 1 MHz bus rate allows the controller to update several boards efficiently, and the three address-select pins can identify different panel sections. The interrupt output can notify the host when an output condition changes, reducing unnecessary register reads. Operating from 2.3 V to 5.5 V accommodates both 3.3 V and 5 V control systems, while the DIP package provides a straightforward through-hole implementation for prototype and industrial boards.
Recommandé
Relay and Discrete Actuator Control
The PCA9674N can provide the logic-side interface for relays, contactors, solenoids, and discrete driver stages while the host retains control over timing and interlocks. Its eight outputs reduce the number of host GPIO pins required for actuator addressing, and the 1 MHz I2C-bus supports rapid command traffic across a controller board. Because the device operates up to 5.5 V, its logic system must remain compatible with the chosen relay drivers. Use appropriate flyback protection and driver transistors for inductive loads, and route high-current switching paths separately from sensitive bus traces.
Recommandé
Remote Sensor and Peripheral Interface
The PCA9674N extends a microcontroller-based peripheral board with eight digital outputs that can represent sensor-enable lines, device resets, mode controls, or logic-level triggers. The host communicates over the 2-wire I2C interface and can use the interrupt output to react to relevant events. The 1 MHz bus capability is useful in compact control systems where several peripheral functions must share limited wiring. Its three address inputs permit parallel expansion, and the 16-DIP footprint provides through-hole accessibility for industrial or educational control assemblies.
Recommandé
Instrumentation and Test Equipment
The PCA9674N can organize front-panel and back-panel control lines in instrumentation by giving the host an interrupt-capable interface to multiple digital output channels. It is suitable for controlling relay matrices, programmable indicators, test enables, and equipment modes through a common I2C bus. The 1 MHz interface reduces command latency, while the 2.3 V minimum supply supports low-voltage control sections. The 16-DIP package is particularly convenient in through-hole laboratory designs and legacy measurement platforms that require an easy-to-replace expansion component.
Recommandé
Human-Machine Interface Control
The PCA9674N can manage LEDs, buzzers, display enables, and panel control lines while a host microcontroller handles user input and application logic. Eight outputs provide a convenient parallel interface, and the I2C-bus keeps the PCB routing practical when multiple HMI sections share one controller. The interrupt line supports event-driven host operation, while three address pins allow additional expanders for larger panels. Its 1 MHz interface and broad 2.3 V to 5.5 V supply range fit both 3.3 V and 5 V embedded systems, and the through-hole DIP package simplifies rework.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PCA9674N — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PCA9674N,112 | PCA9674 | PCA9674A | PCA9674A,112 |
|---|---|---|---|---|---|
| Package | 16-DIP, 0.300 inch, 7.62 mm pitch | 16-DIP, 0.300 inch, 7.62 mm pitch | 16-DIP | 16-DIP | 16-DIP |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Number of I/O | 8 outputs | 8 outputs | 8 outputs | 8 outputs | 8 outputs |
| I2C Interface | Fast-mode Plus I2C-bus | Fast-mode Plus I2C-bus | Fast-mode Plus I2C-bus | Fast-mode Plus I2C-bus | Fast-mode Plus I2C-bus |
| Decoded Addresses | 64 addresses | 64 addresses | 64 addresses | 62 addresses | 62 addresses |
| Interrupt Output | Yes | Yes | Yes | Yes; polarity requires verification | Yes; polarity requires verification |
| Address Configuration | Three hardware-selectable address pins | Three hardware-selectable address pins | Three hardware-selectable address pins | Three hardware-selectable address pins | Three hardware-selectable address pins |
Principaux différenciateurs
- Full 64-address decoding within the original PCA9674 family (vs PCA9674A)
- Established 1 MHz Fast-mode Plus I2C interface (vs PCA9674A)
- Direct through-hole replacement ordering support (vs PCA9674A,112)
Notes de conception
Place SDA and SCL pull-up resistors close to the bus master or the point where the bus branches from its main segment. Calculate the effective resistance against the total bus capacitance and the maximum clock rate of 1 MHz. Do not duplicate strong pull-ups unnecessarily on every expander, since parallel resistance can make the effective value too low and increase the low-level discharge requirement.
Keep the PCA9674N away from relay drivers, switching power stages, high-current edge outputs, and long antenna-like traces. Route SDA and SCL together where practical to reduce differential pickup, provide a continuous ground reference, and avoid sharing a narrow ground path with return currents from inductive or capacitive loads. The interrupt trace should also remain away from switching nodes.
Do not assume the PCA9674A is an unconditional substitute for the PCA9674N. The PCA9674A provides 62 decoded addresses rather than 64, and its interrupt behavior differs. Before using either A variant, verify the package orderable suffix, compare the NXP datasheets pin by pin, and confirm that existing firmware initializes the configuration, polarity, and interrupt registers correctly.
Informations de conformité
The PCA9674N is listed as an industrial-grade device, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was identified. Confirm the current declarations and material documentation with NXP before qualification.