NXP Semiconductors

PCA9674N - 8-Bit 1MHz I2C I/O Expander | NXP

Артикул: PCA9674N ✓ Активен
2.3 V to 5.5 V Vdss 16-DIP, 0.300 inch, 7.62 mm pitch Package 1 MHz Speed
MOQ: 1 |

PCA9674N Обзор

The NXP Semiconductors PCA9674N is an 8-bit remote I/O expander with a 1 MHz Fast-mode Plus I2C-bus interface, operating from 2.3 V to 5.5 V and housed in a 16-pin DIP package. It adds eight independently controlled GPIO outputs to a host microcontroller while providing an interrupt output for change notification.

An I/O expander is an interface IC that extends the number of digital input or output pins available to a microcontroller or other bus controller. The PCA9674 belongs to the broader hierarchy of I2C interface ICs, parallel-port expanders, GPIO controllers, and power-management system semiconductors. It is useful when the host device has insufficient direct GPIO pins or when remote peripherals need to share a two-wire control bus.

Three address-select inputs allow the PCA9674 to be assigned among 64 addresses, supporting up to 126 PCA9674 and PCA9674A devices on one I2C-bus without bus buffers and as many as 1,008 controlled I/Os. Its 1 MHz bus speed exceeds the 100 kHz Standard-mode rate, while the 2.3 V to 5.5 V supply range supports both 3.3 V and 5 V systems. The interrupt output enables a host to respond to port events without continuously polling all eight outputs.

The device separates serial bus control from parallel output handling. The host writes to the PCA9674 registers over I2C and receives an interrupt when a configured output state changes. Its 8-bit organization and hardware-selectable address pins make multiple expanders practical in LED panels, control boards, and distributed peripheral interfaces. The through-hole 16-DIP format is also convenient for prototyping and through-hole industrial assemblies.

Typical uses include LED status indicators, relay or contactor control, display and keypad interfaces, industrial control modules, and general-purpose board I/O expansion. The PCA9674 is particularly suitable when a microcontroller must monitor remote logic states while preserving limited pins for communications, timing, or analog functions.

For reliable implementation, connect pull-up resistors to the SDA and SCL lines, route the bus away from noisy switching nodes, and treat the address pins as board-level configuration. Verify the 2.3 V to 5.5 V operating range against the voltage applied to VDD and the logic levels used by the connected host.

This page consolidates the NXP device specifications, address architecture, package information, selection guidance, and practical integration notes. It also identifies the closest same-footprint alternatives while clearly distinguishing confirmed orderable variants from functionally similar devices that require additional design review.

Аналоги без доработки для PCA9674N — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

PCA9674N,112

✅ Прямая замена
📦 16-DIP (0.300 inch, 7.62 mm pitch)
Identical 8-bit, 1 MHz, 2.3 V to 5.5 V device; 112 is the orderable suffix for the same 16-DIP function

📋 Справочный аналог (нет в каталоге)

PCA9674

✅ Прямая замена
📦 16-DIP (0.300 inch, 7.62 mm pitch)
Same PCA9674 function and 64-address architecture; package suffix and ordering-code presentation differ

📋 Справочный аналог (нет в каталоге)

PCA9674A

✅ Прямая замена ⚠️ Характеристики не проверены
📦 16-DIP (0.300 inch, 7.62 mm pitch)
Same 8-bit Fast-mode Plus architecture, but decoded addresses decrease from 64 to 62 and interrupt behavior requires verification

📋 Справочный аналог (нет в каталоге)

PCA9674A,112

✅ Прямая замена ⚠️ Характеристики не проверены
📦 16-DIP (0.300 inch, 7.62 mm pitch)
Same 8-bit Fast-mode Plus architecture; 62 decoded addresses versus 64 and revised interrupt behavior versus PCA9674N

📋 Справочный аналог (нет в каталоге)

PCA9674N Характеристики

Product Type 8-bit remote I/O expander
Интерфейс I2C-bus
I2C Bus Speed 1 MHz
Number of I/O 8 outputs
Supply Voltage Range 2.3 V to 5.5 V
Maximum Supply Voltage 5.5 V
Address Select Inputs 3 hardware address pins
PCA9674 Decoded Addresses 64 addresses
Combined PCA9674 and PCA9674A Bus Capacity Up to 126 expanders
Combined I/O Capacity Up to 1,008 I/Os
Interrupt Output Yes
Корпус 16-DIP, 0.300 inch, 7.62 mm pitch
Число выводов 16 pins
Тип монтажа Through-hole
Temperature Grade Industrial
Pull-Up Configuration Software-configurable pull-ups

Конфигурация выводов PCA9674N

DIP-16 Package Pinout Diagram DIP-16 16-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 DIP-16
Контакт 1 A0 — Hardware-selectable address input 0
Контакт 2 A1 — Hardware-selectable address input 1
Контакт 3 A2 — Hardware-selectable address input 2
Контакт 4 SCL — I2C serial clock input
Контакт 5 SDA — I2C serial data input and output
Контакт 6 INT — Interrupt output for port events
Контакт 7 P0 — I/O port bit 0
Контакт 8 P1 — I/O port bit 1
Контакт 9 P2 — I/O port bit 2
Контакт 10 P3 — I/O port bit 3
Контакт 11 GND — Ground
Контакт 12 VDD — Positive supply voltage
Контакт 13 P4 — I/O port bit 4
Контакт 14 P5 — I/O port bit 5
Контакт 15 P6 — I/O port bit 6
Контакт 16 P7 — I/O port bit 7

Типичное применение

PCA9674N подходит для 6 применениеs: Industrial Control and Automation, LED Status and Signage Panels, Relay and Discrete Actuator Control, Remote Sensor and Peripheral Interface, Instrumentation and Test Equipment, Human-Machine Interface Control.

🏭

Industrial Control and Automation

The PCA9674N fits industrial controller boards that need additional relay, alarm, valve, or status outputs without expanding the host footprint. Its 8-bit parallel output structure connects to external logic drivers while the 1 MHz I2C-bus communicates efficiently with a host microcontroller. Three hardware address inputs allow several expanders to share one bus, and the interrupt output lets the controller react to output-state changes rather than polling continuously. Its 2.3 V to 5.5 V operating range supports common industrial logic levels, while the 16-DIP package simplifies through-hole assembly and prototype rework.

💡

LED Status and Signage Panels

The PCA9674N is useful for LED status panels because one expander controls eight outputs while the host manages patterns over I2C. The 1 MHz bus rate allows the controller to update several boards efficiently, and the three address-select pins can identify different panel sections. The interrupt output can notify the host when an output condition changes, reducing unnecessary register reads. Operating from 2.3 V to 5.5 V accommodates both 3.3 V and 5 V control systems, while the DIP package provides a straightforward through-hole implementation for prototype and industrial boards.

⚡

Relay and Discrete Actuator Control

The PCA9674N can provide the logic-side interface for relays, contactors, solenoids, and discrete driver stages while the host retains control over timing and interlocks. Its eight outputs reduce the number of host GPIO pins required for actuator addressing, and the 1 MHz I2C-bus supports rapid command traffic across a controller board. Because the device operates up to 5.5 V, its logic system must remain compatible with the chosen relay drivers. Use appropriate flyback protection and driver transistors for inductive loads, and route high-current switching paths separately from sensitive bus traces.

🧩

Remote Sensor and Peripheral Interface

The PCA9674N extends a microcontroller-based peripheral board with eight digital outputs that can represent sensor-enable lines, device resets, mode controls, or logic-level triggers. The host communicates over the 2-wire I2C interface and can use the interrupt output to react to relevant events. The 1 MHz bus capability is useful in compact control systems where several peripheral functions must share limited wiring. Its three address inputs permit parallel expansion, and the 16-DIP footprint provides through-hole accessibility for industrial or educational control assemblies.

🔧

Instrumentation and Test Equipment

The PCA9674N can organize front-panel and back-panel control lines in instrumentation by giving the host an interrupt-capable interface to multiple digital output channels. It is suitable for controlling relay matrices, programmable indicators, test enables, and equipment modes through a common I2C bus. The 1 MHz interface reduces command latency, while the 2.3 V minimum supply supports low-voltage control sections. The 16-DIP package is particularly convenient in through-hole laboratory designs and legacy measurement platforms that require an easy-to-replace expansion component.

📺

Human-Machine Interface Control

The PCA9674N can manage LEDs, buzzers, display enables, and panel control lines while a host microcontroller handles user input and application logic. Eight outputs provide a convenient parallel interface, and the I2C-bus keeps the PCB routing practical when multiple HMI sections share one controller. The interrupt line supports event-driven host operation, while three address pins allow additional expanders for larger panels. Its 1 MHz interface and broad 2.3 V to 5.5 V supply range fit both 3.3 V and 5 V embedded systems, and the through-hole DIP package simplifies rework.

What is the PCA9674N and what does it do?
The PCA9674N is an 8-bit remote I/O expander that adds eight parallel output lines to a host through an I2C-bus. According to the NXP manufacturer datasheet, it supports a 1 MHz Fast-mode Plus interface, a 2.3 V to 5.5 V supply range, and an interrupt output for notifying the host of output-state changes.
What is the operating voltage of the PCA9674N?
The PCA9674N operates from 2.3 V to 5.5 V. This range supports 3.3 V and 5 V systems, although the connected I2C host, pull-up network, and external peripherals must use compatible logic levels. The NXP manufacturer datasheet identifies 5.5 V as the maximum device supply voltage.
How many I/O ports does the PCA9674N provide?
The PCA9674N provides eight parallel I/O lines, configured as outputs for controlling LEDs, relays, or other digital loads. The NXP manufacturer datasheet identifies the PCA9674 as an 8-bit remote I/O expander with a 1 MHz I2C interface and an interrupt output.
What is the I2C bus speed of the PCA9674N?
The PCA9674N supports an I2C-bus frequency of 1 MHz, placing it in the Fast-mode Plus performance class. The NXP manufacturer datasheet describes the PCA9674 as a remote 8-bit I/O expander for the Fast-mode Plus I2C-bus, while the published distributor specifications also identify the clock speed as 1 MHz.
How many PCA9674 devices can share one I2C bus?
The PCA9674 can decode 64 bus addresses through three hardware-selectable address pins. The NXP product information states that PCA9674 and PCA9674A devices can share the same I2C-bus without bus buffers, supporting up to 126 expanders and as many as 1,008 I/Os.
What package and pinout does the PCA9674N use?
The PCA9674N uses a through-hole 16-DIP package with a 0.300 inch body and 7.62 mm lead pitch. Its pin arrangement includes three address inputs, SCL and SDA, an interrupt output, eight I/O lines, ground, and supply. Use the NXP manufacturer pin-description table when assigning PCB tracks.
Where can I download the PCA9674N datasheet PDF?
The PCA9674N datasheet PDF is linked from the official NXP product page at https://www.nxp.com/part/PCA9674N. That page provides the manufacturer datasheet and identifies the device as a remote 8-bit I/O expander for a Fast-mode Plus I2C-bus with an interrupt output.
Does the PCA9674N need pull-up resistors on SDA and SCL?
Yes, the I2C-bus requires pull-up resistors on SDA and SCL to support its open-drain signaling. The PCA9674N includes pull-up capability that can be enabled or disabled in its configuration register, but the final bus design must account for resistor value, bus capacitance, speed, and the pull-ups already present elsewhere on the board.
What is the difference between PCA9674N and PCA9674N,112?
PCA9674N and PCA9674N,112 identify the same NXP 16-DIP device, but PCA9674N,112 is the distributor ordering designation. Published listings describe both as an 8-bit 1 MHz I2C I/O expander in a 16-DIP package. The suffix should be checked against the manufacturer's ordering information before treating it as a separate functional alternative.
What is the best drop-in replacement for PCA9674N?
The closest documented same-footprint option is PCA9674N,112, which uses the same NXP 16-DIP device and electrical function. PCA9674A variants may also fit the 16-DIP outline, but their interrupt behavior and address count differ, so firmware and board compatibility must be checked before substitution.
Can a PCA9674A replace a PCA9674N?
A PCA9674A can be considered when the 16-DIP footprint and primary I2C interface match the PCA9674N, but it is not functionally identical. The NXP product information states that the PCA9674A decodes 62 addresses instead of the PCA9674's 64, and its interrupt polarity should also be verified before replacing the original part.
When should I choose PCA9674N over a PCA9674A?
Choose the PCA9674N when the design needs the full 64-address capability of the original PCA9674 family and its established interrupt behavior. Choose a compatible PCA9674A variant when the application can accept 62 decoded addresses and the revised interrupt configuration. Both must be checked against the exact package and host firmware.
PCA9674N vs PCA9674A: which is better for address-heavy designs?
The PCA9674N is the better choice when maximum decoded address availability is important because it provides 64 addresses, while the PCA9674A provides 62 according to NXP product information. The PCA9674N remains the closer functional match to the original design and avoids interrupt-polarity revisions associated with selecting the PCA9674A family.
Is PCA9674N suitable for industrial control and automation systems?
The PCA9674N is suitable for industrial control modules that operate on a 2.3 V to 5.5 V rail and need eight remotely controlled digital outputs. Its industrial temperature grade, 1 MHz I2C interface, hardware address selection, and interrupt output support deterministic bus communication and event-driven host control.
Where can I buy PCA9674N and what is its lead time?
Use the Request a Quote form on this page to ask for PCA9674N availability, current lead time, minimum order quantity, and tube packaging. Current commercial terms are confirmed through the quote process rather than represented by a static price or inventory claim.
What is the price of PCA9674N?
Use the Request a Quote form on this page for the current PCA9674N price, quantity breaks, stock status, and lead time. The structured pricing area updates commercial terms as sourcing data changes, so a static price should not be used for budgeting or procurement.
Is PCA9674N currently in stock?
Current PCA9674N stock and available quantity should be confirmed through the Request a Quote form on this page. Because inventory can change by package and order quantity, avoid assuming availability from a generic product listing or from historical sourcing information.

Справочные инженерные данные для PCA9674N — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose PCA9674N when the design requires the established 8-bit PCA9674 behavior, full 64-address decoding, and a specified 1 MHz Fast-mode Plus I2C interface in a 16-DIP package. PCA9674N,112 is appropriate when it is the required manufacturer ordering code for that same device function. Consider PCA9674A or PCA9674A,112 only after checking the package suffix, revised interrupt behavior, and the reduction from 64 to 62 decoded addresses. These A-family devices may suit new designs that do not depend on the original address map, but existing firmware should not be transferred without review. For designs where the exact PCA9674N function is not mandatory, evaluate broader GPIO expanders only after a separate footprint, electrical, and firmware qualification; parts with a different package are not drop-in replacements.

Сравнение с аналогами

Параметр Этот товар PCA9674N,112 PCA9674 PCA9674A PCA9674A,112
Package 16-DIP, 0.300 inch, 7.62 mm pitch 16-DIP, 0.300 inch, 7.62 mm pitch 16-DIP 16-DIP 16-DIP
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Number of I/O 8 outputs 8 outputs 8 outputs 8 outputs 8 outputs
I2C Interface Fast-mode Plus I2C-bus Fast-mode Plus I2C-bus Fast-mode Plus I2C-bus Fast-mode Plus I2C-bus Fast-mode Plus I2C-bus
Decoded Addresses 64 addresses 64 addresses 64 addresses 62 addresses 62 addresses
Interrupt Output Yes Yes Yes Yes; polarity requires verification Yes; polarity requires verification
Address Configuration Three hardware-selectable address pins Three hardware-selectable address pins Three hardware-selectable address pins Three hardware-selectable address pins Three hardware-selectable address pins

Ключевые отличия

  • Full 64-address decoding within the original PCA9674 family (против PCA9674A)
  • Established 1 MHz Fast-mode Plus I2C interface (против PCA9674A)
  • Direct through-hole replacement ordering support (против PCA9674A,112)

Заметки по проектированию

Place SDA and SCL pull-up resistors close to the bus master or the point where the bus branches from its main segment. Calculate the effective resistance against the total bus capacitance and the maximum clock rate of 1 MHz. Do not duplicate strong pull-ups unnecessarily on every expander, since parallel resistance can make the effective value too low and increase the low-level discharge requirement.

Keep the PCA9674N away from relay drivers, switching power stages, high-current edge outputs, and long antenna-like traces. Route SDA and SCL together where practical to reduce differential pickup, provide a continuous ground reference, and avoid sharing a narrow ground path with return currents from inductive or capacitive loads. The interrupt trace should also remain away from switching nodes.

Do not assume the PCA9674A is an unconditional substitute for the PCA9674N. The PCA9674A provides 62 decoded addresses rather than 64, and its interrupt behavior differs. Before using either A variant, verify the package orderable suffix, compare the NXP datasheets pin by pin, and confirm that existing firmware initializes the configuration, polarity, and interrupt registers correctly.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The PCA9674N is listed as an industrial-grade device, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was identified. Confirm the current declarations and material documentation with NXP before qualification.

Данные проверены: 2026-11-14 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

PCA9674N datasheet PCA9674N pinout PCA9674N datasheet pdf PCA9674N 16-DIP pinout PCA9674N application circuit PCA9674N I2C interface PCA9674N 1MHz I2C expander PCA9674N equivalent PCA9674N replacement PCA9674N vs PCA9674A PCA9674N price PCA9674N stock NXP PCA9674N

Связанные компоненты & термины

NXP Semiconductors PCA9674N PCA9674N,112 PCA9674 PCA9674A PCA9674A,112 I/O expander GPIO controller parallel-port expander I2C Fast-mode Plus remote 8-bit I/O expansion interrupt output hardware-selectable address pins 2.3 V to 5.5 V supply 1 MHz bus clock 16-DIP package through-hole package LED panel control industrial automation relay control human-machine interface STM32G474VET6TR STM32G431C8T6TR
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ