PIC16C77-04I/P - 8-Bit OTP MCU 14KB 4MHz 40-PDIP | Microchip
Référence : PIC16C77-04I/P ✗ Fin de vie| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $11.2 | $11,20 |
| 10 | $9.95 | $99,50 |
| 100 | $8.4 | $840,00 |
| 500 | $7.1 | $3 550,00 |
| 1 000 | $6.05 | $6 050,00 |
PIC16C77-04I/P Présentation
A PIC16C microcontroller is a member of Microchip's PIC (Peripheral Interface Controller) family of RISC-based 8-bit microcontrollers, sitting within the mid-range PIC16 hierarchy. It belongs to the broader category of microcontrollers -> embedded processors -> semiconductor ICs. The '16C' suffix indicates CMOS One-Time Programmable (OTP) EPROM program memory, distinguishing it from the flash-based PIC16F family and the ROM-based PIC16CR family. PIC16C7x parts were among the first mid-range PICs to integrate on-chip ADC, freeing designs from external analog conversion.
Key features include 35 single-word instructions (single-cycle except program branches which take two cycles), 8-level deep hardware stack, 14-bit instruction word, an operating voltage range of 4.0V to 5.5V, and an industrial temperature range of -40C to +85C (denoted by the 'I' suffix). The 40-pin PDIP package is a through-hole form factor suitable for development, prototyping, educational kits, and legacy production systems that require socketed devices for field replacement.
Technical depth: the part uses a Harvard architecture with separate program and data buses, allowing instruction fetch to overlap with data access. The RISC-style instruction set keeps most operations single-cycle, so throughput at 4MHz is approximately 4 MIPS. On-chip peripherals include a USART for serial communication, MSSP (Master Synchronous Serial Port) for SPI/I2C, and 8 channels of 8-bit ADC for sensor interfacing. The industrial-grade temperature range and OTP memory make this part well-suited to medium-volume production where Flash reprogrammability is not required.
Typical applications include industrial control systems, HVAC controllers, motor control front-ends, sensor signal conditioning, embedded instrumentation, and educational/hobbyist microcontroller boards. The on-chip ADC and PWM peripherals suit closed-loop feedback designs such as temperature controllers and small DC motor drivers.
When designing with this part, note that OTP memory cannot be erased or reprogrammed - firmware must be 100% verified before programming. Engineers should consider the newer PIC16F77 (Flash-based) for new designs, or PIC16C77-04/PQ / 04/L variants if a different package is needed while preserving pinout compatibility within the family.
This page synthesizes distributor pricing, same-family drop-in alternatives, and design considerations not found on the manufacturer datasheet front page.
Alternatives de remplacement direct pour PIC16C77-04I/P — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC16C77-04I/P (même facteur de forme et même empreinte) — différant par Core Architecture, Timers, Package, Operating Temperature, Mounting Type.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC16F77-I/P
✅ Remplacement direct✓ En stock
$8.4 / unité
Voir la fiche technique →PIC16C77-04/PT
✅ Remplacement direct✓ En stock
$6.08 / unité
Voir la fiche technique →PIC16C765-I/P
✅ Remplacement direct✓ En stock
$5.1 / unité
Voir la fiche technique →PIC16C74B-04I/P
✅ Remplacement direct✓ En stock
$5.55 / unité
Voir la fiche technique →PIC16C77-04I/P Valeurs maximales et caractéristiques électriques
| Core Architecture | PIC (8-bit RISC, Harvard) |
| Family | PIC16C7x (mid-range) |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 14 KB (8K x 14 words) |
| RAM | 368 bytes |
| Fréquence d'horloge maximale | 4 MHz |
| Instruction Cycle Time | 200 ns |
| Tension d'alimentation | 4.0 V to 5.5 V |
| Number of I/O Pins | 33 |
| ADC | 8 channels, 8-bit |
| Timers | 1 x 8-bit, 1 x 16-bit (via CCP) |
| CCP Modules | 2 |
| Serial Interfaces | USART, MSSP (SPI/I2C) |
| Température de fonctionnement | -40 C to +85 C (Industrial, 'I' suffix) |
| Boîtier | 40-pin PDIP (Plastic DIP, 0.600 in / 15.24 mm) |
| Nombre de broches | 40 |
| Type de montage | Through-Hole (THT) |
| Lead-Free / RoHS | Lead-free per Microchip product page; RoHS compliance varies by date code |
Configuration des broches de PIC16C77-04I/P
| Broche 1 | MCLR/VPP — Master Clear (reset) input / programming voltage |
| Broche 2 | RA0/AN0 — Port A bit 0 / Analog input channel 0 |
| Broche 3 | RA1/AN1 — Port A bit 1 / Analog input channel 1 |
| Broche 4 | RA2/AN2 — Port A bit 2 / Analog input channel 2 |
| Broche 5 | RA3/AN3/VREF — Port A bit 3 / Analog input channel 3 / VREF+ |
| Broche 6 | RA4/T0CKI — Port A bit 4 / Timer0 clock input |
| Broche 7 | RA5/AN4/SS — Port A bit 5 / Analog input channel 4 / SPI slave select |
| Broche 8 | RE0/RD/AN5 — Port E bit 0 / Parallel port read / Analog input channel 5 |
| Broche 9 | RE1/WR/AN6 — Port E bit 1 / Parallel port write / Analog input channel 6 |
| Broche 10 | RE2/CS/AN7 — Port E bit 2 / Parallel port chip select / Analog input channel 7 |
| Broche 11 | VDD — Positive supply voltage (5V) |
| Broche 12 | VSS — Ground reference |
| Broche 13 | OSC1/CLKIN — Crystal oscillator input / external clock input |
| Broche 14 | OSC2/CLKOUT — Crystal oscillator output / clock output (Fosc/4) |
| Broche 15 | RC0/T1OSO/T1CKI — Port C bit 0 / Timer1 oscillator output / Timer1 clock input |
| Broche 16 | RC1/T1OSI/CCP2 — Port C bit 1 / Timer1 oscillator input / CCP2 module |
| Broche 17 | RC2/CCP1 — Port C bit 2 / CCP1 module (PWM/Capture/Compare) |
| Broche 18 | RC3/SCK/SCL — Port C bit 3 / SPI clock / I2C clock |
| Broche 19 | RD0/PSP0 — Port D bit 0 / Parallel Slave Port bit 0 |
| Broche 20 | RD1/PSP1 — Port D bit 1 / Parallel Slave Port bit 1 |
| Broche 21 | RD2/PSP2 — Port D bit 2 / Parallel Slave Port bit 2 |
| Broche 22 | RD3/PSP3 — Port D bit 3 / Parallel Slave Port bit 3 |
| Broche 23 | RC4/SDI/SDA — Port C bit 4 / SPI data in / I2C data |
| Broche 24 | RC5/SDO — Port C bit 5 / SPI data out |
| Broche 25 | RC6/TX/CK — Port C bit 6 / USART TX / USART clock |
| Broche 26 | RC7/RX/DT — Port C bit 7 / USART RX / USART data |
| Broche 27 | RD4/PSP4 — Port D bit 4 / Parallel Slave Port bit 4 |
| Broche 28 | RD5/PSP5 — Port D bit 5 / Parallel Slave Port bit 5 |
| Broche 29 | RD6/PSP6 — Port D bit 6 / Parallel Slave Port bit 6 |
| Broche 30 | RD7/PSP7 — Port D bit 7 / Parallel Slave Port bit 7 |
| Broche 31 | VSS — Ground reference |
| Broche 32 | VDD — Positive supply voltage (5V) |
| Broche 33 | RB0/INT — Port B bit 0 / External interrupt |
| Broche 34 | RB1 — Port B bit 1 |
| Broche 35 | RB2 — Port B bit 2 |
| Broche 36 | RB3/PGM — Port B bit 3 / Low-voltage programming |
| Broche 37 | RB4 — Port B bit 4 |
| Broche 38 | RB5 — Port B bit 5 |
| Broche 39 | RB6/PGC — Port B bit 6 / ICSP clock |
| Broche 40 | RB7/PGD — Port B bit 7 / ICSP data |
Applications typiques
PIC16C77-04I/P convient pour 6 applications: Industrial Process Control, HVAC Climate Controllers, Small DC Motor and Stepper Control, Educational and Hobbyist Microcontroller Boards, Sensor Signal Conditioning Front-Ends, Legacy Embedded Instrumentation.
Industrial Process Control
The PIC16C77-04I/P fits industrial process control applications because of its 8-channel 8-bit ADC for sensor interfacing (thermistors, pressure transducers, flow meters), 33 digital I/O pins for actuator and relay driving, and USART for SCADA or HMI panel communication. The industrial -40C to +85C temperature range handles factory floor environments. Its 4 MIPS throughput at 4 MHz is adequate for PID loop calculations at 100 Hz sample rates, while the 14KB OTP program memory stores control tables, calibration constants, and state machines. Unlike the flash-based PIC16F77, the OTP memory prevents field tampering of calibration data in safety-critical loops.
Recommandé
HVAC Climate Controllers
HVAC controllers benefit from the PIC16C77-04I/P's combination of 8 ADC channels (for temperature, humidity, and pressure sensors), PWM-capable CCP modules (for damper and valve actuator control), and a USART for connection to building management systems via Modbus or BACnet gateways. The 4 MHz clock is more than sufficient for thermostat loop times of 1-10 seconds. The 14KB program memory stores scheduling, setpoint profiles, and fault logging, while the industrial temperature range handles equipment-room environments. The OTP memory ensures firmware stability once deployed.
Recommandé
Small DC Motor and Stepper Control
The PIC16C77-04I/P's two CCP modules generate PWM outputs for driving small DC motors, fans, or unipolar stepper motors via simple MOSFET bridges. With 4 MIPS throughput and 33 I/O pins, it can manage H-bridge direction logic, current sensing via the ADC, and quadrature encoder feedback via external interrupt pins. The 8-channel ADC allows multiple motor currents or position sensors to be sampled sequentially. The OTP memory locks in calibration data such as current trip thresholds and acceleration ramps.
Recommandé
Educational and Hobbyist Microcontroller Boards
The PIC16C77-04I/P in 40-pin PDIP is ideal for educational microcontroller courses and hobbyist projects due to its through-hole package (easy to breadboard and socket), 40 pins providing ample I/O for learning, and well-documented PIC16 mid-range architecture taught in many university curricula. The 4 MHz ceramic resonator is forgiving for first-time clock bring-up. The 14KB program memory supports substantial student projects while the 35-instruction RISC instruction set is approachable for assembly learners. Students can migrate to PIC16F77 for in-circuit reprogrammability.
Recommandé
Sensor Signal Conditioning Front-Ends
Sensor front-end designs use the PIC16C77-04I/P's 8-channel 8-bit ADC for digitizing multiple analog sensors, USART for sending processed data to a host controller or PC, and 33 I/O pins for MUX switching or digital sensor selection. With 4 MIPS, the part can run basic linearization, averaging, and alarm threshold algorithms in firmware. The industrial temperature range suits outdoor sensor installations, while the OTP memory prevents inadvertent firmware modifications in deployed units. PIC16F77-I/P is recommended for new designs needing firmware updates.
Recommandé
Legacy Embedded Instrumentation
Maintaining legacy industrial instruments originally designed around PIC16C77-04I/P requires continued supply of this NRND part. The MCU's 33 I/O pins, USART for data output, and 8-channel ADC suit bench-top multimeters, panel meters, and process calibrators from the late 1990s. The OTP memory is acceptable for fixed-function instruments that never required firmware updates. For new instrumentation designs, PIC16F877A-I/P (40-pin PDIP, Flash, more memory) is the recommended Microchip migration path with same pinout and broader peripheral set.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC16C77-04I/P — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC16F77-I/P | PIC16C77-04/P | PIC16C765-I/P | PIC16C74B-04I/P |
|---|---|---|---|---|---|
| Package | 40-pin PDIP | 40-pin PDIP (same) | 40-pin PDIP (same) | 40-pin PDIP (same) | 40-pin PDIP (same) |
| Brand | Microchip Technology | Microchip Technology (same) | Microchip Technology (same) | Microchip Technology (same) | Microchip Technology (same) |
| Program Memory | 14 KB OTP | 14 KB Flash | 14 KB OTP | 14 KB OTP | 4 KB OTP |
| Maximum Clock | 4 MHz | 20 MHz | 4 MHz | 4 MHz | 4 MHz |
| RAM | 368 bytes | 368 bytes | 368 bytes | 368 bytes | 192 bytes |
| Memory Type | OTP EPROM | Flash (reprogrammable) | OTP EPROM | OTP EPROM | OTP EPROM |
| Temperature Range | -40C to +85C (Industrial) | -40C to +85C (Industrial) | 0C to +70C (Commercial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) |
| ADC Channels | 8 channels, 8-bit | 8 channels, 8-bit | 8 channels, 8-bit | 8 channels, 8-bit | 8 channels, 8-bit |
| Special Features | 33 I/O, USART, MSSP, 2 CCP | Same + Flash reprogrammability | Same peripherals | Same + USB 1.1 SIE, fewer I/O (24) | Same peripherals, less memory |
Principaux différenciateurs
- Industrial temperature range (-40C to +85C) in standard speed grade (vs PIC16C77-04/P)
- Recommended modern replacement is pin-compatible (vs PIC16F77-I/P)
- Higher memory configuration in same package (vs PIC16C74B-04I/P)
Notes de conception
OTP memory is one-time programmable - firmware must be 100% verified before programming, as mistakes cannot be erased. For development cycles, prototype with PIC16F77 (Flash) on the same PCB footprint, then move to PIC16C77-04I/P for production. A common pitfall is assuming the BOR (brown-out reset) voltage threshold matches the minimum VDD of 4.0V exactly - in practice it can vary, so design VDD to stay above 4.2V under all load conditions if BOR is enabled. The 'I' suffix denotes industrial -40C to +85C; commercial 'PIC16C77-04/P' without 'I' is 0C to +70C only.
Power supply decoupling requires a 0.1 uF ceramic capacitor placed within 5 mm of each VDD pin (pins 11 and 32 on PDIP-40), plus a bulk 10 uF electrolytic or tantalum on the main VDD rail. According to the PIC16C7X datasheet, VSS pins (12 and 31) should be tied to a low-impedance ground plane. For noise-sensitive ADC applications, an additional LC filter on AVdd (when implemented as separate analog supply) is recommended. Power-on reset (POR) requires VDD rise time below a specified threshold; if the rise is slower, use the MCLR pin with an external RC delay.
The 40-pin PDIP package at 0.600 inch row spacing (15.24 mm) suits through-hole PCB design with 2.54 mm (0.1 inch) pitch. For prototyping, use a 40-pin DIP socket (machined-pin preferred for reliability). When migrating to surface-mount, PIC16C77-04I/PT (TQFP-44) or PIC16C77-04I/L (PLCC-44) are footprint-compatible within the family but require PCB redesign. The crystal oscillator traces (OSC1/OSC2) should be kept short and surrounded by ground; for 4 MHz operation, ceramic resonators with built-in capacitors are a cost-effective alternative to crystals.
Informations de conformité
Lead-free and RoHS compliant per Microchip product page. Not AEC-Q100 qualified - for automotive applications consider PIC16F77-E/P or PIC18F variants with automotive qualification. Halogen-free status not explicitly stated in provided data.
