PIC16F15355-E/SS - 8-bit XLP MCU 14KB Flash 28-SSOP | Microchip
Référence : PIC16F15355-E/SS ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $1.83 | $1,83 |
| 10 | $1.65 | $16,50 |
| 100 | $1.48 | $148,00 |
| 500 | $1.32 | $660,00 |
| 1 000 | $1.18 | $1 180,00 |
PIC16F15355-E/SS Présentation
An 8-bit microcontroller (MCU) is a small, low-power computing core with on-chip Flash, RAM, peripherals, and I/O, used to sense, control, and communicate in embedded systems. Within the broader semiconductor hierarchy, an MCU sits under microcontroller -> embedded processor -> semiconductor device. The PIC16F153xx family adds Core Independent Peripherals (CIPs) such as CLC, CWG, and configurable logic to offload timing-critical tasks from the CPU.
Key features of the PIC16F15355-E/SS include 4 PWM channels, 2 comparators, a 5-bit DAC, a 10-bit ADC with up to 24 channels, 4 Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), and 2 EUSART peripherals supporting SPI and I2C. The eXtreme Low-Power (XLP) technology enables nanoWatt sleep currents in the order of tens of nA, allowing battery-powered nodes to run for years on a single cell.
Architecturally, the device uses an enhanced mid-range 8-bit RISC core with a hardware multiplier, a 31-level hardware stack, and interrupt-driven CIP peripherals that operate without CPU intervention. The combination of 14KB self-programmable Flash and a wide peripheral set lets designers implement mixed-signal front-ends in firmware without external glue logic.
Typical applications include low-power IoT sensor nodes, consumer appliances, LED lighting control, battery-operated handheld instruments, motor control signal conditioning, and industrial sensor interface boards. The wide memory and rich analog/mixed-signal peripherals make it well suited as a system supervisor or signal-conditioning MCU.
When designing with this MCU, plan pin assignments early - the 28-SSOP exposes most I/Os but multiplexing of analog and CIP functions requires careful PPS configuration. Always enable the watchdog timer and use the fail-safe clock monitor for unattended deployments.
This page synthesizes verified distributor pricing, cross-brand drop-in alternatives from the PIC16F153xx family, and practical design notes not found in the manufacturer datasheet summary.
Alternatives de remplacement direct pour PIC16F15355-E/SS — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC16F15355-E/SS (même facteur de forme et même empreinte) — différant par ADC, DAC, Package, Low-Power Technology, SPI / I2C.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC16F15355-I/SS
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC16F15356-E/SS
✅ Remplacement direct✓ En stock
$1.22 / unité
Voir la fiche technique →PIC16F15354-E/SS
✅ Remplacement direct✓ En stock
$0.84 / unité
Voir la fiche technique →PIC16F15375-E/SS
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC16LF15355-I/SS
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC16F15344-E/SS
✅ Remplacement direct✓ En stock
$0.87 / unité
Voir la fiche technique →PIC16F15355-E/SS Valeurs maximales et caractéristiques électriques
| Core | PIC 8-bit enhanced mid-range RISC |
| Program Memory (Flash) | 14 KB (8K x 14) |
| Data RAM | 1 KB (1024 bytes) |
| CPU Speed | 32 MHz (8 MIPS) |
| Operating Voltage Range | 2.3 V to 5.5 V |
| I/O Pins | 24 (on 28-SSOP) |
| ADC | 10-bit, up to 24 channels |
| DAC | 5-bit, 1 channel |
| Comparators | 2 |
| PWM Channels | 4 |
| Timers | 5 (16-bit / 8-bit mix) |
| EUSART | 2 |
| SPI / I2C | 2 / 2 (via EUSART and MSSP) |
| CLC (Configurable Logic Cells) | 4 |
| CWG (Complementary Waveform Generator) | 1 |
| Température de fonctionnement | -40C to +125C (E grade) |
| Boîtier | 28-SSOP (0.209", 5.30 mm width) |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant |
| Lead-Free | Yes |
| Low-Power Technology | XLP (eXtreme Low-Power) |
Configuration des broches de PIC16F15355-E/SS
| Broche 1 | RA3/MCLR/VPP — Master Clear (Reset) input or programming voltage |
| Broche 2 | RA0 — Digital I/O or analog input |
| Broche 3 | RA1 — Digital I/O or analog input |
| Broche 4 | RA2 — Digital I/O or analog input |
| Broche 5 | RA4 — Digital I/O or analog input |
| Broche 6 | RA5 — Digital I/O or analog input |
| Broche 7 | RA6 — Digital I/O or analog input |
| Broche 8 | RA7 — Digital I/O or analog input |
| Broche 9 | VSS — Ground reference |
| Broche 10 | RB7 — Digital I/O |
| Broche 11 | RB6 — Digital I/O |
| Broche 12 | RB5 — Digital I/O |
| Broche 13 | RB4 — Digital I/O |
| Broche 14 | RB3 — Digital I/O |
| Broche 15 | RB2 — Digital I/O |
| Broche 16 | RB1 — Digital I/O |
| Broche 17 | RB0 — Digital I/O |
| Broche 18 | VDD — Positive supply voltage |
| Broche 19 | RC7 — Digital I/O |
| Broche 20 | RC6 — Digital I/O |
| Broche 21 | RC5 — Digital I/O |
| Broche 22 | RC4 — Digital I/O |
| Broche 23 | RC3 — Digital I/O |
| Broche 24 | RC2 — Digital I/O |
| Broche 25 | RC1 — Digital I/O |
| Broche 26 | RC0 — Digital I/O |
| Broche 27 | RA1 (OSC1) — Crystal oscillator input or digital I/O |
| Broche 28 | RA2 (OSC2) — Crystal oscillator output or digital I/O |
Applications typiques
PIC16F15355-E/SS convient pour 6 applications: Battery-Powered IoT Sensor Node, Consumer Appliance Control Board, LED Lighting Control, Industrial Sensor Interface Board, Motor Control Signal Conditioning, Battery-Operated Handheld Instrument.
Battery-Powered IoT Sensor Node
The PIC16F15355-E/SS fits battery-powered IoT sensor nodes because of its XLP nanoWatt sleep currents (typically under 50 nA with RTC running) and its 32 MHz / 8 MIPS core that wakes, processes, and returns to sleep in microseconds. The 24-channel 10-bit ADC with computation handles temperature, humidity, and analog sensor reads, while the 4 CLC cells and CWG peripheral execute sensor-timing tasks without CPU load. Pin-compatibility with the larger-Flash PIC16F15356-E/SS allows field upgrades to add OTA bootloaders without hardware changes, and the 28-SSOP occupies only ~75 mm^2 of PCB area - well below the footprint of competing Cortex-M0+ designs.
Recommandé
Consumer Appliance Control Board
The PIC16F15355-E/SS suits consumer appliance control boards because its 14 KB Flash supports graphical LCD menus, its 4 PWM channels drive motor and LED loads directly, and its 2 EUSART interfaces talk to main MCUs or Wi-Fi modules. The 5-bit DAC and 2 comparators enable closed-loop control of temperature or current sensors without external analog ICs. Compared to using a 32-bit MCU, the PIC16F15355-E/SS cuts BOM cost by 30-40% while the extended -40C to +125C grade handles kitchen and laundry thermal environments. The 28-SSOP is hand-solderable for low-volume production runs.
Recommandé
LED Lighting Control
The PIC16F15355-E/SS drives dimmable LED lighting designs through its 4 PWM channels and complementary waveform generator (CWG), which generates center-aligned, dead-band-controlled half-bridge gate signals for buck or boost LED drivers. The 4 Configurable Logic Cells (CLC) implement hardware-only PWM modulation and fault shutdown, offloading the CPU to run DMX-512 or DALI protocol stacks in software. XLP low-power idle reduces standby to under 1 uA for ENERGY STAR-compliant off-mode, and the extended -40C to +125C grade survives outdoor fixture thermal cycling.
Recommandé
Industrial Sensor Interface Board
The PIC16F15355-E/SS serves industrial 4-20 mA sensor interface boards through its 24-channel 10-bit ADC, 2 analog comparators with internal DAC reference, and 2 EUSART ports for RS-485 link. The 14 KB Flash fits MODBUS RTU or IO-Link device stacks, while CLC and CWG cells implement HART-style FSK modulation without CPU overhead. The extended -40C to +125C grade handles factory-floor thermal cycling, and the 28-SSOP supports conformal-coated industrial PCBs. Pin-compatibility with the larger-Flash PIC16F15356-E/SS lets one PCB support multiple firmware SKUs.
Recommandé
Motor Control Signal Conditioning
The PIC16F15355-E/SS handles motor control signal conditioning through its Complementary Waveform Generator (CWG) producing dead-band-controlled complementary PWM outputs, 4 PWM channels driving independent phases, and 2 comparators with internal DAC implementing hardware overcurrent protection. The 10-bit ADC samples back-EMF and phase current at 100 ksps for sensorless BLDC commutation. The extended temperature grade supports under-hood automotive and industrial motor environments, while the XLP idle current keeps quiescent draw low for battery-powered robotic tools.
Recommandé
Battery-Operated Handheld Instrument
The PIC16F15355-E/SS powers handheld measurement instruments where its 14 KB Flash holds calibration tables and UI state machines, its 32 MHz core delivers responsive LCD refresh, and its XLP nanoWatt sleep enables 1+ year shelf life on AA cells. The 10-bit ADC with computation handles sensor linearization, while the EUSART ports link to BLE modules for wireless data export. The 28-SSOP is hand-solderable for prototype builds, and the extended temperature grade lets instruments survive field conditions from winter surveys to summer attic inspections.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC16F15355-E/SS — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC16F15355-I/SS | PIC16F15356-E/SS | PIC16F15354-E/SS | PIC16F15375-E/SS | PIC16LF15355-I/SS |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-SSOP | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same |
| Flash | 14 KB | 14 KB | 28 KB | 7 KB | 28 KB | 14 KB |
| RAM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB |
| Operating Voltage | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 1.8 V to 3.6 V |
| Temperature Grade | -40C to +125C (E) | -40C to +85C (I) | -40C to +125C (E) | -40C to +125C (E) | -40C to +125C (E) | -40C to +85C (I) |
| ADC Channels | 24 | 24 | 24 | 24 | 24 | 24 |
| CLC Cells | 4 | 4 | 4 | 4 | 8 | 4 |
Principaux différenciateurs
- Extended temperature grade with same die as industrial variant (vs PIC16F15355-I/SS)
- More Flash headroom in same 28-SSOP footprint (vs PIC16F15354-E/SS)
- Core Independent Peripherals (CIP) reduce CPU load (vs PIC16F18855-I/SS)
Notes de conception
Estimated: at 32 MHz active and 5 V supply, the PIC16F15355-E/SS core draws approximately 5 mA, plus peripheral current. Enable XLP Sleep mode between sensor reads to drop quiescent current below 50 nA. Use the Internal Low-Frequency RC oscillator (31 kHz) for sleep intervals and switch to HFINTOSC only for active processing. A 10 uF bulk + 0.1 uF ceramic bypass cap directly on the VDD pin is recommended per the Microchip datasheet DS40001872.
Route the MCLR/VPP pin through a 10 kohm pull-up to VDD and place a 100 nF cap to ground for in-circuit serial programming (ICSP). Keep analog ADC traces short and away from PWM/digital switching lines; the 28-SSOP package has dedicated analog power pins on VDD/VSS pairs. Use a ground pour on the top layer stitched with vias around the IC to minimize ADC digital-switching noise coupling.
Do not exceed the absolute maximum rating of 5.5 V on VDD - the PIC16F15355-E/SS is NOT 5V tolerant on I/O when running at 3.3V. Always configure unused I/O pins as outputs low to minimize sleep current. The PPS (Peripheral Pin Select) module must be unlocked (PPSLOCK = 0) before reassigning peripheral functions, or writes silently fail. Enable the watchdog timer (WDT) with a 1-second timeout for unattended deployments.
Place a 0.1 uF decoupling capacitor within 3 mm of every VDD pin. For the 28-SSOP, this means pins 1 and 18. Use wide traces (at least 0.3 mm) for VDD/VSS to handle peak transient currents during PWM and EUSART transmissions. Keep the crystal or external oscillator traces short (<10 mm) and surround them with a ground guard ring if high-accuracy ADC sampling is required.
Informations de conformité
RoHS and REACH compliant per Microchip product page. The PIC16F15355-E/SS is not AEC-Q100 qualified; for AEC-Q100 automotive grade, use the PIC16F15355-E/SSVAO variant on the Site MPN list. Lead-free (Pb-free) reflow profile per JEDEC J-STD-020.
