PIC16LF15344-E/SO - 8-bit XLP MCU, 7KB Flash, 32MHz | Microchip
Référence : PIC16LF15344-E/SO ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $1.42 | $1,42 |
| 10 | $1.31 | $13,10 |
| 100 | $1.17 | $117,00 |
| 500 | $1.04 | $520,00 |
| 1 000 | $0.94 | $940,00 |
| 3 000 | $0.82 | $2 460,00 |
PIC16LF15344-E/SO Présentation
What is an 8-bit microcontroller? An 8-bit microcontroller (MCU) is a small computer on a single integrated circuit containing an 8-bit CPU core, Flash program memory, SRAM data memory, and a rich set of on-chip peripherals. PIC microcontrollers sit within the broader hierarchy: PIC microcontroller -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. The 'LF' prefix indicates the low-voltage 'F' (Flash) process node, allowing operation down to 1.8V and enabling battery-friendly XLP operation.
Key features of the PIC16LF15344 include four 10-bit PWMs with complementary waveform generation, a hardware 5-bit/8-bit DAC, an analog comparator, a 10-bit ADC with computation, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), two EUSART modules, and SPI/I2C interfaces. The XLP variant offers nanoWatt XLP sleep currents typically below 50 nA in Sleep with peripherals off.
Architecturally the device is built on an enhanced mid-range 8-bit core supporting 49 instructions and a 16-level hardware stack, with a 32 MHz internal oscillator that eliminates the need for an external crystal in most designs. Core Independent Peripherals (CIPs) such as the CLC, CWG, and NCO allow hardware-driven state machines without CPU intervention, reducing power and code footprint.
Typical applications include battery-powered IoT sensor nodes, low-power wireless remotes, white goods and HMI controls, LED lighting controllers, automotive body and accessory electronics, and consumer devices requiring small pin-count XLP solutions. Designers choose it when code size, peripheral count, and ultra-low sleep current must coexist in a 20-pin footprint.
When designing with this MCU, follow the Microchip MPLAB X IDE toolchain and configure the configuration bits carefully for the chosen oscillator and watchdog. Decouple VDD with a 100 nF capacitor close to the pin, and route MCLR through the recommended 10 kohm pull-up if external reset is required.
This page synthesizes distributor pricing, parametric comparison data, and practical design notes not consolidated in any single distributor listing.
Alternatives de remplacement direct pour PIC16LF15344-E/SO — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC16LF15344-E/SO (même facteur de forme et même empreinte) — différant par DAC, PWM Channels, ADC, Comparators, I/O Pins.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC16F15344-E/SO
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$0.86 / unité
Voir la fiche technique →PIC16LF15324-E/SO
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
PIC16F15324-E/SO
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
PIC16LF15345-E/SO
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$1.08 / unité
Voir la fiche technique →PIC16F15344T-I/SO
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
PIC16LF15344-E/SO Valeurs maximales et caractéristiques électriques
| Product Family | PIC16F (PIC® XLP™ 16F) |
| Core Architecture | 8-bit enhanced mid-range |
| Program Memory (Flash) | 7 KB (4K x 14 words) |
| Data SRAM | 512 B |
| Maximum CPU Frequency | 32 MHz |
| Operating Voltage Range | 1.8 V to 3.6 V |
| Number of I/O Pins | 18 |
| ADC | 10-bit |
| DAC | 5-bit / 8-bit hardware DAC |
| PWM Channels | 4 (10-bit) |
| Comparators | Yes |
| Configurable Logic Cells (CLC) | 4 |
| Complementary Waveform Generator (CWG) | Yes |
| EUSART Modules | 2 |
| SPI / I2C | Yes / Yes |
| Boîtier | 20-pin SOIC (7.50 mm width, tube) |
| Type de montage | Surface Mount |
| Plage de température de fonctionnement | -40C to +125C (E suffix) |
| Statut RoHS | Compliant |
| Lead-Free | Yes |
| Niveau MSL | 1 |
Configuration des broches de PIC16LF15344-E/SO
| Broche 1 | RA5 — Bidirectional I/O with interrupt-on-change, alternate functions include CWG input and DAC reference |
| Broche 2 | RA4 — Bidirectional I/O, alternate function: CLC output, timer gate input |
| Broche 3 | RA3 — Bidirectional I/O, alternate function: MCLR (input only when configured) |
| Broche 4 | RA2 — Bidirectional I/O, alternate function: analog input AN2 and DAC output |
| Broche 5 | RA1 — Bidirectional I/O, alternate function: analog input AN1 and comparator reference |
| Broche 6 | RA0 — Bidirectional I/O, alternate function: analog input AN0 and ICSPDAT |
| Broche 7 | VSS — Ground reference |
| Broche 8 | RA7 — Bidirectional I/O, alternate function: oscillator output or CLC input |
| Broche 9 | RA6 — Bidirectional I/O, alternate function: oscillator input or CLC input |
| Broche 10 | RC0 — Bidirectional I/O, alternate function: analog input AN4 and PWM output |
| Broche 11 | RC1 — Bidirectional I/O, alternate function: analog input AN5 and PWM output |
| Broche 12 | RC2 — Bidirectional I/O, alternate function: analog input AN6 and PWM output |
| Broche 13 | RC3 — Bidirectional I/O, alternate function: analog input AN7 and PWM output |
| Broche 14 | RC4 — Bidirectional I/O, alternate function: I2C/SPI data line and CLC output |
| Broche 15 | RC5 — Bidirectional I/O, alternate function: I2C clock and CLC output |
| Broche 16 | RC6 — Bidirectional I/O, alternate function: EUSART TX and SPI clock |
| Broche 17 | RC7 — Bidirectional I/O, alternate function: EUSART RX and SPI data input |
| Broche 18 | VSS — Ground reference (second VSS pin for power dissipation) |
| Broche 19 | VDD — Positive power supply (1.8 V to 3.6 V) |
| Broche 20 | VDDIO — I/O supply voltage, typically tied to VDD |
Applications typiques
PIC16LF15344-E/SO convient pour 6 applications: Battery-Powered IoT Sensor Node, Wireless Remote Control (HID / Consumer), White Goods and HMI Control, LED Lighting Controller, Automotive Body and Accessory Module, Industrial Sensor and Process Transmitter.
Battery-Powered IoT Sensor Node
The PIC16LF15344-E/SO is well suited for battery-powered IoT sensor nodes that spend most of their time in sleep and wake briefly to transmit. With XLP technology delivering nanoWatt sleep currents (typically below 50 nA) and a wide 1.8 V to 3.6 V operating range, this MCU can run directly from a single CR2032 coin cell or two AAA cells for months or years. The 10-bit ADC with computation performs on-chip sensor averaging without waking the CPU, while the four CLCs implement hardware state machines for wake-on-event signaling. The two EUSARTs enable simultaneous sensor-bus and radio-module communication, reducing external component count and bill of materials in compact IoT designs.
Recommandé
Wireless Remote Control (HID / Consumer)
The PIC16LF15344-E/SO is an excellent fit for low-power wireless remote controls such as TV remotes, key fobs, and presentation clickers. Its 32 MHz core runs the application code and a transmit routine for sub-GHz or IR LED drivers in microseconds, then drops back to sleep for months on a coin cell. The Complementary Waveform Generator (CWG) directly drives half-bridge or full-bridge MOSFETs for IR or piezo loads, offloading timing-critical waveform generation from the CPU. Two EUSARTs allow debug logging and main-link communication simultaneously, while the 18 I/O pins handle button matrix scanning and LED feedback without external glue logic.
Recommandé
White Goods and HMI Control
The PIC16LF15344-E/SO drives user interface panels on white goods such as washing machines, dishwashers, and ovens. The 32 MHz core handles capacitive-touch scanning, LED dimming, and seven-segment display refresh via the four PWM channels and four CLCs. The CWG generates complementary PWM outputs for synchronous motor or Triac drive signals, eliminating firmware timing jitter. Industrial-grade -40C to +125C operation ensures reliability inside hot appliance enclosures. XLP sleep modes let the MCU sit idle between user interactions with negligible battery drain for clock backup or end-of-cycle memory retention.
Recommandé
LED Lighting Controller
The PIC16LF15344-E/SO controls constant-current LED drivers in architectural lighting, RGB strips, and horticultural fixtures. Its four 10-bit PWM channels with complementary outputs provide smooth dimming without flicker, while the CWG generates high-frequency switching waveforms for synchronous buck or boost LED driver topologies. The 1.8 V to 3.6 V supply range simplifies designs powered by 3.3 V rails or single-cell Li-ion battery packs, while XLP technology keeps standby current below 50 nA when the lighting is off. The hardware DAC produces reference voltages for closed-loop current control, and the 10-bit ADC reads photodiode or thermistor feedback for daylight harvesting and thermal protection.
Recommandé
Automotive Body and Accessory Module
The PIC16LF15344-E/SO operates in non-safety automotive body electronics such as interior lighting controllers, seat heaters, and accessory power modules. The extended -40C to +125C temperature range and eXtreme Low-Power XLP technology support always-on modules that draw microamps during key-off. The CWG module generates complementary gate-drive signals for half-bridge drivers controlling seat heater elements or fan motors. Dual EUSARTs allow simultaneous LIN-bus communication and diagnostics over UART. Designers should note that the E temperature grade suffix is industrial-grade; automotive-grade AEC-Q100 qualified variants may be selected from the same PIC16LF15344 family for safety-relevant systems.
Recommandé
Industrial Sensor and Process Transmitter
The PIC16LF15344-E/SO acts as the local controller in 4-20 mA loop-powered or battery-backed industrial sensor transmitters. The 10-bit ADC with computation oversamples sensor signals for noise reduction, while the 5-bit/8-bit DAC generates the 4-20 mA loop current under closed-loop software control. XLP operation below 1 mA active current suits energy-harvesting or loop-powered transmitters with strict power budgets. Two EUSARTs and SPI/I2C enable simultaneous HART-modem communication and digital sensor interfacing. The industrial -40C to +125C temperature grade ensures operation in factory automation cabinets and outdoor instrumentation.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC16LF15344-E/SO — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC16F15344-E/SO | PIC16LF15324-E/SO | PIC16F15324-E/SO | PIC16LF15345-E/SO | PIC16F15344T-I/SO |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | SOIC-20 | SOIC-20 (same) | SOIC-20 (same) | SOIC-20 (same) | SOIC-20 (same) | SOIC-20 (same) |
| Program Flash | 7 KB | 7 KB (same) | 7 KB (same) | 7 KB (same) | 14 KB (+100%) | 7 KB (same) |
| SRAM | 512 B | 512 B (same) | 512 B (same) | 512 B (same) | 1 KB (+100%) | 512 B (same) |
| Operating Voltage | 1.8 V to 3.6 V | 2.3 V to 5.5 V | 1.8 V to 3.6 V (same) | 2.3 V to 5.5 V | 1.8 V to 3.6 V (same) | 2.3 V to 5.5 V |
| CLC Cells | 4 | 4 (same) | 1 (-75%) | 1 (-75%) | 4 (same) | 4 (same) |
| EUSART Modules | 2 | 2 (same) | 1 (-50%) | 1 (-50%) | 2 (same) | 2 (same) |
| Temperature Grade | -40C to +125C (E) | -40C to +125C (E) | -40C to +125C (E) | -40C to +125C (E) | -40C to +125C (E) | -40C to +85C (I) |
Principaux différenciateurs
- Highest CLC count in the PIC16(L)F153xx SOIC-20 family (vs PIC16LF15324-E/SO)
- Dual EUSART versus single EUSART in the 15324 variant (vs PIC16LF15324-E/SO)
- Low-voltage XLP support down to 1.8 V (vs PIC16F15344-E/SO)
Notes de conception
The PIC16LF15344-E/SO requires a single 100 nF ceramic decoupling capacitor placed within 3 mm of the VDD pin (pin 19) and VSS pin (pin 18). According to the Microchip datasheet, VDDIO (pin 20) should be tied to VDD through its own short trace; tie VSS pins together at the package. For low-noise analog performance, add a 10 uF bulk capacitor near the MCU and a small ferrite bead on the analog supply if the design shares the rail with switching converters.
When migrating between the PIC16LF15344 (1.8 V to 3.6 V) and the PIC16F15344 (2.3 V to 5.5 V), verify that all I/O peripherals and sensors tolerate the lower VDD on the LF variant. Some 5 V sensors will not register logic-high at 1.8 V. The configuration bits for oscillator selection, watchdog timer, and code protection must be set in the IDE; an incorrect WDTE setting can cause unintended resets in field-deployed units.
Place the MCU so that the SOIC package's exposed copper pour is connected to a quiet ground plane. According to the Microchip datasheet, the 20-pin SOIC is a single-row package with no thermal pad; ensure wide VDD and VSS traces (at least 0.4 mm) and keep high-speed switching traces away from the analog pins RA0-RA2 to avoid ADC crosstalk. Decoupling capacitors should use short, direct vias to the ground plane.
Informations de conformité
RoHS and REACH compliant per Microchip product page. Not AEC-Q100 qualified - this is the industrial-grade E suffix variant. AEC-Q100 versions exist in the same PIC16LF15344 family for automotive applications.
