PIC16LF19196T-I/MR - 8-bit XLP MCU 32MHz 28KB Flash 64-QFN | Microchip
Référence : PIC16LF19196T-I/MR ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $3.85 | $3,85 |
| 10 | $3.47 | $34,70 |
| 100 | $3.08 | $308,00 |
| 500 | $2.78 | $1 390,00 |
| 1 000 | $2.49 | $2 490,00 |
PIC16LF19196T-I/MR Présentation
An 8-bit microcontroller (MCU) is a single-chip processor with an 8-bit data path, integrated program memory, RAM, and peripherals intended for embedded control tasks. The PIC16 family sits within the broader taxonomy MCU -> microcontroller -> embedded processor -> integrated circuit -> semiconductor. Within Microchip's portfolio the PIC16LF191xx family adds Core Independent Peripherals (CIPs) and an integrated LCD segment driver with charge pump, targeting low-power battery-driven HMIs.
Key features include the integrated 12-bit ADC2 with computation, a 5-bit DAC, two analog comparators with programmable reference, configurable logic cells (CLC), Complementary Waveform Generator (CWG), Capture/Compare/PWM (CCP) and PWM modules, Zero-Cross Detect (ZCD), Real-Time Clock/Calendar (RTCC) and Peripheral Pin Select (PPS). The device also integrates 256 bytes of EEPROM data memory and supports hardware Limit Timer (HLT) and Windowed Watchdog Timer (WWDT).
The PIC16LF19196 architecture uses a RISC-style 14-bit instruction word with a 32-level hardware stack and an instruction-cycle-time of four clock periods, yielding 8 MIPS per MHz. The integrated charge pump and LCD driver allow glass bias generation from a single low-voltage rail without external boost components, simplifying BOM count for battery powered meter and appliance displays.
Typical applications include battery powered LCD meters, thermostat and HVAC control panels, portable medical monitors, IoT sensor nodes with segment displays, white goods user interfaces, and remote controls with capacitive touch buttons. The 1.8V minimum Vdd enables single-cell Li-coin or 2x AA-alkaline designs where energy budget is critical.
When designing with this part, choose the LF (low-voltage) variant only if the supply rail will not exceed 3.6V. For 5V-tolerant systems use the PIC16F19196 (5V) variant instead. The 64-QFN package has an exposed pad that must be soldered to the ground plane for thermal and electrical performance per the Microchip datasheet.
This page synthesizes distributor pricing for PIC16LF19196T-I/MR, same-family drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.
Alternatives de remplacement direct pour PIC16LF19196T-I/MR — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC16LF19196T-I/MR (même facteur de forme et même empreinte) — différant par ADC, MSL Level, Package, LCD Driver, CPU Speed.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC16LF19195T-I/MR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC16LF19197T-I/MR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC16F19196T-I/MR
✅ Remplacement direct✓ En stock
$1.72 / unité
Voir la fiche technique →PIC16LF19196-E/MR
✅ Remplacement direct✓ En stock
$1.78 / unité
Voir la fiche technique →PIC16LF19196T-I/MR Valeurs maximales et caractéristiques électriques
| Product Family | PIC16 (8-bit RISC, 14-bit instruction word) |
| Series | PIC16LF191xx (XLP, LCD) |
| Core | PIC16 8-bit |
| CPU Speed | 32 MHz (8 MIPS) |
| Program Memory (Flash) | 28 KB (16K x 14 words) |
| Data SRAM | 2 KB |
| Data EEPROM | 256 bytes |
| Supply Voltage (Vdd) | 1.8 V to 3.6 V |
| Température de fonctionnement | -40 C to +85 C (industrial grade) |
| Boîtier | 64-lead QFN (9x9 mm) |
| Type de montage | Surface Mount |
| ADC | 12-bit ADC2 with computation |
| DAC | 5-bit DAC |
| Comparators | 2 with programmable reference |
| LCD Driver | Integrated with charge pump |
| PWM / CCP / CWG | PWM, CCP, Complementary Waveform Generator |
| Special Peripherals | CLC, PPS, ZCD, RTCC, HLT, WWDT |
| Niveau MSL | MSL3 (per JEDEC J-STD-020) |
| Statut RoHS | Compliant |
| Lead-Free | Yes |
Configuration des broches de PIC16LF19196T-I/MR
| Broche 1 | RB7 — PORTB digital I/O |
| Broche 2 | RB6 — PORTB digital I/O / ICSPCLK |
| Broche 3 | RB5 — PORTB digital I/O |
| Broche 4 | RB4 — PORTB digital I/O |
| Broche 5 | RB3 — PORTB digital I/O |
| Broche 6 | RB2 — PORTB digital I/O |
| Broche 7 | RB1 — PORTB digital I/O |
| Broche 8 | RB0 — PORTB digital I/O / interrupt |
| Broche 9 | VDD — Positive supply |
| Broche 10 | VSS — Ground reference |
| Broche 11 | RC7 — PORTC digital I/O |
| Broche 12 | RC6 — PORTC digital I/O |
| Broche 13 | RC5 — PORTC digital I/O |
| Broche 14 | RC4 — PORTC digital I/O |
| Broche 15 | RC3 — PORTC digital I/O / SCL |
| Broche 16 | RC2 — PORTC digital I/O / SDA |
| Broche 17 | RC1 — PORTC digital I/O |
| Broche 18 | RC0 — PORTC digital I/O |
| Broche 19 | RA7 — PORTA digital I/O |
| Broche 20 | RA6 — PORTA digital I/O |
| Broche 21 | RA5 — PORTA digital I/O |
| Broche 22 | RA4 — PORTA digital I/O |
| Broche 23 | RA3 — PORTA digital I/O / MCLR |
| Broche 24 | RA2 — PORTA digital I/O |
| Broche 25 | RA1 — PORTA digital I/O |
| Broche 26 | RA0 — PORTA digital I/O |
| Broche 27 | VSS — Ground reference |
| Broche 28 | VDD — Positive supply |
| Broche 29 | RD7 — PORTD digital I/O |
| Broche 30 | RD6 — PORTD digital I/O |
| Broche 31 | RD5 — PORTD digital I/O |
| Broche 32 | RD4 — PORTD digital I/O |
| Broche 33 | RD3 — PORTD digital I/O |
| Broche 34 | RD2 — PORTD digital I/O |
| Broche 35 | RD1 — PORTD digital I/O |
| Broche 36 | RD0 — PORTD digital I/O |
| Broche 37 | RE7 — PORTE digital I/O |
| Broche 38 | RE6 — PORTE digital I/O |
| Broche 39 | RE5 — PORTE digital I/O |
| Broche 40 | RE4 — PORTE digital I/O |
| Broche 41 | RE3 — PORTE digital I/O |
| Broche 42 | RE2 — PORTE digital I/O |
| Broche 43 | RE1 — PORTE digital I/O |
| Broche 44 | RE0 — PORTE digital I/O |
| Broche 45 | RF7 — PORTF digital I/O / LCD SEG |
| Broche 46 | RF6 — PORTF digital I/O / LCD SEG |
| Broche 47 | RF5 — PORTF digital I/O / LCD SEG |
| Broche 48 | RF4 — PORTF digital I/O / LCD SEG |
| Broche 49 | RF3 — PORTF digital I/O / LCD SEG |
| Broche 50 | RF2 — PORTF digital I/O / LCD SEG |
| Broche 51 | RF1 — PORTF digital I/O / LCD SEG |
| Broche 52 | RF0 — PORTF digital I/O / LCD SEG |
| Broche 53 | RG7 — PORTG digital I/O / LCD SEG |
| Broche 54 | RG6 — PORTG digital I/O / LCD SEG |
| Broche 55 | RG5 — PORTG digital I/O / LCD SEG |
| Broche 56 | RG4 — PORTG digital I/O / LCD SEG |
| Broche 57 | RG3 — PORTG digital I/O / LCD SEG |
| Broche 58 | RG2 — PORTG digital I/O / LCD SEG |
| Broche 59 | RG1 — PORTG digital I/O / LCD SEG |
| Broche 60 | RG0 — PORTG digital I/O / LCD SEG |
| Broche 61 | AVSS — Analog ground |
| Broche 62 | AVDD — Analog supply |
| Broche 63 | VCAP — Voltage regulator bypass capacitor |
| Broche 64 | EP — Exposed pad - connect to VSS |
Applications typiques
PIC16LF19196T-I/MR convient pour 6 applications: Battery Powered LCD Meter, Thermostat and HVAC Control Panel, Portable Medical Monitor, IoT Sensor Node with Segment Display, White Goods User Interface, Remote Control with Capacitive Touch.
Battery Powered LCD Meter
The PIC16LF19196T-I/MR's 1.8V-3.6V wide supply and integrated LCD segment driver with on-chip charge pump make it ideal for battery powered electricity, water, or gas meters. The integrated charge pump generates glass bias voltages (typically 3V-5V) from a single 3V coin cell without external boost components, reducing BOM count by 4-6 parts. XLP nanoWatt sleep currents below 100 nA extend coin-cell life to 10+ years in metrology duty cycles.
Recommandé
Thermostat and HVAC Control Panel
The PIC16LF19196T-I/MR's 28KB Flash, integrated 12-bit ADC2, and PWM peripherals suit thermostat and HVAC controller designs that need to read temperature sensors, drive TRIACs, and display status on segmented LCD. The ADC2 with computation automates averaging and threshold detection in hardware, offloading the CPU. CLC and CWG enable dead-band control of complementary power stages for synchronous motor or PFC drive.
Recommandé
Portable Medical Monitor
The PIC16LF19196T-I/MR suits portable medical monitoring devices such as pulse oximeters, glucometers, and blood pressure cuffs that need low-power analog front ends and segmented LCD output. The 12-bit ADC2 with computation provides automated oversampling and threshold detection required for vital-sign sensor front ends, while the XLP sleep modes keep average current below 5 uA for multi-day battery operation on a single CR2032 cell.
Recommandé
IoT Sensor Node with Segment Display
The PIC16LF19196T-I/MR combines eXtreme Low-Power XLP sleep modes (down to 30 nA in Retention mode) with Core Independent Peripherals that wake the CPU only on sensor threshold events. The integrated LCD driver displays readings without an external display controller, while ZCD and RTCC allow line-powered or battery duty-cycled operation. PPS enables flexible pin remapping for compact 4-layer PCB layouts.
Recommandé
White Goods User Interface
The PIC16LF19196T-I/MR powers the LCD user interface of washing machines, dishwashers, and ovens that need 30-50 segment displays plus motor/relay control. The CWG, PWM, and CCP modules drive brushless DC or universal motors directly, while the LCD charge pump drives TN/STN glass. The industrial -40C to +85C temperature grade handles appliance thermal stress near motors and heaters.
Recommandé
Remote Control with Capacitive Touch
The PIC16LF19196T-I/MR with mTouch capacitive touch sensing library and integrated LCD output suits remote controls that need 10-20 touch buttons plus a multi-segment status display. The CTMU peripheral provides hardware capacitive touch measurement with sub-10 pF resolution, and the ADC2 reads battery voltage for low-battery warning. PPS enables PCB routing flexibility for compact remote-control form factors.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC16LF19196T-I/MR — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC16LF19196T-I/PT | PIC16LF19195T-I/MR | PIC16LF19197T-I/MR | PIC16F19196T-I/MR | PIC16LF19196-E/MR |
|---|---|---|---|---|---|---|
| Package | 64-QFN (9x9) | TQFP-64 | 64-QFN (9x9) - same | 64-QFN (9x9) - same | 64-QFN (9x9) - same | 64-QFN (9x9) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | PIC16 8-bit | PIC16 8-bit | PIC16 8-bit | PIC16 8-bit | PIC16 8-bit | PIC16 8-bit |
| CPU Speed | 32 MHz (8 MIPS) | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 28 KB (16K x 14) | 28 KB | 14 KB | 56 KB | 28 KB | 28 KB |
| SRAM | 2 KB | 2 KB | 1 KB | 4 KB | 2 KB | 2 KB |
| EEPROM | 256 bytes | 256 bytes | 256 bytes | 256 bytes | 256 bytes | 256 bytes |
| Operating Voltage | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 2.3 V to 5.5 V | 1.8 V to 3.6 V |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +125 C |
| LCD Driver | Integrated with charge pump | Integrated with charge pump | Integrated with charge pump | Integrated with charge pump | Integrated with charge pump | Integrated with charge pump |
Principaux différenciateurs
- Lowest-voltage variant in PIC16F19196 family with 1.8V minimum (vs PIC16F19196T-I/MR)
- 28KB Flash offers balanced memory versus cost (vs PIC16LF19195T-I/MR)
- Extended temperature grade available as drop-in -E variant (vs PIC16LF19196T-I/MR (industrial))
- Upward-compatible memory upgrade to 56KB Flash (vs PIC16LF19196T-I/MR)
Notes de conception
The 64-QFN package has a thermal resistance (theta_JA) of approximately 32 C/W on a standard 4-layer JEDEC test board. The exposed pad (pin 64) MUST be soldered to the PCB ground plane with thermal vias to keep junction temperature within the -40C to +85C industrial range. Estimated: at full 32 MHz CPU load and all peripherals active, core current is approximately 6 mA at 3.3V, yielding 20 mW dissipation and a 0.6 C junction rise - well within thermal limits. However, charge-pump load from a large LCD glass can add 1-3 mA continuously, increasing dissipation to 30 mW with a 1 C rise above ambient.
Place decoupling capacitors (100 nF ceramic + 10 uF bulk) within 3 mm of each VDD pin pair (pins 9/10, 27/28, 61/62). The VCAP pin (pin 63) requires a 1 uF to 10 uF ceramic bypass with ESR < 100 milliohm. Route analog AVSS/AVDD pairs separately from digital supplies with a star-ground topology to avoid ADC2 noise injection. Per datasheet DS40001974, place the VCAP cap on the same side as the IC with no via between pin and capacitor pad.
The PIC16LF19196T-I/MR supports multiple XLP sleep modes: Sleep mode at < 50 nA typical, Retention mode at < 100 nA with RAM preserved, and Deep Sleep mode with RTCC active at < 500 nA. For battery-powered LCD meters, use Sleep mode between LCD refreshes and wake the RTCC every 250 ms to update the display. Estimated: 1.5 V CR2032 capacity of 220 mAh divided by 5 uA average current yields approximately 5 years of operation - confirm by integrating the actual application duty cycle.
Do not connect MCLR (RA3, pin 23) directly to VDD without a series resistor - lightning/ESD transients can exceed the absolute maximum rating. Use a 10 kohm pull-up and a diode clamp. Do not exceed VDD + 0.3V on any I/O pin including RA3 when configured as MCLR. For in-circuit programming, add a 100 ohm series resistor on ICSPCLK (RB6) to limit programming current into the debugger. Programming voltage must be removed before normal operation begins.
Informations de conformité
RoHS compliant per Microchip product page. AEC-Q100 not qualified - choose PIC16F19196-E/MR for automotive-grade applications. JEDEC J-STD-020 MSL3 moisture sensitivity.
