PIC17LC752T-08I/L - 8-bit 8MHz 16KB OTP MCU 68-PLCC | Microchip
Référence : PIC17LC752T-08I/L ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $6.23 | $6,23 |
| 10 | $5.85 | $58,50 |
| 100 | $5.32 | $532,00 |
| 500 | $4.79 | $2 395,00 |
| 1 000 | $4.35 | $4 350,00 |
PIC17LC752T-08I/L Présentation
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and a configurable set of peripheral interfaces. PIC microcontrollers use a Harvard RISC architecture with separate program and data buses, positioning them in the hierarchy: PIC17 -> PIC microcontroller -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The PIC17C/LC family sits at the high end of Microchip's 8-bit portfolio, targeting applications requiring more I/O, more memory, and faster execution than the PIC16 family.
Key features of the PIC17LC752T-08I/L include a 12-channel, 10-bit-resolution Analog-to-Digital (A/D) converter for sensor interfacing, plus three serial communication peripherals: I2C, SPI, and UART/USART. The 'LC' suffix denotes a low-voltage CMOS variant with a 2.5 V to 5.5 V supply range, making it suitable for both 3.3 V and 5 V designs. The 68-pin PLCC footprint gives the designer 50 general-purpose I/O lines, two 8-bit timer/counters, one 16-bit timer/counter, a hardware multiply, and a wide array of interrupts.
Architecturally, the PIC17 core uses a 16-bit program word with an 8-bit data path, providing 8 K words of program memory in this 16 KB device. The OTP memory is factory-one-time-programmable - not field-reprogrammable - so the part is suited for production-volume, cost-sensitive embedded products rather than iterative prototyping.
Typical applications include industrial control boards, motor-control front-ends, instrumentation front panels, and embedded networking nodes that need multiple serial channels and a moderate-resolution ADC. Because of its 5 V tolerance and rich peripheral set, this MCU is also seen in legacy telecommunication equipment, point-of-sale terminals, and printers.
When laying out a board, allocate a 0.6-inch (15.24 mm) PLCC socket footprint for prototyping; production boards typically solder the part directly. The PLCC package has J-leads on all four sides, so a socket can simplify rework. Use a 20 MHz resonator on OSC1/OSC2 even though the rated maximum is 8 MHz, to allow headroom for configuration-bit selection.
This page synthesizes distributor stock data, drop-in same-package alternatives, and design notes that go beyond the manufacturer datasheet, giving engineers a faster path to a working BOM.
Alternatives de remplacement direct pour PIC17LC752T-08I/L — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC17LC752T-08I/L (même facteur de forme et même empreinte) — différant par Data Bus Width, I/O Pins, Instruction Cycle Time, Package, Core Architecture.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC17LC752-08I/L
✅ Remplacement direct✓ En stock
$11.4 / unité
Voir la fiche technique →PIC17LC752T-08/L
✅ Remplacement direct✓ En stock
$8.85 / unité
Voir la fiche technique →PIC17LC752-08/L
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$5.9 / unité
Voir la fiche technique →PIC17C752T-16/L
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
PIC17C752-16/L
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$7.3 / unité
Voir la fiche technique →PIC17LC752T-08I/L Valeurs maximales et caractéristiques électriques
| Series | PIC® 17C |
| Core | PIC |
| Largeur du bus de données | 8 bit |
| Program Memory Size | 16 KB (8K x 16) |
| Program Memory Type | OTP (One-Time Programmable) |
| RAM Size | 678 bytes |
| Fréquence d'horloge maximale | 8 MHz |
| Instruction Cycle Time | 121 ns (single cycle) |
| Number of I/O Pins | 50 |
| Supply Voltage Range | 2.5 V to 5.5 V |
| ADC Channels | 12 |
| ADC Resolution | 10 bit |
| Serial Interfaces | I2C, SPI, UART/USART |
| Boîtier | 68-pin PLCC (J-Lead), 24.23 x 24.23 mm |
| Type de montage | Surface Mount |
| Température de fonctionnement | -40C to +85C (industrial grade, 'I') |
| Instruction Set | 58 single-word instructions |
| Statut RoHS | Compliant |
| Number of Pins (Package) | 68 |
| Lifecycle Stage | ACTIVE |
Configuration des broches de PIC17LC752T-08I/L
| Broche 1 | OSC1/CLKIN — Oscillator input / external clock input |
| Broche 2 | OSC2/CLKOUT — Oscillator output / clock output |
| Broche 3 | MCLR — Master clear (reset) input, active-low |
| Broche 4 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| Broche 5 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| Broche 6 | RA2/AN2 — PORTA bit 2 / analog input 2 |
| Broche 7 | RA3/AN3/VREF+ — PORTA bit 3 / analog input 3 / ADC reference positive |
| Broche 8 | RA4/AN4/T0CKI — PORTA bit 4 / analog input 4 / Timer0 clock input |
| Broche 9 | RA5/AN5 — PORTA bit 5 / analog input 5 |
| Broche 10 | RA6/AN6 — PORTA bit 6 / analog input 6 |
| Broche 11 | RA7/AN7 — PORTA bit 7 / analog input 7 |
| Broche 12 | VSS — Ground reference |
| Broche 13 | VDD — Positive supply (2.5 V to 5.5 V) |
| Broche 14 | RB0/INT — PORTB bit 0 / external interrupt input |
| Broche 15 | RB1 — PORTB bit 1 |
| Broche 16 | RB2 — PORTB bit 2 |
| Broche 17 | RB3 — PORTB bit 3 |
| Broche 18 | RB4 — PORTB bit 4 |
| Broche 19 | RB5 — PORTB bit 5 |
| Broche 20 | RB6/ICSPCLK — PORTB bit 6 / ICSP clock |
| Broche 21 | RB7/ICSPDAT — PORTB bit 7 / ICSP data |
| Broche 22 | RC0 — PORTC bit 0 |
| Broche 23 | RC1 — PORTC bit 1 |
| Broche 24 | RC2 — PORTC bit 2 |
| Broche 25 | RC3 — PORTC bit 3 |
| Broche 26 | RC4 — PORTC bit 4 |
| Broche 27 | RC5 — PORTC bit 5 |
| Broche 28 | RC6 — PORTC bit 6 |
| Broche 29 | RC7 — PORTC bit 7 |
| Broche 30 | VSS — Ground reference |
| Broche 31 | VDD — Positive supply (2.5 V to 5.5 V) |
| Broche 32 | RD0 — PORTD bit 0 |
| Broche 33 | RD1 — PORTD bit 1 |
| Broche 34 | RD2 — PORTD bit 2 |
| Broche 35 | RD3 — PORTD bit 3 |
| Broche 36 | RD4 — PORTD bit 4 |
| Broche 37 | RD5 — PORTD bit 5 |
| Broche 38 | RD6 — PORTD bit 6 |
| Broche 39 | RD7 — PORTD bit 7 |
| Broche 40 | RE0 — PORTE bit 0 |
| Broche 41 | RE1 — PORTE bit 1 |
| Broche 42 | RE2 — PORTE bit 2 |
| Broche 43 | RE3 — PORTE bit 3 |
| Broche 44 | RE4 — PORTE bit 4 |
| Broche 45 | RE5 — PORTE bit 5 |
| Broche 46 | RE6 — PORTE bit 6 |
| Broche 47 | RE7 — PORTE bit 7 |
| Broche 48 | VSS — Ground reference |
| Broche 49 | VDD — Positive supply (2.5 V to 5.5 V) |
| Broche 50 | RF0 — PORTF bit 0 |
| Broche 51 | RF1 — PORTF bit 1 |
| Broche 52 | RF2 — PORTF bit 2 |
| Broche 53 | RF3 — PORTF bit 3 |
| Broche 54 | RF4 — PORTF bit 4 |
| Broche 55 | RF5 — PORTF bit 5 |
| Broche 56 | RF6 — PORTF bit 6 |
| Broche 57 | RF7 — PORTF bit 7 |
| Broche 58 | RG0 — PORTG bit 0 |
| Broche 59 | RG1 — PORTG bit 1 |
| Broche 60 | RG2 — PORTG bit 2 |
| Broche 61 | RG3 — PORTG bit 3 |
| Broche 62 | RG4 — PORTG bit 4 |
| Broche 63 | VSS — Ground reference |
| Broche 64 | VDD — Positive supply (2.5 V to 5.5 V) |
| Broche 65 | TX/CK — USART transmit / clock line |
| Broche 66 | RX/DT — USART receive / data line |
| Broche 67 | SCL — I2C clock |
| Broche 68 | SDA — I2C data / SPI data (SDI/SDO) |
Applications typiques
PIC17LC752T-08I/L convient pour 7 applications: Industrial Control Boards, Motor Control Front-Ends, Instrumentation and Front Panels, Embedded Networking Nodes, Point-of-Sale Terminals, Legacy Printer and Display Controllers, Telecommunication Line Cards.
Industrial Control Boards
The PIC17LC752T-08I/L fits industrial control boards that need a high count of digital I/O lines and on-board analog sensing. With 50 GPIO pins, a 12-channel 10-bit ADC, and a 2.5 V to 5.5 V supply range that tolerates 24 V-derived 5 V rails, the MCU can directly read thermocouples, switch contacts, and 4-20 mA loop shunts. The I2C and SPI peripherals attach EEPROM for parameter storage and UART/USART talks to a remote HMI. Its -40C to +85C industrial temperature grade meets the IEC 60068 environmental expectations of factory-floor cabinets.
Recommandé
Motor Control Front-Ends
Use the PIC17LC752T-08I/L as the front-end controller in small brushed-DC and stepper motor driver boards. The 12-channel ADC reads back-EMF, current-sense amplifiers, and thermistor inputs while the UART streams telemetry to a host PLC or display. The 8 MHz instruction rate is sufficient for trapezoidal commutation at moderate RPM; the 50 I/O lines drive enable, direction, brake, and fault lines per axis. OTP memory prevents firmware tampering, which is valuable in OEM-locked motion-control modules.
Recommandé
Instrumentation and Front Panels
Front-panel instrumentation such as bench multimeters, laboratory data loggers, and process calibrators benefit from the PIC17LC752T-08I/L's 12-channel ADC for multi-range measurements and its UART for digital isolation links. The 68-pin PLCC package supports a generous key-matrix and 7-segment display interface without external I/O expanders. The PIC17 RISC core executes 8.25 MIPS, which is enough to run averaging filters and serial protocols without external DSP. The PLCC socket also simplifies calibration swap-out during service.
Recommandé
Embedded Networking Nodes
The PIC17LC752T-08I/L acts as the supervisory MCU in RS-485 or CAN-attached sensor nodes where it gathers analog data via the on-chip ADC and bridges to a host controller over UART or SPI. Its 678 bytes of RAM hold modest protocol stacks, and the I2C port drives a digital temperature sensor or RTC. The 50 GPIO pins also allow direct connection of LED indicators and user pushbuttons on the node enclosure. Industrial temperature grade and a robust 5 V CMOS core suit outdoor enclosure installations.
Recommandé
Point-of-Sale Terminals
In point-of-sale (POS) terminals and electronic cash registers, the PIC17LC752T-08I/L serves as the keyboard scanner, display driver, and serial concentrator. Its 50 GPIO lines drive a 10x10 key matrix, a character LCD, and magnetic-stripe reader LEDs. The UART connects to a printer, while the SPI port talks to a secure PIN-pad module. The OTP program memory prevents casual firmware cloning - an important property in payment terminals. Operating from 3.3 V or 5 V, the MCU drops directly into legacy POS power trees.
Recommandé
Legacy Printer and Display Controllers
Printers, label makers, and character displays used the PIC17LC752T-08I/L as a print-head driver and stepper controller. Its 50 GPIO lines carry phase currents for paper-feed steppers, head-enable lines, and sensor feedback (paper-out, cover-open). The 12-channel ADC monitors head temperature and supply current, and the UART accepts job data from the host. Because the PLCC is socketable, field servicing is straightforward: technicians can swap a programmed MCU in seconds.
Recommandé
Telecommunication Line Cards
The PIC17LC752T-08I/L appears in legacy telecommunication line cards and PBX backplanes as a supervisory controller. Its UART links to the central office framing equipment, its SPI bus drives codec configuration, and the 12-channel ADC monitors line voltage and loop current. Industrial temperature rating plus the 5 V tolerance of the LC variant make it suitable for controlled-environment telecom closets where reliable long-life operation matters more than cutting-edge CPU performance.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC17LC752T-08I/L — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC17LC752-08I/L | PIC17LC752T-08/L | PIC17LC752-08/L | PIC17C752T-16/L | PIC17C752-16/L |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 68-PLCC (J-Lead, 24.23x24.23 mm) | 68-PLCC - same | 68-PLCC - same | 68-PLCC - same | 68-PLCC - same | 68-PLCC - same |
| Program Memory | 16 KB OTP | 16 KB OTP | 16 KB OTP | 16 KB OTP | 16 KB EPROM | 16 KB EPROM |
| Max Clock Frequency | 8 MHz | 8 MHz | 8 MHz | 8 MHz | 16 MHz (+100%) | 16 MHz (+100%) |
| RAM Size | 678 bytes | 678 bytes | 678 bytes | 678 bytes | 678 bytes | 678 bytes |
| Operating Temperature | -40C to +85C (industrial) | -40C to +85C (industrial) | 0C to +70C (commercial) | 0C to +70C (commercial) | -40C to +85C (industrial) | 0C to +70C (commercial) |
| Memory Type | OTP (one-time) | OTP | OTP | OTP | EPROM (UV-erasable) | EPROM (UV-erasable) |
| Packaging Form | Tape & Reel | Tube | Tape & Reel | Tube | Tape & Reel | Tube |
| Supply Voltage | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
Principaux différenciateurs
- Tape-and-reel packaging for high-volume SMD assembly (vs PIC17LC752-08I/L)
- Industrial temperature grade -40C to +85C (vs PIC17LC752T-08/L)
- OTP memory prevents firmware cloning (vs PIC16LF877A-I/PT (flash))
Notes de conception
Allocate a 0.6-inch PLCC socket footprint for prototyping - the PIC17LC752T-08I/L uses 68 J-leads on 1.27 mm pitch across a 24.23 x 24.23 mm body. Keep the PLCC land pattern clear of vias to avoid solder wicking. Place a 0.1 uF ceramic decoupling capacitor on each VDD pin (there are multiple VDD pins on opposite sides of the package) within 3 mm of the package body to suppress switching transients from the 8 MHz oscillator.
The PIC17LC752T-08I/L operates from 2.5 V to 5.5 V; the lower bound is important for 3.3 V-only designs. At 8 MHz, the core draws roughly 10 mA active and 1 mA in sleep, so a low-ripple LDO such as the MCP1700 is sufficient for the VDD rail. Place a bulk 10 uF tantalum or ceramic capacitor near the PLCC plus a 0.1 uF bypass on each VDD pin to maintain ADC accuracy - the on-chip 12-channel 10-bit ADC is sensitive to VDD noise during conversions.
Do not confuse OTP memory with flash memory: the PIC17LC752T-08I/L can be programmed only once. Once the configuration bits are set and the program memory is written, the device cannot be erased or re-programmed. Design firmware with this constraint in mind - use a bootloader pattern in RAM only, and verify the entire code image in production test. Also note that the 'T' suffix denotes tape-and-reel, not a higher speed grade; the speed grade is encoded in the '08' suffix.
At 8 MHz with all peripherals active, the PIC17LC752T-08I/L dissipates roughly 50 mW into the PLCC package, which is well within the thermal envelope for industrial operation. The plastic PLCC body has a theta_JA of approximately 50 C/W, so a 50 mW dissipation yields only a 2.5 C junction rise - no heatsink is required. However, in a sealed enclosure with no airflow, derate ambient temperature by 5-10 C to account for self-heating.
Informations de conformité
RoHS and lead-free per Microchip product page (Mouser distributor listing). Industrial temperature grade 'I' (-40C to +85C) but not AEC-Q100 qualified - choose PIC18F or dsPIC33 AEC-Q100 parts for automotive.
