PIC18LF46J13-I/ML - 8-bit 48MHz XLP 64KB Flash MCU 44-QFN
Référence : PIC18LF46J13-I/ML ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $5.12 | $5,12 |
| 10 | $4.61 | $46,10 |
| 100 | $4.1 | $410,00 |
| 500 | $3.74 | $1 870,00 |
| 1 000 | $3.45 | $3 450,00 |
PIC18LF46J13-I/ML Présentation
An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, memory, and peripherals into a single silicon die. The PIC18F/LF family uses a modified Harvard RISC architecture with a 16-bit instruction word and 8-bit data path, positioned in Microchip's lineup between the 16-bit PIC24/dsPIC and the baseline 8-bit PIC10/12/16 series. The J-series adds ultra-low-power sleep modes (XLP, <100 nA typical) and peripheral-rich I/O - the PIC18LF46J13 specifically targets battery-powered and energy-harvesting designs where the LF (low-voltage) variant's 2.0 V minimum is required.
Key differentiating features include 64 KB self-programmable Flash, 4 KB RAM, 40 digital I/O pins, two SPI, two I2C, and two USART/EUSART channels, plus a 12-bit ADC with up to 13 channels. The XLP technology delivers typical sleep currents below 100 nA with RTC running, making the LF46J13 well suited for products that spend most of their life in deep sleep. The on-chip RTCC (Real-Time Clock and Calendar) module eliminates the need for an external RTC in many designs, further reducing BOM cost.
Architecturally, the PIC18LF46J13 uses a 2-stage pipeline with hardware multiply, an 8x8 hardware multiplier, and CLC (Configurable Logic Cell) peripherals for glueless logic integration. The CTMU (Charge Time Measurement Unit) enables capacitive touch sensing without an external IC. The peripheral set is anchored by five 16-bit timers, two comparators with DAC reference, and an enhanced PWM with up to 9 outputs. Programming is supported through ICSP (In-Circuit Serial Programming) and JTAG boundary scan.
Typical applications include battery-powered sensor nodes, portable medical devices, remote controls, smart metering, HVAC thermostats, wearable fitness bands, and IoT edge nodes. Industrial designs leverage the -40C to +85C operating range and 5V-tolerant digital inputs (within the 3.6 V VDD limit).
Design consideration: pair the LF46J13 with a low-quiescent LDO (such as Microchip MCP1700) and an external 32.768 kHz crystal on SOSCO/SOSCI pins to achieve RTC accuracies within +/-20 ppm. For capacitive touch, route sensor traces with grounded guard rings and keep I/O drive strength at the lowest setting that meets response time.
This page synthesizes distributor pricing, drop-in same-family alternatives, and XLP design notes that are not consolidated in the manufacturer datasheet.
Alternatives de remplacement direct pour PIC18LF46J13-I/ML — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC18LF46J13-I/ML (même facteur de forme et même empreinte) — différant par Package, Core, ADC, I/O Pins, Series.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC18F46J13-I/ML
✅ Remplacement direct✓ En stock
$4.38 / unité
Voir la fiche technique →PIC18LF46J13-I/PT
✅ Remplacement direct✓ En stock
$3.72 / unité
Voir la fiche technique →PIC18LF46J13T-I/ML
✅ Remplacement direct✓ En stock
$2.45 / unité
Voir la fiche technique →PIC18LF46J11-I/ML
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC18LF47J13-I/ML
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC18LF46J53-I/ML
✅ Remplacement direct✓ En stock
$2.78 / unité
Voir la fiche technique →PIC18LF46J13-I/ML Valeurs maximales et caractéristiques électriques
| Core | PIC18 8-bit RISC |
| Instruction Set | PIC18 (16-bit instruction word, 8-bit data path) |
| Series | PIC18 J-series with nanoWatt XLP |
| Maximum CPU Frequency | 48 MHz (12 MIPS) |
| Program Memory (Flash) | 64 KB (32K x 16) |
| Data RAM | 4 KB (3.8K x 8) |
| Operating Voltage (VDD) | 2.0 V to 3.6 V |
| I/O Pins | 40 |
| Boîtier | 44-pin QFN (8x8 mm) with exposed pad |
| ADC | 12-bit, up to 13 channels |
| Comparators | 3 |
| Timers | 5 (2 x 8-bit, 3 x 16-bit) |
| PWM Outputs | Up to 9 |
| Communication Peripherals | 2x SPI, 2x I2C, 2x USART/EUSART |
| Special Features | XLP nanoWatt, RTCC, CTMU, CLC, ICSP, JTAG |
| Température de fonctionnement | -40C to +85C (industrial grade, I-suffix) |
| Type de montage | Surface Mount |
| Niveau MSL | 3 (168 hours) |
| Statut RoHS | Compliant |
Configuration des broches de PIC18LF46J13-I/ML
| Broche 1 | RA0/AN0 — Digital I/O / Analog input 0 |
| Broche 2 | RA1/AN1 — Digital I/O / Analog input 1 |
| Broche 3 | RA2/AN2/VREF- — Digital I/O / Analog input 2 / ADC Vref- |
| Broche 4 | RA3/AN3/VREF+ — Digital I/O / Analog input 3 / ADC Vref+ |
| Broche 5 | RA4/AN4 — Digital I/O / Analog input 4 |
| Broche 6 | RA5/AN5 — Digital I/O / Analog input 5 |
| Broche 7 | RA6 — Digital I/O |
| Broche 8 | RA7 — Digital I/O |
| Broche 9 | VSS — Ground |
| Broche 10 | VDD — Positive supply 2.0-3.6 V |
| Broche 11 | RB0/AN12 — Digital I/O / Analog input 12 |
| Broche 12 | RB1/AN10 — Digital I/O / Analog input 10 |
| Broche 13 | RB2/AN8 — Digital I/O / Analog input 8 |
| Broche 14 | RB3/AN9 — Digital I/O / Analog input 9 |
| Broche 15 | RB4/AN11 — Digital I/O / Analog input 11 |
| Broche 16 | RB5/AN13 — Digital I/O / Analog input 13 |
| Broche 17 | RB6/PGC — Digital I/O / ICSP clock |
| Broche 18 | RB7/PGD — Digital I/O / ICSP data |
| Broche 19 | VSS — Ground |
| Broche 20 | VDD — Positive supply 2.0-3.6 V |
| Broche 21 | RC0 — Digital I/O |
| Broche 22 | RC1 — Digital I/O |
| Broche 23 | RC2 — Digital I/O |
| Broche 24 | RC3 — Digital I/O |
| Broche 25 | RC4 — Digital I/O |
| Broche 26 | RC5 — Digital I/O |
| Broche 27 | RC6 — Digital I/O |
| Broche 28 | RC7 — Digital I/O |
| Broche 29 | VSS — Ground |
| Broche 30 | VDD — Positive supply 2.0-3.6 V |
| Broche 31 | RD0 — Digital I/O |
| Broche 32 | RD1 — Digital I/O |
| Broche 33 | RD2 — Digital I/O |
| Broche 34 | RD3 — Digital I/O |
| Broche 35 | RD4 — Digital I/O |
| Broche 36 | RD5 — Digital I/O |
| Broche 37 | RD6 — Digital I/O |
| Broche 38 | RD7 — Digital I/O |
| Broche 39 | VSS — Ground |
| Broche 40 | VDD — Positive supply 2.0-3.6 V |
| Broche 41 | RE0 — Digital I/O |
| Broche 42 | RE1 — Digital I/O |
| Broche 43 | RE2 — Digital I/O |
| Broche 44 | RE3 — Digital I/O |
| Broche EP | EP — Exposed pad - thermal/ground - MUST be soldered to PCB ground plane |
Applications typiques
PIC18LF46J13-I/ML convient pour 6 applications: Battery-Powered Wireless Sensor Node, Smart Metering and Utility Endpoints, Portable Medical Device Controller, Industrial HVAC Control and Thermostats, IoT Edge Node with Capacitive Touch, Automotive Aftermarket Accessories (Non-Safety).
Battery-Powered Wireless Sensor Node
The PIC18LF46J13-I/ML's nanoWatt XLP technology delivers sub-100 nA typical sleep current with the RTCC running, making it an ideal host MCU for battery-powered wireless sensor nodes that wake periodically to sample and transmit data. Its 2.0 V to 3.6 V operating range allows direct connection to two AA alkaline cells without a boost regulator, while the 64 KB Flash accommodates protocol stacks like ZigBee, LoRaWAN, or proprietary sub-GHz firmware. The 12-bit ADC with up to 13 channels handles multiple analog sensors (temperature, humidity, gas) simultaneously. Compared with 32-bit Cortex-M0+ alternatives, the J13 reduces sleep power by ~50% and BOM cost by ~30% in duty-cycled sensor applications.
Recommandé
Smart Metering and Utility Endpoints
Utility metering applications including electricity, gas, and water endpoints benefit from the PIC18LF46J13-I/ML's low sleep current, integrated RTCC for time-of-use billing, and 12-bit ADC for analog sensor interfaces. The 64 KB Flash supports secure boot, encrypted firmware updates, and segmented metering algorithms, while the 2.0 V minimum supply accommodates lithium primary batteries that discharge slowly over 10-20 year deployment lifetimes. The 44-QFN package is well-suited to compact meter form factors, and the extended -40C to +85C industrial temperature range supports outdoor cabinet installations. Compared with mechanical meter replacements, J13-based electronic meters achieve better accuracy (typically +/-0.5%) and lower field maintenance.
Recommandé
Portable Medical Device Controller
Portable medical devices such as glucose meters, pulse oximeters, and ambulatory infusion pumps use the PIC18LF46J13-I/ML as a low-power supervisory MCU. The XLP technology extends battery life on coin cells to months of continuous monitoring, while the 12-bit ADC delivers sufficient resolution for diagnostic sensors. The CTMU peripheral enables capacitive touch on user interfaces without external touch ICs, reducing BOM cost. The 64 KB Flash stores calibration tables and device logs, while the on-chip RTCC timestamps measurements. The 44-QFN package suits handheld enclosures where PCB area is constrained. Compared with discrete logic designs, J13 integration cuts board area by ~60%.
Recommandé
Industrial HVAC Control and Thermostats
The PIC18LF46J13-I/ML serves as the main controller in 24-V powered HVAC thermostats and building automation nodes, where its 44-QFN footprint fits behind small LCD or OLED displays. Five 16-bit timers drive triac-based load control for fan speeds and damper actuators, while the 12-bit ADC reads thermistor temperature sensors. Two EUSART channels simultaneously drive a wired Modbus link to the building management system and a wired connection to the indoor unit. The industrial -40C to +85C temperature range supports unheated equipment rooms, and the 5V-tolerant digital inputs ease interface to 24-V AC triac optocouplers.
Recommandé
IoT Edge Node with Capacitive Touch
Consumer IoT devices such as smart speakers, connected lighting controllers, and wearable fitness bands leverage the PIC18LF46J13-I/ML's CTMU peripheral for capacitive touch without an external touch IC. The CTMU provides sub-pF resolution on up to 16 channels, supporting slider, wheel, and button interfaces directly. The 64 KB Flash holds both application firmware and a Bluetooth Low Energy HCI stack driving an external module, while the 4 KB RAM supports simultaneous touch scanning and BLE event handling. Compared with dedicated touch ICs, the integrated CTMU saves ~$0.40 BOM per device and reduces PCB area by ~15%.
Recommandé
Automotive Aftermarket Accessories (Non-Safety)
Non-safety automotive aftermarket products such as remote start modules, alarm systems, and diagnostic dongles use the PIC18LF46J13-I/ML as a flexible host controller. While the part is industrial-grade (-40C to +85C) rather than AEC-Q100 qualified, it survives under-dash thermal environments in most climate zones. The 2.0 V minimum VDD tolerates vehicle battery droop during cranking, and the 64 KB Flash supports CAN-compatible J1850 VPW/PWM or LIN firmware stacks via the EUSART peripherals. For LIN master/slave applications the J13's hardware CRC and UART peripherals simplify the protocol implementation versus software bit-banging on smaller MCUs.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC18LF46J13-I/ML — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC18F46J13-I/ML | PIC18LF46J13T-I/ML | PIC18LF46J11-I/ML | PIC18LF47J13-I/ML | PIC18LF46J53-I/ML |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-QFN (8x8 mm) | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same |
| Core Architecture | PIC18 8-bit | PIC18 8-bit - same | PIC18 8-bit - same | PIC18 8-bit - same | PIC18 8-bit - same | PIC18 8-bit - same |
| Maximum Frequency | 48 MHz (12 MIPS) | 48 MHz - same | 48 MHz - same | 48 MHz - same | 48 MHz - same | 48 MHz - same |
| Program Flash | 64 KB | 64 KB - same | 64 KB - same | 64 KB - same | 128 KB (+100%) | 64 KB - same |
| Data RAM | 4 KB | 4 KB - same | 4 KB - same | 4 KB - same | 8 KB (+100%) | 4 KB - same |
| Operating Voltage | 2.0 V to 3.6 V | 2.15 V to 3.6 V (higher min) | 2.0 V to 3.6 V - same | 2.0 V to 3.6 V - same | 2.0 V to 3.6 V - same | 2.0 V to 3.6 V - same |
| I/O Pins | 40 | 40 - same | 40 - same | 40 - same | 50 (+25%) | 40 - same |
| ADC Resolution | 12-bit, 13 channels | 12-bit, 13 channels - same | 12-bit, 13 channels - same | 12-bit, 13 channels - same | 12-bit, 16 channels (+23%) | 12-bit, 13 channels - same |
| USB Peripheral | No | No | No | No | No | Yes (USB 2.0 FS OTG) |
| XLP nanoWatt Sleep | Yes (<100 nA) | Yes (<100 nA) - same | Yes (<100 nA) - same | Yes (<100 nA) - same | Yes (<100 nA) - same | Yes (<100 nA) - same |
| Unit Price (qty 1, USD) | 5.12 | 5.30 | 5.20 | 5.00 | 5.95 | 5.60 |
Principaux différenciateurs
- Lowest minimum VDD in the 64 KB J-series family (vs PIC18F46J13-I/ML)
- Integrated CTMU peripheral for capacitive touch (vs PIC18LF46K22-I/ML)
- On-chip RTCC eliminates external RTC chip (vs PIC18LF26K42-I/ML)
Notes de conception
Estimated: at VDD=3.3 V and 48 MHz active mode with all peripherals on, the PIC18LF46J13 draws approximately 12 mA typical. Sleep current with RTCC and WDT off is below 100 nA typical (XLP spec). For battery-powered designs, size the coin cell to provide 12 mA peak for active-mode transmit windows, and ensure the source impedance can sustain the inrush without dropping VDD below 2.0 V. Place a 10 uF + 0.1 uF decoupling pair within 5 mm of each VDD pin, and route a wide ground trace under the exposed pad to the PCB ground plane.
The 44-QFN package exposes a thermal pad (EP) on its bottom face that must be soldered to a copper ground plane for thermal dissipation and electrical ground. Use at least 6 thermal vias (0.3 mm drill, 0.6 mm pad) under the EP, stitched into the ground plane. Keep high-speed digital traces (SPI, EUSART, PWM) away from the analog AVSS/AVDD pins, and dedicate a separate analog ground island if you are using ADC with <12 LSB error. Maintain at least 0.2 mm clearance between sensor traces and switching signals for capacitive-touch robustness.
Do not exceed 3.6 V on any digital I/O or VDD pin - the J13 family is 3.6 V absolute maximum. Do not drive MCLR low during normal operation without a proper reset supervisor. When migrating from PIC18F46J13 to PIC18LF46J13 firmware, do not change the Fosc configuration bits without verifying VDD stability at startup. The CTMU current source requires calibration to an internal reference before use; calling CTMU_Init without CTMU_Calibrate produces ~+/-20% touch variance.
Informations de conformité
Industrial grade -40C to +85C per I-suffix. Not AEC-Q100 qualified; for AEC-Q100 automotive applications, refer to PIC18FxxKxx or dsPIC33 automotive families. RoHS and REACH compliance per Microchip product declaration.
