PIC24FV16KM204-E/PT - 16-Bit 32MHz Low-Power MCU | Microchip
Référence : PIC24FV16KM204-E/PT ✓ ActifPIC24FV16KM204-E/PT Présentation
A low-power microcontroller is a specialized semiconductor that combines a processor core, memory, analog peripherals, and communication interfaces into one compact device. The PIC24 architecture belongs to the broader microcontroller and embedded-controller hierarchy, while the XLP designation identifies Microchip's low-power design approach. These devices are used where accurate analog measurement, programmable output, and low standby consumption must coexist in a small embedded package.
The PIC24FV16KM204-E/PT provides 16 KB of Flash program memory and 2 KB of SRAM for firmware and working data. Its 12-bit ADC supports analog sensing, while the 8-bit DAC provides a programmable analog output without requiring a separate converter. Integrated operational amplifiers can reduce the component count in front-end circuits. A maximum operating frequency of 32 MHz supports responsive control loops and mixed peripheral operation.
The device uses the enhanced 16-bit PIC24 instruction set and includes programmable timers, communication peripherals, interrupt handling, and configurable digital I/O. Its 36 interrupt sources and four trap mechanisms support responsive event-driven firmware. The 37 available I/O pins give the 44-pin device substantial connectivity without requiring a larger package, although the exact peripheral mapping must be assigned from the manufacturer pin-description table.
Typical uses include industrial sensor acquisition, environmental monitoring, consumer controls, compact power conversion, and low-power instrumentation. The integrated ADC, DAC, and op amps are especially useful in systems that measure a physical variable and generate an analog output. The operating range of 1.8 V to 5.5 V also permits deployment in low-voltage embedded systems and portable products.
When designing the PCB, reserve decoupling capacitors at each supply pin and route analog signals away from fast-switching digital nets. Verify the selected peripheral pins against the 44-pin TQFP footprint before finalizing the schematic. For battery-powered equipment, use the controller's low-power modes and disable unused peripherals because firmware-controlled clock and peripheral states determine much of the system-level consumption.
This page combines the manufacturer's device specifications, package details, functional comparisons, and practical design guidance to support component selection and PCB implementation. It also distinguishes confirmed drop-in alternatives from variants that require additional pin and qualification checks.
Alternatives de remplacement direct pour PIC24FV16KM204-E/PT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC24FV16KM204-E/PT (même facteur de forme et même empreinte) — différant par Package, ADC, Maximum CPU Speed, Comparators, DAC.
PIC24F16KM204-E/PT
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →PIC24FV16KM204-I/PT
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →PIC24F16KM204-I/PT
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →PIC24FV16KM204-E/PT Valeurs maximales et caractéristiques électriques
| Architecture | 16-bit PIC24 MCU |
| Maximum CPU Frequency | 32 MHz |
| Program Memory | 16 KB Flash |
| Program Memory Organization | 5.5K x 24 words |
| RAM | 2 KB |
| EEPROM | 512 B |
| ADC Resolution | 12-bit |
| DAC Resolution | 8-bit |
| Integrated Operational Amplifiers | 2 integrated operational amplifiers |
| Operating Voltage Range | 1.8 V to 5.5 V |
| I/O Pin Count | 37 pins |
| Interrupt Sources | 36 sources |
| Trap Count | 4 traps |
| Boîtier | 44-pin TQFP, 10 mm x 10 mm |
| Type de montage | Surface mount |
| Programmable Timing and PWM Peripherals | Capture, Compare, and PWM modules |
Guide de configuration des broches du PIC24FV16KM204-E/PT 44-pin tqfp, 10 mm x 10 mm
Configuration des broches du PIC24FV16KM204-E/PT (boîtier 44-pin tqfp, 10 mm x 10 mm). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour PIC24FV16KM204-E/PT.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
PIC24FV16KM204-E/PT convient pour 6 applications: Industrial Sensor Acquisition, Environmental Monitoring, Consumer Control Interface, Compact Data Acquisition Module, Low-Voltage Power Control, Connected Sensor Node.
Industrial Sensor Acquisition
PIC24FV16KM204-E/PT fits industrial sensor nodes that need a compact controller with local analog measurement. Its 12-bit ADC provides 4096 discrete conversion levels, while the 32 MHz CPU supports acquisition scheduling, filtering, and communication handling. The 37 I/O pins leave room for sensors, status indicators, and digital interfaces without moving to a larger enclosure. Operate the controller from its 1.8 V to 5.5 V range and place input filtering close to the source. The integrated ADC reduces component count, but application-specific calibration, channel selection, and analog grounding remain necessary to obtain repeatable measurements.
Recommandé
Environmental Monitoring
The PIC24FV16KM204-E/PT can act as the central controller in a battery-assisted environmental monitor that samples temperature, humidity, or gas sensors. Its 12-bit ADC supports sensor conditioning, while the 8-bit DAC can produce a low-level reference or test signal when required. The 16 KB Flash and 2 KB RAM are sufficient for a focused acquisition and logging design, subject to the final firmware footprint. Low-power operation from 1.8 V to 5.5 V supports portable systems. Select the XLP sleep mode carefully, disable unused converters, and account for sensor-heater energy rather than microcontroller current alone when estimating battery life.
Recommandé
Consumer Control Interface
PIC24FV16KM204-E/PT is suitable for compact consumer controls that combine touch or switch inputs, status lighting, and a local analog function. Its 37 I/O pins provide ample connections for buttons, indicators, and serial peripherals in a 44-pin TQFP footprint. The 32 MHz 16-bit processor can service timers, interrupts, and display or communication updates while leaving headroom for application logic. The integrated op amps may support low-level signal conditioning and the 8-bit DAC may generate an auxiliary analog output. Because the I/O count does not imply that every peripheral function is simultaneously available, verify pin multiplexing and active-state requirements against the manufacturer pin table.
Recommandé
Compact Data Acquisition Module
The PIC24FV16KM204-E/PT can serve as the acquisition engine in a compact industrial or instrumentation module. Its 12-bit ADC performs the primary analog conversion, the 32 MHz CPU executes sampling and scaling routines, and 2 KB of RAM supports temporary buffering. With 16 KB of Flash, designers can combine acquisition control, calibration, and a communication protocol in one device. The 44-pin TQFP package keeps the assembly compact but requires careful escape routing between fine-pitch pins. Follow the manufacturer pin-description table for ADC inputs, supply pins, and ground connections, and use separate analog and digital return paths to prevent switching activity from corrupting measurements.
Recommandé
Low-Voltage Power Control
PIC24FV16KM204-E/PT can supervise a low-voltage power system that operates between 1.8 V and 5.5 V. Its 12-bit ADC can monitor a divided feedback voltage, current signal, or temperature, while the 8-bit DAC provides a programmable control or bias output. The 32 MHz processing speed allows timely execution of control loops and fault handling. The two integrated operational amplifiers may assist with error amplification or signal conditioning, subject to their documented input and output limitations. For power-conversion designs, verify the control-loop compensation and converter switching rates against the MCU peripherals before committing to a topology; the microcontroller does not eliminate the need for power-stage design.
Recommandé
Connected Sensor Node
PIC24FV16KM204-E/PT is well suited to a compact connected sensor node that combines measurement, local processing, and serial communication. The controller provides 16 KB of Flash, 2 KB of RAM, 37 I/O pins, and 36 interrupt sources for event-driven sensor and communication handling. Its 12-bit ADC supports analog sensing, and the low 1.8 V operating limit permits use with energy-harvesting front ends or single-cell power systems. The XLP architecture helps when the node spends most of its time idle, although radio and sensor power can dominate consumption. Select pins with attention to peripheral multiplexing, and validate communication timing under sleep, wake, and peripheral-clock transitions.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC24FV16KM204-E/PT — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC24F16KM204-E/PT | PIC24FV16KM204-I/PT | PIC24F16KM204-I/PT |
|---|---|---|---|---|
| Package | 44-pin TQFP (10 mm x 10 mm) | 44-pin TQFP (10 mm x 10 mm) | 44-pin TQFP (10 mm x 10 mm) | 44-pin TQFP (10 mm x 10 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Architecture | 16-bit PIC24 MCU | 16-bit PIC24 MCU | 16-bit PIC24 MCU | 16-bit PIC24 MCU |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 16 KB | 16 KB | 16 KB | 16 KB |
| Ordering Code | E/PT grade and tray package | E/PT grade and tray package | I/PT grade and tray package | I/PT grade and tray package |
Principaux différenciateurs
- Combines three analog resources in one low-power controller (vs PIC24F16KM204-E/PT)
- Maintains the full 16-bit performance profile (vs PIC24FV16KM204-I/PT)
- Preserves a 37-I/O-pin design footprint (vs PIC24F16KM204-I/PT)
Notes de conception
Assign every function from the manufacturer pin-description table before routing the 44-pin TQFP footprint. The controller provides 37 I/O pins, but analog inputs, DAC outputs, op-amp connections, programming signals, and digital functions can be multiplexed. Confirm that every simultaneously required peripheral has a non-conflicting pin assignment. Use the package drawing for land-pattern geometry and preserve clearance between adjacent fine-pitch tracks.
Place the required bypass capacitors close to the device supply pins and route them using short, low-loop-inductance paths. The supported operating range is 1.8 V to 5.5 V, so the complete system must remain within that range during startup, shutdown, and load transients. For a battery design, calculate the average current from the MCU, ADC, DAC, op amps, sensors, and communications separately; entering sleep does not reduce the load of other enabled subsystems.
Keep analog inputs and the 12-bit ADC circuitry away from high-current switching nodes and fast digital edges. Provide a direct ground path for analog return currents and connect it to the device ground pins according to the manufacturer layout guidance. If the op amps or DAC participate in signal generation, evaluate output loading, settling behavior, and noise coupling at the intended signal bandwidth rather than relying only on nominal converter resolution.
Do not select a replacement from package appearance alone. PIC24F16KM204-E/PT, PIC24FV16KM204-I/PT, and PIC24F16KM204-I/PT use the same 44-pin format, but family, ordering-grade, peripheral multiplexing, and qualification requirements still matter. After substitution, rebuild the project, compare configuration words and register definitions, exercise ADC, DAC, timers, interrupts, and communications, and verify the complete temperature range before production use.
Informations de conformité
The exact compliance declarations for this ordering code are not stated on the manufacturer product page. Check the current manufacturer material-declaration documentation for RoHS, REACH, halogen content, and conflict-minerals requirements before procurement.