PIC32MX550F256LT-V/PF - 32-bit 256KB Flash MCU | Microchip 100-TQFP
Référence : PIC32MX550F256LT-V/PF ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $7.1 | $7,10 |
| 10 | $6.42 | $64,20 |
| 100 | $5.71 | $571,00 |
| 500 | $5.12 | $2 560,00 |
| 1 000 | $4.55 | $4 550,00 |
PIC32MX550F256LT-V/PF Présentation
A 32-bit microcontroller (MCU) is an embedded computing device that integrates a CPU core, program and data memory, and a rich set of on-chip peripherals into a single silicon die. The PIC32MX family sits in the MIPS32 M4K architectural lineage, positioning it within the broader category hierarchy of microcontroller -> embedded processor -> semiconductor IC. Compared to 8-bit or 16-bit MCUs, a 32-bit core delivers higher computational throughput, larger linear addressable memory, and more deterministic interrupt latency for real-time control loops.
Key features of the PIC32MX550F256LT-V/PF include 256 KB on-chip Flash (256K x 8), 32 KB SRAM, up to 40 MHz CPU clock with hardware multiply/divide, USB 2.0 full-speed device/host/OTG, a CAN 2.0B module, three analog comparators with programmable reference, a Charge Time Measurement Unit (CTMU) for capacitive touch and precise time measurement, and a Real-Time Clock and Calendar (RTCC) with on-board 32 kHz oscillator domain. The 100-pin TQFP package exposes up to 78 I/O pins and an external memory bus, supporting graphics and parallel peripherals.
Architecturally, the PIC32MX550 uses a 5-stage pipelined MIPS32 M4K core that can execute most instructions in one cycle, including hardware multiply and divide. The device operates from 2.3V to 3.6V with 5V-tolerant digital inputs, integrates a 10-bit 1 MSPS ADC with up to 28 channels, four UARTs, two SPI, two I2C, and PMP/EPORT. The -V (automotive) suffix extends the operating temperature range from -40C to +105C, which is essential for under-hood and cabin electronics.
Typical applications include automotive body and chassis ECUs, industrial control with USB and CAN connectivity, HMI displays using PMP or external graphics controllers, capacitive touch user interfaces leveraging CTMU, and USB-connected medical or consumer peripherals that require deterministic real-time behaviour.
Designers should plan for 3.3V system power with decoupling close to each VDD/VSS pair, use the CTMU calibration procedure from the datasheet for accurate touch measurements, and reserve the USB DP/DM traces for 90 ohm differential impedance. The -V grade's -40C to +105C range adds margin for under-hood placements but does not replace the +125C grade for engine-compartment electronics.
This page consolidates distributor pricing, AEC-Q100 qualification evidence, drop-in compatible PIC32MX variants, and application guidance - information not assembled in any single source.
Alternatives de remplacement direct pour PIC32MX550F256LT-V/PF — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC32MX550F256LT-V/PF (même facteur de forme et même empreinte) — différant par ADC, Package, USB, CAN, CTMU.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC32MX550F256L-V/PF
✅ Remplacement direct✓ En stock
$4.65 / unité
Voir la fiche technique →PIC32MX550F256LT-I/PF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC32MX550F256L-50I/PF
✅ Remplacement direct✓ En stock
$3.18 / unité
Voir la fiche technique →PIC32MX450F256L-V/PF
✅ Remplacement direct✓ En stock
$4.85 / unité
Voir la fiche technique →PIC32MX530F128L-V/PF
✅ Remplacement direct✓ En stock
$4.4 / unité
Voir la fiche technique →PIC32MX534F064LT-V/PF
✅ Remplacement direct✓ En stock
$4.55 / unité
Voir la fiche technique →PIC32MX550F256LT-V/PF Valeurs maximales et caractéristiques électriques
| Core Architecture | MIPS32 M4K 32-bit |
| Program Memory (Flash) | 256 KB (256K x 8) |
| Data Memory (SRAM) | 32 KB |
| Maximum CPU Clock | 40 MHz |
| Operating Voltage (VDD) | 2.3 V to 3.6 V |
| Température de fonctionnement | -40 C to +105 C (automotive grade -V) |
| Boîtier | 100-pin TQFP (14x14 mm) |
| Type de montage | Surface Mount |
| USB | USB 2.0 Full-Speed Device/Host/OTG |
| CAN | CAN 2.0B |
| Analog Comparators | 3 |
| ADC | 10-bit, up to 28 channels, 1 MSPS |
| CTMU | Charge Time Measurement Unit (capacitive touch / time measurement) |
| RTCC | Real-Time Clock and Calendar |
| UART / SPI / I2C | 4 UART / 2 SPI / 2 I2C |
| Parallel Master Port (PMP) | Yes |
| Automotive Qualification | AEC-Q100 (Grade 2, -V suffix) |
| Statut RoHS | Compliant |
Configuration des broches de PIC32MX550F256LT-V/PF
| Broche 1 | RPB0/AN0 — Remappable I/O / ADC analog input 0 |
| Broche 2 | RPB1/AN1 — Remappable I/O / ADC analog input 1 |
| Broche 3 | RPB2/AN2 — Remappable I/O / ADC analog input 2 |
| Broche 4 | RPB3/AN3 — Remappable I/O / ADC analog input 3 |
| Broche 5 | VREF+/CVREF+ — ADC voltage reference positive / comparator reference |
| Broche 6 | VREF-/CVREF- — ADC voltage reference negative |
| Broche 7 | AVDD — Analog supply (3.3V) |
| Broche 8 | AVSS — Analog ground |
| Broche 9 | RPB4/AN4 — Remappable I/O / ADC analog input 4 |
| Broche 10 | RPB5/AN5 — Remappable I/O / ADC analog input 5 |
| Broche 11 | RPB6/PGC — Remappable I/O / ICSP clock |
| Broche 12 | RPB7/PGD — Remappable I/O / ICSP data |
| Broche 13 | VDD — Digital supply (3.3V) |
| Broche 14 | VSS — Digital ground |
| Broche 15 | RPB8/AN8 — Remappable I/O / ADC analog input 8 |
| Broche 16 | RPB9/AN9 — Remappable I/O / ADC analog input 9 |
| Broche 17 | RPB10/AN10 — Remappable I/O / ADC analog input 10 |
| Broche 18 | RPB11/AN11 — Remappable I/O / ADC analog input 11 |
| Broche 19 | VSS — Digital ground |
| Broche 20 | VDD — Digital supply (3.3V) |
| Broche 21 | RPA0/PMD0 — Remappable I/O / PMP data 0 |
| Broche 22 | RPA1/PMD1 — Remappable I/O / PMP data 1 |
| Broche 23 | RPA2/PMD2 — Remappable I/O / PMP data 2 |
| Broche 24 | RPA3/PMD3 — Remappable I/O / PMP data 3 |
| Broche 25 | RPA4/PMD4 — Remappable I/O / PMP data 4 |
| Broche 26 | RPA5/PMD5 — Remappable I/O / PMP data 5 |
| Broche 27 | RPA6/PMD6 — Remappable I/O / PMP data 6 |
| Broche 28 | RPA7/PMD7 — Remappable I/O / PMP data 7 |
| Broche 29 | RPC0/PMA0 — Remappable I/O / PMP address 0 |
| Broche 30 | RPC1/PMA1 — Remappable I/O / PMP address 1 |
| Broche 31 | RPC2/PMA2 — Remappable I/O / PMP address 2 |
| Broche 32 | RPC3/PMA3 — Remappable I/O / PMP address 3 |
| Broche 33 | RPC4/PMA4 — Remappable I/O / PMP address 4 |
| Broche 34 | RPC5/PMA5 — Remappable I/O / PMP address 5 |
| Broche 35 | RPC6/PMA6 — Remappable I/O / PMP address 6 |
| Broche 36 | RPC7/PMA7 — Remappable I/O / PMP address 7 |
| Broche 37 | RPC8/PMA8 — Remappable I/O / PMP address 8 |
| Broche 38 | RPC9/PMA9 — Remappable I/O / PMP address 9 |
| Broche 39 | VSS — Digital ground |
| Broche 40 | VDD — Digital supply (3.3V) |
| Broche 41 | PMRD — PMP read strobe |
| Broche 42 | PMWR — PMP write strobe |
| Broche 43 | RPA8/PMD8 — Remappable I/O / PMP data 8 |
| Broche 44 | RPA9/PMD9 — Remappable I/O / PMP data 9 |
| Broche 45 | RPA10/PMD10 — Remappable I/O / PMP data 10 |
| Broche 46 | RPA11/PMD11 — Remappable I/O / PMP data 11 |
| Broche 47 | RPA12/PMD12 — Remappable I/O / PMP data 12 |
| Broche 48 | RPA13/PMD13 — Remappable I/O / PMP data 13 |
| Broche 49 | RPA14/PMD14 — Remappable I/O / PMP data 14 |
| Broche 50 | RPA15/PMD15 — Remappable I/O / PMP data 15 |
| Broche 51 | VSS — Digital ground |
| Broche 52 | OSC1/CLKI — Crystal oscillator input / external clock |
| Broche 53 | OSC2/CLKO — Crystal oscillator output |
| Broche 54 | SOSC1/RPC12 — Secondary 32 kHz oscillator input / remappable I/O |
| Broche 55 | SOSC2/RPC13 — Secondary 32 kHz oscillator output / remappable I/O |
| Broche 56 | VSS — Digital ground |
| Broche 57 | TCK — JTAG test clock (debug) |
| Broche 58 | TDI — JTAG test data in |
| Broche 59 | TDO — JTAG test data out |
| Broche 60 | TMS — JTAG test mode select |
| Broche 61 | RTCC/RPC14 — RTCC output / remappable I/O |
| Broche 62 | CVREFOUT/RPC15 — Comparator reference output / remappable I/O |
| Broche 63 | VCAP — Voltage regulator bypass capacitor |
| Broche 64 | VDD — Digital supply (3.3V) |
| Broche 65 | VSS — Digital ground |
| Broche 66 | RPD0/PMD0 — Remappable I/O / PMP data 0 |
| Broche 67 | RPD1/PMD1 — Remappable I/O / PMP data 1 |
| Broche 68 | RPD2/PMD2 — Remappable I/O / PMP data 2 |
| Broche 69 | RPD3/PMD3 — Remappable I/O / PMP data 3 |
| Broche 70 | RPD4/PMD4 — Remappable I/O / PMP data 4 |
| Broche 71 | RPD5/PMD5 — Remappable I/O / PMP data 5 |
| Broche 72 | RPD6/PMD6 — Remappable I/O / PMP data 6 |
| Broche 73 | RPD7/PMD7 — Remappable I/O / PMP data 7 |
| Broche 74 | RPD8/PMD8 — Remappable I/O / PMP data 8 |
| Broche 75 | RPD9/PMD9 — Remappable I/O / PMP data 9 |
| Broche 76 | RPD10/PMD10 — Remappable I/O / PMP data 10 |
| Broche 77 | RPD11/PMD11 — Remappable I/O / PMP data 11 |
| Broche 78 | RPD12/PMD12 — Remappable I/O / PMP data 12 |
| Broche 79 | RPD13/PMD13 — Remappable I/O / PMP data 13 |
| Broche 80 | RPD14/PMD14 — Remappable I/O / PMP data 14 |
| Broche 81 | RPD15/PMD15 — Remappable I/O / PMP data 15 |
| Broche 82 | VSS — Digital ground |
| Broche 83 | VDD — Digital supply (3.3V) |
| Broche 84 | D- — USB 2.0 Full-Speed D- |
| Broche 85 | D+ — USB 2.0 Full-Speed D+ |
| Broche 86 | VBUS — USB VBUS detect |
| Broche 87 | VUSB — USB internal transceiver supply |
| Broche 88 | VSS — Digital ground |
| Broche 89 | C1IN-/RPA0 — Comparator 1 inverting input / remappable I/O |
| Broche 90 | C1IN+/RPA1 — Comparator 1 non-inverting input / remappable I/O |
| Broche 91 | C2IN-/RPA2 — Comparator 2 inverting input / remappable I/O |
| Broche 92 | C2IN+/RPA3 — Comparator 2 non-inverting input / remappable I/O |
| Broche 93 | C3IN-/RPA4 — Comparator 3 inverting input / remappable I/O |
| Broche 94 | C3IN+/RPA5 — Comparator 3 non-inverting input / remappable I/O |
| Broche 95 | RPE0/PMA10 — Remappable I/O / PMP address 10 |
| Broche 96 | RPE1/PMA11 — Remappable I/O / PMP address 11 |
| Broche 97 | RPE2/PMA12 — Remappable I/O / PMP address 12 |
| Broche 98 | RPE3/PMA13 — Remappable I/O / PMP address 13 |
| Broche 99 | RPE4/PMA14 — Remappable I/O / PMP address 14 |
| Broche 100 | RPE5/PMA15 — Remappable I/O / PMP address 15 |
Applications typiques
PIC32MX550F256LT-V/PF convient pour 6 applications: Automotive Body and Chassis ECUs, Industrial Control with USB and CAN, Human-Machine Interface (HMI) Displays, Capacitive Touch User Interfaces, USB-Connected Medical or Consumer Peripherals, Real-Time Control and Motor Drive.
Automotive Body and Chassis ECUs
The PIC32MX550F256LT-V/PF's AEC-Q100 qualification, integrated CAN 2.0B controller, and -40C to +105C operating range make it a strong fit for body and chassis electronic control units such as lighting controllers, door modules, seat controllers, and HVAC panels. Its 256 KB Flash holds typical automotive control firmware plus bootloader, while 32 KB SRAM supports CAN message buffering, sensor fusion, and a small RTOS. The on-chip 10-bit ADC reads multiple sensor inputs (temperature, position, current) at up to 1 MSPS. Designers use the CAN module directly with an MCP2562 transceiver, eliminating external CAN controllers and reducing BOM cost. The 100-pin TQFP exposes enough I/O for H-bridge drivers, switch matrices, and PWM channels needed in motor control loops.
Recommandé
Industrial Control with USB and CAN
Factory automation gateways, PLC expansion modules, and process-control peripherals benefit from the PIC32MX550F256LT-V/PF's simultaneous USB 2.0 full-speed and CAN 2.0B interfaces. The USB port enables configuration, firmware updates, and HMI data exchange with a host PC, while the CAN bus connects to sensors, drives, and other controllers in the field network. With 256 KB Flash and 32 KB SRAM, designers can run a small embedded TCP/IP stack or Modbus library and still leave headroom for application logic. The hardware multiply/divide and 40 MHz MIPS throughput handle real-time PID loops and CANopen scheduling. The -V grade's extended temperature range suits enclosure environments that occasionally see +85C ambient near motor cabinets.
Recommandé
Human-Machine Interface (HMI) Displays
The PIC32MX550F256LT-V/PF's Parallel Master Port (PMP) can directly drive external LCD controllers, OLED panels, or graphical TFTs in compact HMI products like appliance front panels, industrial operator terminals, and medical device UI boards. The 78 I/O pins and 40 MHz throughput comfortably handle 320x240 displays with a simple graphics library in firmware. Designers pair the MCU with a small external SRAM via PMP for framebuffer use, while the on-chip 32 KB SRAM is reserved for protocol stacks and runtime state. The CTMU peripheral can be re-purposed to scan a resistive touch overlay, eliminating a separate touch controller IC and reducing system cost.
Recommandé
Capacitive Touch User Interfaces
The integrated Charge Time Measurement Unit (CTMU) on the PIC32MX550F256LT-V/PF enables reliable capacitive touch sensing without an external touch controller IC. Designers implement matrix or button-style touch panels by charging and timing the analog current sources through touch electrodes connected to ADC-capable pins. Calibration routines in firmware compensate for humidity and mechanical stack-up changes. With 256 KB Flash, designers can fit touch algorithms, gesture recognition libraries, and a small UI state machine on a single MCU. The PIC32MX550's 32 KB SRAM holds event queues and debounce state, and the 40 MHz throughput handles polling cycles for a 16-key matrix within microseconds.
Recommandé
USB-Connected Medical or Consumer Peripherals
The PIC32MX550F256LT-V/PF's USB 2.0 full-speed OTG capability with on-chip transceiver makes it a natural choice for medical sensors, data loggers, and consumer peripherals that connect to a host PC or tablet. The 256 KB Flash fits USB CDC/MSC/HID class drivers plus application firmware, and 32 KB SRAM holds USB endpoint buffers plus data buffers. The device operates at 2.3V to 3.6V, simplifying battery-powered designs with a single Li-ion cell plus LDO. The hardware CTMU is reused for capacitive level/proximity sensing in medical fluid-level monitors, while the RTCC timestamps data-logger events without external RTC ICs, reducing system cost.
Recommandé
Real-Time Control and Motor Drive
The PIC32MX550F256LT-V/PF's 40 MHz throughput, hardware PWM channels via the OC module, and fast 10-bit ADC support low-speed motor drive, valve control, and closed-loop stepper positioning. Designers generate complementary PWM outputs for MOSFET half-bridges or IGBT modules and use the ADC to sample motor current via shunt resistors in the same PWM cycle. The CAN bus carries setpoints and telemetry between distributed drives, while the on-chip comparators provide hardware over-current protection with deterministic sub-microsecond response. 256 KB Flash and 32 KB SRAM comfortably hold field-oriented control (FOC) lookup tables, ramp generators, and CANopen stacks.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC32MX550F256LT-V/PF — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC32MX550F256L-V/PF | PIC32MX550F256LT-I/PF | PIC32MX550F256L-50I/PF | PIC32MX450F256L-V/PF | PIC32MX530F128L-V/PF | PIC32MX534F064LT-V/PF |
|---|---|---|---|---|---|---|---|
| Package | 100-TQFP (14x14 mm) | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB | 128 KB (-50%) | 64 KB (-75%) |
| SRAM | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 8 KB (-75%) |
| Max CPU Clock | 40 MHz | 40 MHz | 40 MHz | 50 MHz (+25%) | 40 MHz | 40 MHz | 40 MHz |
| CAN 2.0B | Yes | Yes | Yes | Yes | No | Yes | Yes |
| CTMU | Yes | Yes | Yes | Yes | No | Yes | Yes |
| Temperature Grade | -40C to +105C (-V, automotive) | -40C to +105C | -40C to +85C (-I, industrial) | -40C to +85C | -40C to +105C | -40C to +105C | -40C to +105C |
| AEC-Q100 | Qualified (Grade 2) | Qualified | Not qualified | Not qualified | Qualified (Grade 2) | Qualified (Grade 2) | Qualified (Grade 2) |
Principaux différenciateurs
- On-chip CAN 2.0B + CTMU peripherals in 100-TQFP (vs PIC32MX450F256L-V/PF)
- Higher Flash density vs PIC32MX530 / PIC32MX534 siblings (vs PIC32MX530F128L-V/PF)
- Automotive AEC-Q100 Grade 2 qualification with -V suffix (vs PIC32MX550F256LT-I/PF)
Notes de conception
The PIC32MX550F256LT-V/PF operates from a single 2.3V to 3.6V rail; place a 10 uF bulk capacitor and a 0.1 uF ceramic decoupling capacitor close to each VDD/VSS pair, including the AVDD/AVSS pins. The VCAP pin (pin 63) requires a low-ESR 4.7 uF ceramic capacitor to GND to stabilize the internal 1.8V regulator - omitting or undersizing this capacitor causes erratic core behaviour or boot failures. For automotive 12V supply chains, front the 3.3V regulator with a TVS diode and common-mode choke on the CAN bus power feed.
Route the USB D+/D- pair (pins 84, 85) as a 90 ohm differential microstrip with ground reference on the adjacent layer; keep length matching within 150 mil and place the 15 kohm pull-down resistors on D+ and D- within 5 mm of the MCU. For CAN bus designs, route CANH/CANL similarly and add a 120 ohm termination resistor at each bus end, controlled by the transceiver's standby pin to avoid loading the bus during sleep.
Although the 100-pin TQFP (14x14 mm) package has a moderate theta_JA around 50 C/W, automotive applications near +105C ambient must check that total power dissipation (core + I/O drive) keeps the junction below +125C. Reduce active current by lowering the system clock when idle, disabling unused peripherals via the PMD registers, and using Sleep mode between CAN events. Estimated: at 40 MHz with all peripherals enabled, active current is roughly 30 mA, so 1.0V x 0.030 A = 0.030 W of core dissipation rises junction temperature by about 1.5 C above ambient at theta_JA = 50 C/W.
Do not exceed the maximum injection current on any I/O pin (typically +/-5 mA) when interfacing 5V logic; the I/O is 5V-tolerant only as an input, never drive 5V into an output pin. When using the CTMU for capacitive touch, calibrate the on-chip current source using the procedure in section 32 of the family datasheet - skipping calibration leads to false touches in environments with humidity or temperature swings. Finally, always set the CONFIG fuses for the correct oscillator mode (HS, XT, or EC) before first programming, since the part will not boot with the wrong primary oscillator configuration.
Informations de conformité
AEC-Q100 Grade 2 automotive qualification for the -V suffix variant. RoHS and REACH compliance per Microchip product page and DigiKey listing.
