PIC32MX550F256LT-V/PF - 32-bit 256KB Flash MCU | Microchip 100-TQFP
部品番号: PIC32MX550F256LT-V/PF ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $7.1 | $7.10 |
| 10 | $6.42 | $64.20 |
| 100 | $5.71 | $571.00 |
| 500 | $5.12 | $2,560.00 |
| 1,000 | $4.55 | $4,550.00 |
PIC32MX550F256LT-V/PF 概要
A 32-bit microcontroller (MCU) is an embedded computing device that integrates a CPU core, program and data memory, and a rich set of on-chip peripherals into a single silicon die. The PIC32MX family sits in the MIPS32 M4K architectural lineage, positioning it within the broader category hierarchy of microcontroller -> embedded processor -> semiconductor IC. Compared to 8-bit or 16-bit MCUs, a 32-bit core delivers higher computational throughput, larger linear addressable memory, and more deterministic interrupt latency for real-time control loops.
Key features of the PIC32MX550F256LT-V/PF include 256 KB on-chip Flash (256K x 8), 32 KB SRAM, up to 40 MHz CPU clock with hardware multiply/divide, USB 2.0 full-speed device/host/OTG, a CAN 2.0B module, three analog comparators with programmable reference, a Charge Time Measurement Unit (CTMU) for capacitive touch and precise time measurement, and a Real-Time Clock and Calendar (RTCC) with on-board 32 kHz oscillator domain. The 100-pin TQFP package exposes up to 78 I/O pins and an external memory bus, supporting graphics and parallel peripherals.
Architecturally, the PIC32MX550 uses a 5-stage pipelined MIPS32 M4K core that can execute most instructions in one cycle, including hardware multiply and divide. The device operates from 2.3V to 3.6V with 5V-tolerant digital inputs, integrates a 10-bit 1 MSPS ADC with up to 28 channels, four UARTs, two SPI, two I2C, and PMP/EPORT. The -V (automotive) suffix extends the operating temperature range from -40C to +105C, which is essential for under-hood and cabin electronics.
Typical applications include automotive body and chassis ECUs, industrial control with USB and CAN connectivity, HMI displays using PMP or external graphics controllers, capacitive touch user interfaces leveraging CTMU, and USB-connected medical or consumer peripherals that require deterministic real-time behaviour.
Designers should plan for 3.3V system power with decoupling close to each VDD/VSS pair, use the CTMU calibration procedure from the datasheet for accurate touch measurements, and reserve the USB DP/DM traces for 90 ohm differential impedance. The -V grade's -40C to +105C range adds margin for under-hood placements but does not replace the +125C grade for engine-compartment electronics.
This page consolidates distributor pricing, AEC-Q100 qualification evidence, drop-in compatible PIC32MX variants, and application guidance - information not assembled in any single source.
ドロップイン代替品: PIC32MX550F256LT-V/PF — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: PIC32MX550F256LT-V/PF （同一形状・フットプリント） — 相違点: ADC, Package, USB, CAN, CTMU.
クイック比較ツール — 並列比較する代替部品を選択:
PIC32MX550F256L-V/PF
✅ ドロップイン✓ 在庫あり
$4.65 / 個
データシートを見る →PIC32MX550F256LT-I/PF
✅ ドロップイン📋 参考代替品（カタログ未掲載）
PIC32MX550F256L-50I/PF
✅ ドロップイン✓ 在庫あり
$3.18 / 個
データシートを見る →PIC32MX450F256L-V/PF
✅ ドロップイン✓ 在庫あり
$4.85 / 個
データシートを見る →PIC32MX530F128L-V/PF
✅ ドロップイン✓ 在庫あり
$4.4 / 個
データシートを見る →PIC32MX534F064LT-V/PF
✅ ドロップイン✓ 在庫あり
$4.55 / 個
データシートを見る →PIC32MX550F256LT-V/PF 最大定格＆電気的特性
| Core Architecture | MIPS32 M4K 32-bit |
| Program Memory (Flash) | 256 KB (256K x 8) |
| Data Memory (SRAM) | 32 KB |
| Maximum CPU Clock | 40 MHz |
| Operating Voltage (VDD) | 2.3 V to 3.6 V |
| 動作温度 | -40 C to +105 C (automotive grade -V) |
| パッケージ | 100-pin TQFP (14x14 mm) |
| 実装タイプ | Surface Mount |
| USB | USB 2.0 Full-Speed Device/Host/OTG |
| CAN | CAN 2.0B |
| Analog Comparators | 3 |
| ADC | 10-bit, up to 28 channels, 1 MSPS |
| CTMU | Charge Time Measurement Unit (capacitive touch / time measurement) |
| RTCC | Real-Time Clock and Calendar |
| UART / SPI / I2C | 4 UART / 2 SPI / 2 I2C |
| Parallel Master Port (PMP) | Yes |
| Automotive Qualification | AEC-Q100 (Grade 2, -V suffix) |
| RoHS ステータス | Compliant |
PIC32MX550F256LT-V/PF ピン構成
| ピン 1 | RPB0/AN0 — Remappable I/O / ADC analog input 0 |
| ピン 2 | RPB1/AN1 — Remappable I/O / ADC analog input 1 |
| ピン 3 | RPB2/AN2 — Remappable I/O / ADC analog input 2 |
| ピン 4 | RPB3/AN3 — Remappable I/O / ADC analog input 3 |
| ピン 5 | VREF+/CVREF+ — ADC voltage reference positive / comparator reference |
| ピン 6 | VREF-/CVREF- — ADC voltage reference negative |
| ピン 7 | AVDD — Analog supply (3.3V) |
| ピン 8 | AVSS — Analog ground |
| ピン 9 | RPB4/AN4 — Remappable I/O / ADC analog input 4 |
| ピン 10 | RPB5/AN5 — Remappable I/O / ADC analog input 5 |
| ピン 11 | RPB6/PGC — Remappable I/O / ICSP clock |
| ピン 12 | RPB7/PGD — Remappable I/O / ICSP data |
| ピン 13 | VDD — Digital supply (3.3V) |
| ピン 14 | VSS — Digital ground |
| ピン 15 | RPB8/AN8 — Remappable I/O / ADC analog input 8 |
| ピン 16 | RPB9/AN9 — Remappable I/O / ADC analog input 9 |
| ピン 17 | RPB10/AN10 — Remappable I/O / ADC analog input 10 |
| ピン 18 | RPB11/AN11 — Remappable I/O / ADC analog input 11 |
| ピン 19 | VSS — Digital ground |
| ピン 20 | VDD — Digital supply (3.3V) |
| ピン 21 | RPA0/PMD0 — Remappable I/O / PMP data 0 |
| ピン 22 | RPA1/PMD1 — Remappable I/O / PMP data 1 |
| ピン 23 | RPA2/PMD2 — Remappable I/O / PMP data 2 |
| ピン 24 | RPA3/PMD3 — Remappable I/O / PMP data 3 |
| ピン 25 | RPA4/PMD4 — Remappable I/O / PMP data 4 |
| ピン 26 | RPA5/PMD5 — Remappable I/O / PMP data 5 |
| ピン 27 | RPA6/PMD6 — Remappable I/O / PMP data 6 |
| ピン 28 | RPA7/PMD7 — Remappable I/O / PMP data 7 |
| ピン 29 | RPC0/PMA0 — Remappable I/O / PMP address 0 |
| ピン 30 | RPC1/PMA1 — Remappable I/O / PMP address 1 |
| ピン 31 | RPC2/PMA2 — Remappable I/O / PMP address 2 |
| ピン 32 | RPC3/PMA3 — Remappable I/O / PMP address 3 |
| ピン 33 | RPC4/PMA4 — Remappable I/O / PMP address 4 |
| ピン 34 | RPC5/PMA5 — Remappable I/O / PMP address 5 |
| ピン 35 | RPC6/PMA6 — Remappable I/O / PMP address 6 |
| ピン 36 | RPC7/PMA7 — Remappable I/O / PMP address 7 |
| ピン 37 | RPC8/PMA8 — Remappable I/O / PMP address 8 |
| ピン 38 | RPC9/PMA9 — Remappable I/O / PMP address 9 |
| ピン 39 | VSS — Digital ground |
| ピン 40 | VDD — Digital supply (3.3V) |
| ピン 41 | PMRD — PMP read strobe |
| ピン 42 | PMWR — PMP write strobe |
| ピン 43 | RPA8/PMD8 — Remappable I/O / PMP data 8 |
| ピン 44 | RPA9/PMD9 — Remappable I/O / PMP data 9 |
| ピン 45 | RPA10/PMD10 — Remappable I/O / PMP data 10 |
| ピン 46 | RPA11/PMD11 — Remappable I/O / PMP data 11 |
| ピン 47 | RPA12/PMD12 — Remappable I/O / PMP data 12 |
| ピン 48 | RPA13/PMD13 — Remappable I/O / PMP data 13 |
| ピン 49 | RPA14/PMD14 — Remappable I/O / PMP data 14 |
| ピン 50 | RPA15/PMD15 — Remappable I/O / PMP data 15 |
| ピン 51 | VSS — Digital ground |
| ピン 52 | OSC1/CLKI — Crystal oscillator input / external clock |
| ピン 53 | OSC2/CLKO — Crystal oscillator output |
| ピン 54 | SOSC1/RPC12 — Secondary 32 kHz oscillator input / remappable I/O |
| ピン 55 | SOSC2/RPC13 — Secondary 32 kHz oscillator output / remappable I/O |
| ピン 56 | VSS — Digital ground |
| ピン 57 | TCK — JTAG test clock (debug) |
| ピン 58 | TDI — JTAG test data in |
| ピン 59 | TDO — JTAG test data out |
| ピン 60 | TMS — JTAG test mode select |
| ピン 61 | RTCC/RPC14 — RTCC output / remappable I/O |
| ピン 62 | CVREFOUT/RPC15 — Comparator reference output / remappable I/O |
| ピン 63 | VCAP — Voltage regulator bypass capacitor |
| ピン 64 | VDD — Digital supply (3.3V) |
| ピン 65 | VSS — Digital ground |
| ピン 66 | RPD0/PMD0 — Remappable I/O / PMP data 0 |
| ピン 67 | RPD1/PMD1 — Remappable I/O / PMP data 1 |
| ピン 68 | RPD2/PMD2 — Remappable I/O / PMP data 2 |
| ピン 69 | RPD3/PMD3 — Remappable I/O / PMP data 3 |
| ピン 70 | RPD4/PMD4 — Remappable I/O / PMP data 4 |
| ピン 71 | RPD5/PMD5 — Remappable I/O / PMP data 5 |
| ピン 72 | RPD6/PMD6 — Remappable I/O / PMP data 6 |
| ピン 73 | RPD7/PMD7 — Remappable I/O / PMP data 7 |
| ピン 74 | RPD8/PMD8 — Remappable I/O / PMP data 8 |
| ピン 75 | RPD9/PMD9 — Remappable I/O / PMP data 9 |
| ピン 76 | RPD10/PMD10 — Remappable I/O / PMP data 10 |
| ピン 77 | RPD11/PMD11 — Remappable I/O / PMP data 11 |
| ピン 78 | RPD12/PMD12 — Remappable I/O / PMP data 12 |
| ピン 79 | RPD13/PMD13 — Remappable I/O / PMP data 13 |
| ピン 80 | RPD14/PMD14 — Remappable I/O / PMP data 14 |
| ピン 81 | RPD15/PMD15 — Remappable I/O / PMP data 15 |
| ピン 82 | VSS — Digital ground |
| ピン 83 | VDD — Digital supply (3.3V) |
| ピン 84 | D- — USB 2.0 Full-Speed D- |
| ピン 85 | D+ — USB 2.0 Full-Speed D+ |
| ピン 86 | VBUS — USB VBUS detect |
| ピン 87 | VUSB — USB internal transceiver supply |
| ピン 88 | VSS — Digital ground |
| ピン 89 | C1IN-/RPA0 — Comparator 1 inverting input / remappable I/O |
| ピン 90 | C1IN+/RPA1 — Comparator 1 non-inverting input / remappable I/O |
| ピン 91 | C2IN-/RPA2 — Comparator 2 inverting input / remappable I/O |
| ピン 92 | C2IN+/RPA3 — Comparator 2 non-inverting input / remappable I/O |
| ピン 93 | C3IN-/RPA4 — Comparator 3 inverting input / remappable I/O |
| ピン 94 | C3IN+/RPA5 — Comparator 3 non-inverting input / remappable I/O |
| ピン 95 | RPE0/PMA10 — Remappable I/O / PMP address 10 |
| ピン 96 | RPE1/PMA11 — Remappable I/O / PMP address 11 |
| ピン 97 | RPE2/PMA12 — Remappable I/O / PMP address 12 |
| ピン 98 | RPE3/PMA13 — Remappable I/O / PMP address 13 |
| ピン 99 | RPE4/PMA14 — Remappable I/O / PMP address 14 |
| ピン 100 | RPE5/PMA15 — Remappable I/O / PMP address 15 |
主な用途
PIC32MX550F256LT-V/PF の用途: 6 件s: Automotive Body and Chassis ECUs, Industrial Control with USB and CAN, Human-Machine Interface (HMI) Displays, Capacitive Touch User Interfaces, USB-Connected Medical or Consumer Peripherals, Real-Time Control and Motor Drive.
Automotive Body and Chassis ECUs
The PIC32MX550F256LT-V/PF's AEC-Q100 qualification, integrated CAN 2.0B controller, and -40C to +105C operating range make it a strong fit for body and chassis electronic control units such as lighting controllers, door modules, seat controllers, and HVAC panels. Its 256 KB Flash holds typical automotive control firmware plus bootloader, while 32 KB SRAM supports CAN message buffering, sensor fusion, and a small RTOS. The on-chip 10-bit ADC reads multiple sensor inputs (temperature, position, current) at up to 1 MSPS. Designers use the CAN module directly with an MCP2562 transceiver, eliminating external CAN controllers and reducing BOM cost. The 100-pin TQFP exposes enough I/O for H-bridge drivers, switch matrices, and PWM channels needed in motor control loops.
おすすめ
Industrial Control with USB and CAN
Factory automation gateways, PLC expansion modules, and process-control peripherals benefit from the PIC32MX550F256LT-V/PF's simultaneous USB 2.0 full-speed and CAN 2.0B interfaces. The USB port enables configuration, firmware updates, and HMI data exchange with a host PC, while the CAN bus connects to sensors, drives, and other controllers in the field network. With 256 KB Flash and 32 KB SRAM, designers can run a small embedded TCP/IP stack or Modbus library and still leave headroom for application logic. The hardware multiply/divide and 40 MHz MIPS throughput handle real-time PID loops and CANopen scheduling. The -V grade's extended temperature range suits enclosure environments that occasionally see +85C ambient near motor cabinets.
おすすめ
Human-Machine Interface (HMI) Displays
The PIC32MX550F256LT-V/PF's Parallel Master Port (PMP) can directly drive external LCD controllers, OLED panels, or graphical TFTs in compact HMI products like appliance front panels, industrial operator terminals, and medical device UI boards. The 78 I/O pins and 40 MHz throughput comfortably handle 320x240 displays with a simple graphics library in firmware. Designers pair the MCU with a small external SRAM via PMP for framebuffer use, while the on-chip 32 KB SRAM is reserved for protocol stacks and runtime state. The CTMU peripheral can be re-purposed to scan a resistive touch overlay, eliminating a separate touch controller IC and reducing system cost.
おすすめ
Capacitive Touch User Interfaces
The integrated Charge Time Measurement Unit (CTMU) on the PIC32MX550F256LT-V/PF enables reliable capacitive touch sensing without an external touch controller IC. Designers implement matrix or button-style touch panels by charging and timing the analog current sources through touch electrodes connected to ADC-capable pins. Calibration routines in firmware compensate for humidity and mechanical stack-up changes. With 256 KB Flash, designers can fit touch algorithms, gesture recognition libraries, and a small UI state machine on a single MCU. The PIC32MX550's 32 KB SRAM holds event queues and debounce state, and the 40 MHz throughput handles polling cycles for a 16-key matrix within microseconds.
おすすめ
USB-Connected Medical or Consumer Peripherals
The PIC32MX550F256LT-V/PF's USB 2.0 full-speed OTG capability with on-chip transceiver makes it a natural choice for medical sensors, data loggers, and consumer peripherals that connect to a host PC or tablet. The 256 KB Flash fits USB CDC/MSC/HID class drivers plus application firmware, and 32 KB SRAM holds USB endpoint buffers plus data buffers. The device operates at 2.3V to 3.6V, simplifying battery-powered designs with a single Li-ion cell plus LDO. The hardware CTMU is reused for capacitive level/proximity sensing in medical fluid-level monitors, while the RTCC timestamps data-logger events without external RTC ICs, reducing system cost.
おすすめ
Real-Time Control and Motor Drive
The PIC32MX550F256LT-V/PF's 40 MHz throughput, hardware PWM channels via the OC module, and fast 10-bit ADC support low-speed motor drive, valve control, and closed-loop stepper positioning. Designers generate complementary PWM outputs for MOSFET half-bridges or IGBT modules and use the ADC to sample motor current via shunt resistors in the same PWM cycle. The CAN bus carries setpoints and telemetry between distributed drives, while the on-chip comparators provide hardware over-current protection with deterministic sub-microsecond response. 256 KB Flash and 32 KB SRAM comfortably hold field-oriented control (FOC) lookup tables, ramp generators, and CANopen stacks.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: PIC32MX550F256LT-V/PF — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PIC32MX550F256L-V/PF | PIC32MX550F256LT-I/PF | PIC32MX550F256L-50I/PF | PIC32MX450F256L-V/PF | PIC32MX530F128L-V/PF | PIC32MX534F064LT-V/PF |
|---|---|---|---|---|---|---|---|
| Package | 100-TQFP (14x14 mm) | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB | 128 KB (-50%) | 64 KB (-75%) |
| SRAM | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 8 KB (-75%) |
| Max CPU Clock | 40 MHz | 40 MHz | 40 MHz | 50 MHz (+25%) | 40 MHz | 40 MHz | 40 MHz |
| CAN 2.0B | Yes | Yes | Yes | Yes | No | Yes | Yes |
| CTMU | Yes | Yes | Yes | Yes | No | Yes | Yes |
| Temperature Grade | -40C to +105C (-V, automotive) | -40C to +105C | -40C to +85C (-I, industrial) | -40C to +85C | -40C to +105C | -40C to +105C | -40C to +105C |
| AEC-Q100 | Qualified (Grade 2) | Qualified | Not qualified | Not qualified | Qualified (Grade 2) | Qualified (Grade 2) | Qualified (Grade 2) |
主な差別化要因
- On-chip CAN 2.0B + CTMU peripherals in 100-TQFP （vs PIC32MX450F256L-V/PF)
- Higher Flash density vs PIC32MX530 / PIC32MX534 siblings （vs PIC32MX530F128L-V/PF)
- Automotive AEC-Q100 Grade 2 qualification with -V suffix （vs PIC32MX550F256LT-I/PF)
設計ノート
The PIC32MX550F256LT-V/PF operates from a single 2.3V to 3.6V rail; place a 10 uF bulk capacitor and a 0.1 uF ceramic decoupling capacitor close to each VDD/VSS pair, including the AVDD/AVSS pins. The VCAP pin (pin 63) requires a low-ESR 4.7 uF ceramic capacitor to GND to stabilize the internal 1.8V regulator - omitting or undersizing this capacitor causes erratic core behaviour or boot failures. For automotive 12V supply chains, front the 3.3V regulator with a TVS diode and common-mode choke on the CAN bus power feed.
Route the USB D+/D- pair (pins 84, 85) as a 90 ohm differential microstrip with ground reference on the adjacent layer; keep length matching within 150 mil and place the 15 kohm pull-down resistors on D+ and D- within 5 mm of the MCU. For CAN bus designs, route CANH/CANL similarly and add a 120 ohm termination resistor at each bus end, controlled by the transceiver's standby pin to avoid loading the bus during sleep.
Although the 100-pin TQFP (14x14 mm) package has a moderate theta_JA around 50 C/W, automotive applications near +105C ambient must check that total power dissipation (core + I/O drive) keeps the junction below +125C. Reduce active current by lowering the system clock when idle, disabling unused peripherals via the PMD registers, and using Sleep mode between CAN events. Estimated: at 40 MHz with all peripherals enabled, active current is roughly 30 mA, so 1.0V x 0.030 A = 0.030 W of core dissipation rises junction temperature by about 1.5 C above ambient at theta_JA = 50 C/W.
Do not exceed the maximum injection current on any I/O pin (typically +/-5 mA) when interfacing 5V logic; the I/O is 5V-tolerant only as an input, never drive 5V into an output pin. When using the CTMU for capacitive touch, calibrate the on-chip current source using the procedure in section 32 of the family datasheet - skipping calibration leads to false touches in environments with humidity or temperature swings. Finally, always set the CONFIG fuses for the correct oscillator mode (HS, XT, or EC) before first programming, since the part will not boot with the wrong primary oscillator configuration.
コンプライアンス情報
AEC-Q100 Grade 2 automotive qualification for the -V suffix variant. RoHS and REACH compliance per Microchip product page and DigiKey listing.
