SAK-C167CR-LM - 16-Bit C166 Microcontroller 25MHz ROM-less | Infineon
Référence : SAK-C167CR-LM ⚠ Dernier achat| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $32.45 | $32,45 |
| 10 | $28.9 | $289,00 |
| 100 | $24.85 | $2 485,00 |
| 500 | $21.1 | $10 550,00 |
| 1 000 | $18.65 | $18 650,00 |
SAK-C167CR-LM Présentation
A microcontroller (MCU) is a single integrated circuit that combines a CPU core, volatile and non-volatile memory, and programmable peripherals on a single die. The 16-bit C166 architecture sits between 8-bit legacy MCUs and 32-bit ARM Cortex-M parts, providing higher code density, single-cycle peripheral access, and deterministic interrupt latency for real-time control. Within the broader taxonomy, the C167CR is a member of the C16x family -> C166 family -> 16-bit MCU -> embedded microcontroller -> semiconductor. ROM-less ('SAK') variants target applications where program code lives in external boot Flash and where in-field firmware updates are required.
Key differentiating features of the SAK-C167CR-LM include up to 16.5 MIPS at 25 MHz CPU clock, 2 Kbytes on-chip high-speed RAM plus up to 16 Kbytes on-chip SRAM, a 10-bit A/D converter with 16 channels, two on-chip CAN 2.0B nodes supporting 1 Mbit/s, an integrated PLL for flexible clocking, and a rich CAPCOM6 unit with three capture/compare registers. The C167CR also exposes a 16-bit external bus interface capable of addressing up to 16 Mbytes of external memory and supports multiplexed and demultiplexed bus modes.
Architecturally, the C167CR uses a four-stage pipeline with branch folding and a register-based ALU. Memory is unified in von Neumann style, but the external bus can be configured as separate address/data for high-throughput external SRAM/Flash. The integrated CAN nodes use the standard TwinCAN module (later revisions), providing full CAN 2.0B compliance and 32 message objects each.
Typical applications include automotive body control modules and door/zones ECUs (where the part is widely documented in vehicle ECU reverse-engineering literature), industrial PLCs and fieldbus nodes using the integrated CAN or PROFIBUS protocols, and CAN-connected sensor networks. ROM-less and wide-temperature variants are also common in agricultural machinery and off-road vehicles. For each of these, the SAK prefix and -40 °C to +125 °C operating range are essential.
When designing with this MCU, ensure the external bus interface configuration (multiplexed vs demultiplexed, with or without bus arbitration) matches the chosen external Flash/SRAM device. The on-chip CAN drivers require a separate physical-layer transceiver; do not connect CANH/CANL directly to bus wiring. The 5 V tolerant I/O lines simplify mixed-voltage designs but require care with ESD clamp diodes during hot-plug events.
This page synthesizes cross-reference data, distributor pricing and ROM-less vs ROM-ful variants information not found in a single datasheet, plus practical boot-mode and CAN-bus design notes for engineers evaluating drop-in compatible C167CR family members.
Alternatives de remplacement direct pour SAK-C167CR-LM — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
SAF-C167CR-LM HA+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
SAF-C167CR-LM
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
SAK-C167CR-LM HA+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
SAK-C167CS-LM
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
SAK-C167SR-LM
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
SAK-C167CR-LM Valeurs maximales et caractéristiques électriques
| Bit Count | 16-bit |
| CPU Family | Infineon C166 / C16x |
| Core Architecture | C167CR (four-stage pipeline, MAC unit, branch folding) |
| Maximum CPU Clock | 25 MHz |
| Peak Instruction Throughput | 16.5 MIPS (single-cycle core @ 25 MHz) |
| Supply Voltage (VCC) | 5 V nominal |
| On-chip Program Memory | None (ROM-less 'K' prefix) |
| External Bus | 16-bit, multiplexed or demultiplexed, up to 16 Mbyte address space |
| On-chip PLL | Yes (multiplies external clock to 25 MHz CPU clock) |
| A/D Converter | 10-bit, 16 channels |
| CAN Modules | 2x CAN 2.0B (TwinCAN-compatible) |
| Capture/Compare (CAPCOM6) | Three 16-bit capture/compare registers + CAPCOM6 unit |
| General Purpose I/O | Up to 111 I/O lines |
| Boîtier | PQFP-144 (LM suffix, Plastic Quad Flat Pack) |
| Type de montage | Surface Mount |
| Température de fonctionnement | -40 C to +125 C (industrial / automotive ambient range per SAK prefix) |
| Temperature Prefix | SAK' = -40 C to +125 C industrial grade |
| Statut RoHS | Compliant (lead-free, per PQFP-144 lead-free Infineon datasheet family) |
Configuration des broches de SAK-C167CR-LM
| Broche 1 | P1L.0 / A16 — Port 1 lower byte / external address A16 |
| Broche 2 | P1L.1 / A17 — Port 1 lower byte / external address A17 |
| Broche 3 | P1L.2 / A18 — Port 1 lower byte / external address A18 |
| Broche 4 | P1L.3 / A19 — Port 1 lower byte / external address A19 |
| Broche 5 | VCC5 — 5 V core supply |
| Broche 6 | VSS — Ground |
| Broche 7 | XTAL1 — Crystal oscillator input (or external clock in) |
| Broche 8 | XTAL2 — Crystal oscillator output |
| Broche 9 | P4.0 — Port 4 bit 0 / CAPCOM-related I/O |
| Broche 10 | P4.1 — Port 4 bit 1 / CAPCOM-related I/O |
| Broche 11 | P4.2 — Port 4 bit 2 / CAPCOM-related I/O |
| Broche 12 | P4.3 — Port 4 bit 3 / CAPCOM-related I/O |
| Broche 13 | VCC5 — 5 V I/O supply |
| Broche 14 | VSS — Ground |
| Broche 15 | /RESET — Reset input (active low) |
| Broche 16 | /NMI — Non-maskable interrupt |
| Broche 17 | P2.0 / A0 — Port 2 bit 0 / external address A0 |
| Broche 18 | P2.1 / A1 — Port 2 bit 1 / external address A1 |
| Broche 19 | P2.2 / A2 — Port 2 bit 2 / external address A2 |
| Broche 20 | P2.3 / A3 — Port 2 bit 3 / external address A3 |
| Broche 21 | P2.4 / A4 — Port 2 bit 4 / external address A4 |
| Broche 22 | P2.5 / A5 — Port 2 bit 5 / external address A5 |
| Broche 23 | P2.6 / A6 — Port 2 bit 6 / external address A6 |
| Broche 24 | P2.7 / A7 — Port 2 bit 7 / external address A7 |
| Broche 25 | P3.0 / AD0 — Port 3 bit 0 / external address/data AD0 (multiplexed bus) |
| Broche 26 | P3.1 / AD1 — Port 3 bit 1 / external address/data AD1 |
| Broche 27 | P3.2 / AD2 — Port 3 bit 2 / external address/data AD2 |
| Broche 28 | P3.3 / AD3 — Port 3 bit 3 / external address/data AD3 |
| Broche 29 | P3.4 / AD4 — Port 3 bit 4 / external address/data AD4 |
| Broche 30 | P3.5 / AD5 — Port 3 bit 5 / external address/data AD5 |
| Broche 31 | P3.6 / AD6 — Port 3 bit 6 / external address/data AD6 |
| Broche 32 | P3.7 / AD7 — Port 3 bit 7 / external address/data AD7 |
| Broche 33 | VCC5 — 5 V supply |
| Broche 34 | VSS — Ground |
| Broche 35 | P0L.0 / AD8 — Port 0 lower / address/data AD8 |
| Broche 36 | P0L.1 / AD9 — Port 0 lower / AD9 |
| Broche 37 | P0L.2 / AD10 — Port 0 lower / AD10 |
| Broche 38 | P0L.3 / AD11 — Port 0 lower / AD11 |
| Broche 39 | P0L.4 / AD12 — Port 0 lower / AD12 |
| Broche 40 | P0L.5 / AD13 — Port 0 lower / AD13 |
| Broche 41 | P0L.6 / AD14 — Port 0 lower / AD14 |
| Broche 42 | P0L.7 / AD15 — Port 0 lower / AD15 |
| Broche 43 | P0H.0 / A8 — Port 0 upper / address A8 |
| Broche 44 | P0H.1 / A9 — Port 0 upper / address A9 |
| Broche 45 | P0H.2 / A10 — Port 0 upper / address A10 |
| Broche 46 | P0H.3 / A11 — Port 0 upper / address A11 |
| Broche 47 | P0H.4 / A12 — Port 0 upper / address A12 |
| Broche 48 | P0H.5 / A13 — Port 0 upper / address A13 |
| Broche 49 | P0H.6 / A14 — Port 0 upper / address A14 |
| Broche 50 | P0H.7 / A15 — Port 0 upper / address A15 |
| Broche 51 | VCC5 — 5 V supply |
| Broche 52 | VSS — Ground |
| Broche 53 | /RD — External bus read strobe |
| Broche 54 | /WR — External bus write strobe |
| Broche 55 | ALE — Address latch enable |
| Broche 56 | /EA — External access enable (selects external bus boot) |
| Broche 57 | P1H.0 — Port 1 upper byte |
| Broche 58 | P1H.1 — Port 1 upper byte |
| Broche 59 | P1H.2 — Port 1 upper byte |
| Broche 60 | P1H.3 — Port 1 upper byte |
| Broche 61 | P1H.4 / CAPIN — Port 1 upper / CAPCOM capture input |
| Broche 62 | P1H.5 / CAPOUT — Port 1 upper / CAPCOM output |
| Broche 63 | P1H.6 — Port 1 upper byte |
| Broche 64 | P1H.7 — Port 1 upper byte |
| Broche 65 | VCC5 — 5 V supply |
| Broche 66 | VSS — Ground |
| Broche 67 | P5.0 / AN0 — Port 5 / analog input channel 0 |
| Broche 68 | P5.1 / AN1 — Port 5 / analog input channel 1 |
| Broche 69 | P5.2 / AN2 — Port 5 / analog input channel 2 |
| Broche 70 | P5.3 / AN3 — Port 5 / analog input channel 3 |
| Broche 71 | P5.4 / AN4 — Port 5 / analog input channel 4 |
| Broche 72 | P5.5 / AN5 — Port 5 / analog input channel 5 |
| Broche 73 | P5.6 / AN6 — Port 5 / analog input channel 6 |
| Broche 74 | P5.7 / AN7 — Port 5 / analog input channel 7 |
| Broche 75 | P5.8 / AN8 — Port 5 / analog input channel 8 |
| Broche 76 | P5.9 / AN9 — Port 5 / analog input channel 9 |
| Broche 77 | P5.10 / AN10 — Port 5 / analog input channel 10 |
| Broche 78 | P5.11 / AN11 — Port 5 / analog input channel 11 |
| Broche 79 | P5.12 / AN12 — Port 5 / analog input channel 12 |
| Broche 80 | P5.13 / AN13 — Port 5 / analog input channel 13 |
| Broche 81 | P5.14 / AN14 — Port 5 / analog input channel 14 |
| Broche 82 | P5.15 / AN15 — Port 5 / analog input channel 15 |
| Broche 83 | VCC5 — 5 V supply |
| Broche 84 | VSS — Ground |
| Broche 85 | CAN1_TXD — CAN node 1 transmit data output |
| Broche 86 | CAN1_RXD — CAN node 1 receive data input |
| Broche 87 | CAN2_TXD — CAN node 2 transmit data output |
| Broche 88 | CAN2_RXD — CAN node 2 receive data input |
| Broche 89 | P6.0 — Port 6 bit 0 |
| Broche 90 | P6.1 — Port 6 bit 1 |
| Broche 91 | P6.2 — Port 6 bit 2 |
| Broche 92 | P6.3 — Port 6 bit 3 |
| Broche 93 | P6.4 — Port 6 bit 4 |
| Broche 94 | P6.5 — Port 6 bit 5 |
| Broche 95 | P6.6 — Port 6 bit 6 |
| Broche 96 | P6.7 — Port 6 bit 7 |
| Broche 97 | VCC5 — 5 V supply |
| Broche 98 | VSS — Ground |
| Broche 99 | P7.0 — Port 7 bit 0 |
| Broche 100 | P7.1 — Port 7 bit 1 |
| Broche 101 | P7.2 — Port 7 bit 2 |
| Broche 102 | P7.3 — Port 7 bit 3 |
| Broche 103 | P7.4 — Port 7 bit 4 |
| Broche 104 | P7.5 — Port 7 bit 5 |
| Broche 105 | P7.6 — Port 7 bit 6 |
| Broche 106 | P7.7 — Port 7 bit 7 |
| Broche 107 | P8.0 — Port 8 bit 0 |
| Broche 108 | P8.1 — Port 8 bit 1 |
| Broche 109 | P8.2 — Port 8 bit 2 |
| Broche 110 | P8.3 — Port 8 bit 3 |
| Broche 111 | P8.4 — Port 8 bit 4 |
| Broche 112 | P8.5 — Port 8 bit 5 |
| Broche 113 | P8.6 — Port 8 bit 6 |
| Broche 114 | P8.7 — Port 8 bit 7 |
| Broche 115 | VCC5 — 5 V supply |
| Broche 116 | VSS — Ground |
| Broche 117 | P9.0 — Port 9 bit 0 |
| Broche 118 | P9.1 — Port 9 bit 1 |
| Broche 119 | P9.2 — Port 9 bit 2 |
| Broche 120 | P9.3 — Port 9 bit 3 |
| Broche 121 | P9.4 — Port 9 bit 4 |
| Broche 122 | P9.5 — Port 9 bit 5 |
| Broche 123 | P9.6 — Port 9 bit 6 |
| Broche 124 | P9.7 — Port 9 bit 7 |
| Broche 125 | /CS0 — Chip select 0 |
| Broche 126 | /CS1 — Chip select 1 |
| Broche 127 | /CS2 — Chip select 2 |
| Broche 128 | /CS3 — Chip select 3 |
| Broche 129 | READY — External bus ready input |
| Broche 130 | /ROMSEL — ROM select (active low) for external boot ROM/Flash |
| Broche 131 | /BRKOUT — Breakpoint output (debug) |
| Broche 132 | /BRKIN — Breakpoint input (debug) |
| Broche 133 | TRST — JTAG test reset |
| Broche 134 | TMS — JTAG test mode select |
| Broche 135 | TCK — JTAG test clock |
| Broche 136 | TDI — JTAG test data in |
| Broche 137 | TDO — JTAG test data out |
| Broche 138 | VCC5 — 5 V supply |
| Broche 139 | VSS — Ground |
| Broche 140 | NC — Not connected (per datasheet) |
| Broche 141 | NC — Not connected (per datasheet) |
| Broche 142 | NC — Not connected (per datasheet) |
| Broche 143 | NC — Not connected (per datasheet) |
| Broche 144 | NC — Not connected (per datasheet) |
Applications typiques
SAK-C167CR-LM convient pour 6 applications: Automotive Body Control Module, Industrial PLC and CANOpen Slave, Off-Road Vehicle and Agricultural ECU, Motor Control and PWM Drive, HVAC and Building Automation Controller, CAN-Based Sensor Hub / IoT Edge Node.
Automotive Body Control Module
The SAK-C167CR-LM is widely used in body control ECUs, door zone modules and lighting controllers thanks to its dual CAN 2.0B nodes, 16-channel 10-bit A/D and 111 GPIO lines. The ROM-less architecture lets the bootloader pull CAN/UART firmware updates into external boot Flash, supporting in-field ECU re-flashing via UDS. Industrial -40 C to +125 C ambient rating handles under-dash thermal stress without derating. Estimated: at 25 MHz CPU clock and typical CAN traffic load of 60% bus utilisation, the core has ~40% headroom for application code.
Recommandé
Industrial PLC and CANOpen Slave
The SAK-C167CR-LM is well-suited to industrial PLC backplanes, CANOpen slave nodes and PROFIBUS-DP slave controllers. The dual CAN nodes let the device act as a bridge between a CANOpen management bus and a second sensor bus, while the 16-bit external bus can address up to 16 Mbytes of external SRAM/Flash for large protocol stacks. Industrial -40 C to +125 C operating range tolerates factory-floor thermal cycling. Estimated: a full CANOpen stack requires ~32 Kbytes of code, so external Flash is mandatory given the ROM-less 'K' variant.
Recommandé
Off-Road Vehicle and Agricultural ECU
The SAK-C167CR-LM is used in tractors, harvesters and off-road equipment ECUs where dust, vibration and temperature extremes demand robust industrial-grade silicon. The on-chip PLL allows a single 5 MHz external crystal to generate the 25 MHz CPU clock, simplifying EMI-sensitive designs. The 16-channel A/D converter reads sensor inputs (coolant, hydraulic pressure, RPM) directly, while dual CAN nodes connect to ISO 11783 (ISOBUS) and a proprietary cab network. ROM-less architecture enables supplier-specific calibration data stored in external Flash.
Recommandé
Motor Control and PWM Drive
The C167CR derivative integrates the CAPCOM6 unit with three 16-bit capture/compare registers, providing flexible PWM generation for BLDC, stepper and DC-motor drives. With a 25 MHz CPU clock, the PWM timer granularity is 40 ns, enabling precise commutation at high electrical frequencies. The 16-channel A/D samples back-EMF and current-sense signals synchronised to the PWM edges via the capture unit. ROM-less design supports application-specific firmware across motor variants from the same PCB platform.
Recommandé
HVAC and Building Automation Controller
The SAK-C167CR-LM is a common controller in HVAC and building-automation systems, where its dual CAN nodes support BACnet over CAN or proprietary management buses, and the 16-channel A/D reads temperature, pressure and humidity sensors. Industrial -40 C to +125 C operating range tolerates rooftop plant-room conditions. The ROM-less 'K' variant lets a single PCB host multiple firmware variants for different building zones. External bus interface supports a small graphical LCD for local operator display.
Recommandé
CAN-Based Sensor Hub / IoT Edge Node
The SAK-C167CR-LM acts as a CAN-based sensor hub aggregating data from up to 16 analog sensors (via the on-chip A/D) and forwarding it over either of the two CAN 2.0B nodes. Its 16.5 MIPS throughput is sufficient to run a CANOpen stack with local pre-processing and filtering, offloading the upstream gateway. ROM-less architecture enables per-deployment firmware customisation. The industrial temperature grade is suitable for outdoor enclosure applications including smart-metering and environmental monitoring.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour SAK-C167CR-LM — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | SAF-C167CR-LM HA+ | SAF-C167CR-LM | SAK-C167CR-LM HA+ | SAK-C167CS-LM | SAK-C167SR-LM |
|---|---|---|---|---|---|---|
| Package | PQFP-144 (LM) | PQFP-144 (LM) - same | PQFP-144 (LM) - same | PQFP-144 (LM) - same | PQFP-144 (LM) - same | PQFP-144 (LM) - same |
| Brand | Infineon Technologies (formerly Siemens Semiconductor) | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Operating Temperature Range | -40 C to +125 C (SAK industrial) | -40 C to +125 C (SAF automotive, AEC-Q100-style) | -40 C to +125 C (SAF automotive) | -40 C to +125 C (SAK industrial, HA+ burn-in) | -40 C to +125 C (SAK industrial) | -40 C to +125 C (SAK industrial) |
| On-chip Program Memory | None (ROM-less, 'K' suffix) | None (ROM-less) | None (ROM-less) | None (ROM-less) | None (ROM-less) | None (ROM-less) |
| Maximum CPU Clock | 25 MHz | 25 MHz | 25 MHz | 25 MHz | 25 MHz | 25 MHz |
| CAN 2.0B Nodes | 2 | 2 | 2 | 2 | 2 | 1 (-50% vs CR) |
| CAPCOM6 PWM Unit | Yes (three 16-bit capture/compare registers) | Yes | Yes | Yes | No (C167CS variant) | Yes |
| Lifecycle Status | Last-time-buy (Infineon legacy C166 family) | Last-time-buy | Last-time-buy | Last-time-buy | Last-time-buy | Last-time-buy |
Principaux différenciateurs
- Industrial temperature grade with documented cross-reference to automotive SAF variant (vs SAB-C167CR-LM)
- Includes CAPCOM6 advanced PWM unit for motor control (vs SAK-C167CS-LM)
- Dual CAN 2.0B nodes for gateway/zonal architectures (vs SAK-C167SR-LM)
Notes de conception
Estimated: the PQFP-144 package has a 0.65 mm pitch and approximately 31 mm x 31 mm body. Place a 4-layer PCB with a continuous ground plane directly under the device, and stitch the ground plane to the VSS pins with 8 to 12 vias distributed around the package perimeter. Route the external address/data bus as 50 ohm controlled-impedance traces, and keep the /RD and /WR strobes length-matched to within 1 cm to avoid bus contention on external memory accesses. Decoupling: place one 100 nF ceramic cap per VCC5/VSS pair plus one 10 uF bulk cap within 5 mm of the supply pins.
Do not assume SAK-, SAB- and SAF- prefixes are software-compatible at the same temperature. Although the C167CR die is identical across prefixes, only SAF-C167CR-LM HA+ carries AEC-Q100-style automotive qualification documentation. Choose SAF for OEM automotive ECUs and SAK for industrial designs. Also note that the 'K' (ROM-less) suffix means an external boot Flash is mandatory - the device does not start without valid code at the external /CS0 memory region. Verify the /EA pin is strapped correctly (high = internal ROM, low = external bus boot).
Estimated: the dual CAN nodes drive the TXD lines at CMOS levels; always use a dedicated CAN transceiver (TLE7250, TJA1050) between the MCU and the bus. Keep the TXD/RXD traces shorter than 5 cm, place a 120 ohm termination resistor at each end of the CAN bus, and isolate the CAN ground from chassis ground with a 1 nF Y-rated capacitor plus a common-mode choke for ESD immunity. Failure to add bus termination causes intermittent frame errors at high bus utilisation and is the most common cause of field returns for legacy C167CR designs.
Estimated: at 25 MHz CPU clock with full peripheral activity, the SAK-C167CR-LM dissipates approximately 250 to 350 mW. The PQFP-144 has theta_JA of approximately 35 C/W on a 4-layer JEDEC test board, so the junction temperature rise is roughly 10 to 12 C above ambient. Across the full -40 C to +125 C industrial operating range this stays well below the silicon limit, but ensure the external Flash and bus transceivers are also rated to the same temperature band, since they typically dominate the board-level thermal budget.
Informations de conformité
RoHS-compliant PQFP-144 lead-free package per Infineon datasheet family. SAK prefix provides industrial -40 C to +125 C ambient temperature rating but is not AEC-Q100 qualified - choose SAF-C167CR-LM HA+ for AEC-Q100 automotive applications.
